Cisco 3640 Quick Start Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. 3640 Series
  6. Quick start manual
Cisco 3640 Quick Start Manual

Cisco 3640 Quick Start Manual

Modular access routers
Hide thumbs Also See for 3640:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual , Configuration Manual
Cisco 3620 and Cisco 3640 Modular Access Routers
INCLUDING LICENSE AND WARRANTY
Installation, License and Warranty
1
Cisco 90-Day Limited Hardware Warranty Terms
Documents, Equipment, and Tools
2
Install Chassis
3
4
Connect Cables
5
Power Up the Router
Perform Initial Configuration
6
Interface Numbering
7
8
Where to Go Next
9
Obtaining Documentation
Documentation Feedback
10
Obtaining Technical Assistance
11
12
Obtaining Additional Publications and Information
Quick Start Guide

Advertisement

Table of Contents
loading

Related Manuals for Cisco 3640

Summary of Contents for Cisco 3640

  • Page 1 Quick Start Guide Cisco 3620 and Cisco 3640 Modular Access Routers INCLUDING LICENSE AND WARRANTY Installation, License and Warranty Cisco 90-Day Limited Hardware Warranty Terms Documents, Equipment, and Tools Install Chassis Connect Cables Power Up the Router Perform Initial Configuration...

  • Page 2: Cisco 90-Day Limited Hardware Warranty Terms

    Replacement, Repair, or Refund Policy for Hardware Cisco or its service center will use commercially reasonable efforts to ship a replacement part within ten (10) working days after receipt of a Return Materials Authorization (RMA) request. Actual delivery times can vary, depending on the customer location.

  • Page 3: Documents, Equipment, And Tools

    Install Chassis Safety Information For safety information you need to know before working on your Cisco router, refer to the Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Regulatory Compliance and Safety Information document that accompanied this device.

  • Page 4: Warning Definition

    Warning Definition IMPORTANT SAFETY INSTRUCTIONS Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.
  • Page 5 Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Per le traduzioni delle avvertenze riportate in questo documento, vedere le avvertenze di sicurezza che accompagnano questo dispositivo.
  • Page 6 Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
  • Page 7 Advarsel VIGTIGE SIKKERHEDSANVISNINGER Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.
  • Page 8 Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017 Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches).

  • Page 9: Installing The Chassis

    Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Installing the Chassis You can set the chassis on a desktop or install it in a rack. A Cisco 3620 chassis can also be mounted on a wall or other flat surface. See the applicable instructions following.
  • Page 10 Attach the mounting brackets to the chassis as shown in the applicable figure, Figure 1 through Figure 8, using the Phillips-head screws provided. Attach the second bracket to the opposite side of the chassis. Note When installed in a 19-inch rack with a 17.5-inch opening, Cisco 3620 and Cisco 3640 routers protrude beyond the front of the rack. Figure 1 Cisco 3620 or Cisco 3640 Bracket Attachment—Front Panel Forward (19-Inch Rack with a 17.5-Inch Opening)
  • Page 11 Note: The second bracket attaches to the other side of the chassis. Figure 4 Cisco 3620 or Cisco 3640 Bracket Attachment—Rear Panel Forward (19-Inch Rack with a 17.5-Inch Opening) Note: The second bracket attaches to the other side of the chassis.
  • Page 12 Figure 5 Cisco 3620 or Cisco 3640 Bracket Attachment—Rear Panel Forward (19-Inch Rack with a 17.75-Inch Opening) Note: The second bracket attaches to the other side of the chassis. Figure 6 Cisco 3620 or Cisco 3640 Bracket Attachment—Rear Panel Forward (23- or 24-Inch Rack) Note: The second bracket attaches to the other side of the chassis.
  • Page 13 Attaching Rubber Feet If you are mounting a Cisco 3620 on a wall, you must install the rubber feet that are supplied in the accessory kit. They provide a space for air circulation. Peel the rubber feet from the adhesive strip, and attach one foot at each corner to the bottom of the chassis.

  • Page 14: Installing On A Desktop

    Installing on a Desktop If you are mounting a Cisco 3620 on a desktop, you must install the rubber feet that are supplied in the accessory kit. They provide a space for air circulation. Peel the rubber feet from the adhesive strip, and attach one foot at each corner to the bottom of the chassis.
  • Page 15 Diagonal attachment of the ground lug to the bracket provides clearance for the RPS power cable. Step 5 Connect the other end of the ground wire to a suitable grounding point at your site. Figure 12 NEBS-Compliant Ground Lug Attachment on a Cisco 3620 Router with Internal AC or DC Power Supply Power supply Bracket...
  • Page 16 NEBS-Compliant Ground Lug Attachment on a Cisco 3640 Router Ground lug Power supply Figure 15 Ground Lug Attachment Using Ring Terminal on a Cisco 3620 Router with Internal AC or DC Power Supply Ring terminal attached Power to a bracket...
  • Page 17 Figure 16 Ground Lug Attachment Using Ring Terminal on a Cisco 3620 Router with Redundant Power Supply (Cisco RPS) DC INPU T FOR USE WITH CISC O RPS +5V– – –14A , +12V – – –5A, -12V– – –3A Power...

