8-port gigabit ethernet poe+ smart managed pro switch with 2 sfp ports (75w), 8-port gigabit high power poe+ smart managed pro switch with 2 sfp ports (190w) (2 pages)
NETGEAR, Inc. Technical Support Thank you for choosing NETGEAR. To register your product, get the latest product updates, get support online, or for more information about the topics covered in this manual, visit the Support website at http://support.netgear.com...
About This Manual The NETGEAR ® ProSafe GS510TP Hardware Installation Guide describes how to install and power on the GS510TP Smart Switch. The information in this manual is intended for readers with intermediate computer and Internet skills. Conventions, Formats, and Scope...
DANGER: This is a safety warning. Failure to take heed of this notice may result in personal injury or death. • Scope. This manual is written for the GS510TP Smart Switch according to these specifications: Product Version GS510TP Smart Switch...
Congratulations on the purchase of your NETGEAR ® ProSafe GS510TP Smart Switch. The GS510TP is a supplement to the Gigabit Advanced Smart Switch family. Available as a desktop or rack-mountable.The GS510TP is a PoE-supportable low-port switch with two fiber uplinks included.
The maximum segment length is 328 feet (100 meters) over Category 5 Unshielded Twisted-Pair (UTP) cable. Features The following list identifies the key features of the GS510TP Smart Switch: • Eight RJ-45 10/100/1000 Mbps autosensing Gigabit Ethernet switching ports.
Rubber footpads for tabletop installation • Rack mount kit • AC power cord • Installation guide • Smart Switch Resource CD with the Netgear Smart Control Center and User’s manual If any item is missing or damaged, contact the place of purchase immediately. Introduction...
Device Hardware Interfaces GS510TP Front-Panel Configuration The GS510TP has eight 10/100/1000 Mbps autosensing and two 1000 Mbps SFP Gigabit Ethernet switching ports. Each RJ-45 port is capable of sensing the line speed and negotiating the duplex mode with the link partner automatically.
Fan LED • PoE Max LED GS510TP Back-Panel Configuration Figure 3 illustrates the GS510TP back panel. Power Connector Figure 3. GS510TP Back Panel The back panel contains the following: • Internal 150W open frame power supply for the GS510TP. Physical Description...
NETGEAR GS510TP Smart Switch LED Designations Port LEDs Table 1 describes the RJ-45 and SFP port LED designations. There are two LEDs for each Each SFP port has its own indication LED. RJ-45 port. Table 1. Port LEDs Designation Speed/Link/Activity SPD/Link/ACT LED: •...
NETGEAR GS510TP Smart Switch System LEDs Table 2 describes the system LED designations. Table 2. System LEDs Designation Power/Status LED • Solid Green = Power is supplied to the switch and the switch is operating normally. • Solid Yellow = The switch is booting.
NETGEAR GS510TP Smart Switch device such as a paper clip into the opening to press the recessed button. The front-panel LEDs should extinguish and light again as the switch performs its Power On Self Test (POST). Factory Defaults Button The Smart Switch has a Factory Defaults button on the front panel so that you can remove the current configuration and return the device to its factory settings.
1000 Mbps hubs and switches. Desktop Switching The GS510TP Smart Switch can be used as a desktop switch to build a small network that enables users to have 1000 Mbps access to a file server. With full-duplex enabled, the switch port connected to the server or PC can provide 2000 Mbps throughput.
Installation This chapter describes the installation procedures for your NETGEAR GS510TP Smart Switch. Switch installation involves the following steps: Step 1: Preparing the Site Step 2: Installing the Switch Step 3: Checking the Installation Step 4: Connecting Devices to the Switch...
Step 2: Installing the Switch The GS510TP Smart Switch can be used on a flat surface or mount in a rack. Installing the Switch on a Flat Surface The switch ships with four self-adhesive rubber footpads. Stick one rubber footpad on each of the four concave spaces on the bottom of the switch.
Step 4: Connecting Devices to the Switch The following procedure describes how to connect PCs to the switch’s RJ-45 ports. The GS510TP Smart Switch contains Auto Uplink technology, which allows the attaching of devices using either straight-through or crossover cables.
Step 6: Managing the Switch using a Web Browser or the PC Utility The GS510TP Smart Switch contains software for viewing, changing, and monitoring the way it works. This management software is not required for the switch to work. The ports can be used without using the management software.
Page 23
NETGEAR GS510TP Smart Switch Note: When the device powers up, there is a default IP address already configured on the device. The default IP address is 192.168.0.239 and subnet mask 255.255.255.0. Installation...
Troubleshooting This chapter provides information about troubleshooting the NETGEAR Smart Switch. Topics include the following: • Troubleshooting Chart • Additional Troubleshooting Suggestions Troubleshooting Chart The following table lists symptoms, causes, and solutions of possible problems. Table 4. Troubleshooting Chart Symptom...
AC power from the switch and then reapply AC power. If the problem continues, contact NETGEAR technical support. In North America, call 1-888-NETGEAR. If you are outside of North America, please refer to the support information card included with your product.
NETGEAR GS510TP Smart Switch Protected Port IP and MAC ACL Green feature (Auto power down and Short cable power saving) DoS protection Interface Eight RJ-45 connectors for 10BASE-T, 100BASE-TX, and 1000BASE-T (Auto Uplink™ on all ports) Two SFP slots for SFP modules...
NETGEAR GS510TP Smart Switch Operating humidity: 10% to 90% maximum relative humidity, noncondensing Storage temperature: –20°C to 70°C (–4 to 158°F) Storage humidity: 5% to 95% maximum relative humidity, noncondensing Electromagnetic Emissions FCC Class A CE Class A: Includes EN55022 (CISPR 22), 55024, and 50082-1...
Connecting Devices to the Switch Low Latency Copper Crossover Media Access Control Default IP Address Default Reset Button Desktop Switching Netgear Smart Control Center Utility Device Hardware Interfaces Duplex Mode Operating Conditions Operating Environment Example of Desktop Switching Operating humidity Overview...
Page 32
NETGEAR GS510TP Smart Switch Preparing the Site Rack-mount Kit Reset Button RJ-45 RJ-45 Ports Rubber footpads Site Requirements Smart Switch Resource CD Straight-through System LEDs technical support Temperature trademarks Traffic Control Troubleshooting Chart User Intervention User’s Manual Ventilation VLAN Web-based Graphical User Interface...