Advertisement
SETTING THE WEEKDAY (W) AND SINGLE DAY (S)
ALARMS
• Press ALARM ON/OFF button once to enter into the
alarms setting mode. The default alarm is a Weekday alarm
(W). The abbreviation "OFF" with a letter "W" next to it
will be displayed, if the alarm has not been set previously.
• Press and hold ALARM ON/OFF button for two
seconds. The hour digit will flash.
• Adjust the hour using UP ( ) or DOWN ( ) buttons
• Press ALARM ON/OFF button again. The minute digits
will flash
• Adjust the minutes using UP ( ) or DOWN ( ) buttons
• Press ALARM ON/OFF button again to confirm and the
weekday alarm time will be set
• Set Single day alarm if desired in the same manner
SETTING THE ICE WARNING ALARM (PRE-AL)
If Weekday or Single day alarm is set, the Ice Warning
Alarm can be programmed.
• Press ALARM ON/OFF button once to enter into the
Ice Warning Alarm setting mode. The abbreviation OFF
with a PRE-AL next to it will be displayed.
• Press and hold ALARM ON/OFF button for two seconds.
The number "30" will flash, meaning that if selected, the
alarm will sound 30 minutes earlier than the Weekday or
Single alarm.
• Select the desired Ice Warning Alarm interval in 15 minutes
increments between 15 and 90 minutes, using UP ( ) or
DOWN ( )buttons
• Press ALARM ON/OFF button to confirm and exit from
the alarm setting mode.
ACTIVATING THE ALARM
• Press ALARM ON/OFF button to enter into the desired
alarm mode.
• Press UP ( ) to activate or DOWN ( ) to deactivate desired
• If alarm are activated, the corresponding icons W, S or
PRE-AL will be displayed.
17
CONTINUES TIME AND TEMPERATURE PROJECTION
• Connect AC/DC adapter provided with the product to
project the time and temperature image continuously.
• Slide the CONTINUE PROJECTION switch to the
arrow direction shown on the main unit's side: the
current time and temperature will be projected on the
wall or the ceiling.
LIGHT SENSOR
The Weather Forecaster is equipped with the light sensor
which detects the environmental light conditions. At the
light conditions lower than 100 LUX, the LCD will light
up automatically if AC adapter is connected. The backlight
can be set using the LIGHT SENSOR switch to the
following modes:
AUTO - automatic LCD backlight
ON - continuous LCD backlight
OFF - turned off LCD backlight
19
SNOOZE
When any alarm sounds, press the SNOOZE/LIGHT
button to temporarily stop the alarm. After the SNOOZE /
LIGHT button are depressed, the alarm sound will resume
in five minutes.
If the alarm is not disabled after that, it will sound for four
more minutes and then will stop by itself.
PROJECTION
The Weather Forecaster is capable of projecting images for
a short period, as well as continuously.
TIME AND REMOTE TEMPERATURE PROJECTION
• Press SNOOZE/LIGHT button once to project the
current time and the remote temperature image for five
seconds.
PM
NOTE: The Weather Forecaster projects only Channel
1 (one) remote temperature
• Press FLIP button to rotate projected image 180° clockwise
• Press and hold FLIP button for 2 seconds to change
temperature information from remote to indoor
PM
• Press and hold FLIP button for 2 seconds again and the
projected image will rotate between the remote and
indoor temperature every 5 seconds.
NOTE: During initial product setup (remote sensor and
atomic time signal search) there will be no remote
temperature projected.
18
PRECAUTIONS
This product is engineered to give you years of satisfactory
service if handled carefully. Here are a few precautions:
• Do not immerse the units in water.
• Do not clean the units with abrasive or corrosive materials.
They may scratch the plastic parts and corrode the electronic
circuits.
• Do not subject the product to excessive force, shock, dust,
temperature, or humidity, which may result in malfunctions,
shorter lifespan, damaged batteries, and damaged parts.
• Do not tamper with the units internal components. Doing
so will invalidate the warranty and may cause damage.
These units contain no user-serviceable parts.
• Use only fresh batteries. Do not mix new and old batteries.
• Read the user's manual thoroughly before operating the
units.
TROUBLESHOOTING
Check here before contacting customer service.
Issue
Symptom
Main unit
US Atomic Time
signal is not received
Remote sensor
Cannot locate remote
sensor
Cannot change the
channel
Cannot change the ºC
to ºF and back
Data does not match
data on the main unit
20
Solution
Place unit by the
window and keep it
there overnight
Check batteries
Check location
Press and hold DOWN
( ) button on the main
unit to search for the
signal form the remote
sensor
Press "RESET" after
setting the channel
Press "RESET" after
setting ºC/ºF
Initiate manual sensor
search (Press and hold
DOWN ( ) button on
the main unit)
Advertisement