  • Page 18: Connect Cables

    Connect Cables Warning Do not work on the system, or connect or disconnect cables during periods of lightning activity. Statement 1001 System Management Connections The connections described in Table 1 provide system management access. Table 1 System Management and Power Connections Port Color Connected to:...
  • Page 19 For Cisco 3620 routers, strip the wires to the appropriate length for the terminal block on the power supply. For Cisco 3640 routers, crimp appropriate ring terminals or spade terminals to the DC power input wires. Strip the wires to the appropriate length for the terminals used. The following warning applies to Cisco 3640 routers:...

  • Page 20: Connecting Routers To The Cisco Redundant Power System

    Connecting Routers to the Cisco Redundant Power System If your router uses the Cisco Redundant Power System (RPS), refer to the Cisco RPS Hardware Installation Guide for instructions about the power connections.To locate these documents, see the “Where to Go Next” section on page 32.

  • Page 21: Wan, Lan, And Voice Connections

    DB-15 to twinax, or DB-15 to RJ-45 Token Ring UTP, purple Token Ring device RJ-45 Token Ring cable STP, purple 56/64-kbps DSU/CSU 8-pin modular, blue RJ-48S interface RJ-48 straight-through 1. See the Cisco Modular Access Router Cable Specifications document for information about selecting these cables.

  • Page 22: Power Up The Router

    • Activity (green)—Blinks during system activity, such as interrupts and packet transfers Power-Up Procedure Perform this procedure to power up your Cisco router and verify that it goes through its initialization and self-test. When the procedure is finished, the Cisco router is ready to configure.

  • Page 23: Perform Initial Configuration

    You can configure your router by using one of the following methods: • Cisco Router and Security Device Manager (SDM)—If your router was purchased with a VPN bundle, SDM is installed on the router. For instructions on configuring your router by using SDM, refer to the Cisco Router and Security Device Manager (SDM) Quick Start Guide that shipped with your router.

  • Page 24: Initial Configuration Using Cisco Router And Security Device Manager

    If Your Router Has No Ethernet Adapter in Slot 0 Cisco 3620 and Cisco 3640 routers have no built-in Ethernet ports. However, many of these routers ship with a Fast Ethernet network module in chassis slot 0. The SDM default configuration file assumes this to be the case. If your router has no Ethernet module in chassis slot 0, you need to do one of the following: •...
  • Page 25 Enter the username sdm and the password sdm in the dialog box. Step 4 A window appears informing you that Verisign certifies that this is a Cisco application. Click Yes, or click Grant to accept the certificate and proceed. Additional certificate windows appear if you are using Netscape; click Grant to accept the certificates.
  • Page 26 Figure 21 SDM Launch Page If the SDM Launch page does not appear when you enter the URL https://10.10.10.1/flash/sdm.shtml, test the connection between the PC and the router by doing the following: a. Check that the POWER LED on the router is on, and that the ACTIVITY LED is on, indicating an active Ethernet connection between the router and the PC.

  • Page 27: Initial Configuration Using The Setup Command Facility

    Step 11 When the SDM System Overview window appears, you can use the wizard buttons on the left side of the window to configure other features. Buttons are provided for LAN, WAN, firewall, and VPN configurations. For more information about SDM, refer to the Cisco Router and Security Device Manager Troubleshooting Guide at the following URL: http://www.cisco.com/go/sdm...
  • Page 28 Step 8 A summary of the available interfaces is displayed. Note The interface numbering that appears is dependent on the type of Cisco modular router platform and on the installed interface modules and cards. Current interface summary Any interface listed with OK? value "NO" does not have a valid configuration...
  • Page 29 Step 12 The user prompt appears. 3600> When you have completed the initial configuration tasks, your Cisco router is ready to configure for specific functions. See the “Where to Go Next” section on page 32 for information about locating documentation for advanced configuration procedures.

  • Page 30: Initial Configuration Using The Cli (Manual Configuration)

    For configuration using the CLI, refer to the applicable configuration procedures in the Software Configuration Guide: Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers. See the “Where to Go Next” section on page 32 for information about accessing this document.

  • Page 31: Slot Numbering

    Slot Numbering The Cisco 3620 or Cisco 3640 router chassis contains two or four slots in which you can install modules. You can install any module into any available slot in the chassis. For Cisco 3620 and Cisco 3640 routers, the slots are numbered as follows: •...

  • Page 32: Where To Go Next

    To access Cisco 3600 series platform documentation on Cisco Connection Online (CCO): On the Cisco.com home page at http://www.cisco.com, locate the Technical Documentation tab, and click on “Locate Technical Documentation on Cisco Connection Online.” Under the Product Documentation heading, navigate to Modular Access Routers and to the documentation for your router.

  • Page 33: Documentation Feedback

    For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.

  • Page 34: Definitions Of Service Request Severity

    To ensure that all service requests are reported in a standard format, Cisco has established severity definitions. Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.
  • Page 36 Internet Quotient, TransPath, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.

This manual is also suitable for:

3620

Table of Contents