Advertisement
Quick Links
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new product.
© 2023 JVCKENWOOD Corporation
CA-LID98
REPLACEMENT 6" X 9" SADDLEBAG LIDS DESIGNED AND
ENGINEERED FOR 1998-2013 HARLEY-DAVIDSON® MOTORCYCLES
WITH FACTORY-STYLE HARD SADDLEBAGS
INSTRUCTION MANUAL
JVCKENWOOD Corporation
Advertisement
Related Manuals for Kenwood CA-LID98
Summary of Contents for Kenwood CA-LID98
- Page 1 CA-LID98 REPLACEMENT 6” X 9” SADDLEBAG LIDS DESIGNED AND ENGINEERED FOR 1998-2013 HARLEY-DAVIDSON® MOTORCYCLES WITH FACTORY-STYLE HARD SADDLEBAGS INSTRUCTION MANUAL JVCKENWOOD Corporation Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new product.
-
Page 2: Table Of Contents
KENWOOD assumes ZERO RESPONSIBILITY for fitment issues, or water leaks when any speaker brand other than KENWOOD is used. Be sure of all clearances and inspect the parts carefully BEFORE painting. Do Not Use “Thread Lock” or “Screw Glue” of any kind, as it destroys plastic and will cause part failure. -
Page 3: Section 1: Bag And Lid Prep
Section 1 - Bag and Lid Prep Installation procedure 1. Start by removing the 2 screws on the underside of the lid that secures the grille in place. Lift up slightly on the grille and slide out. Remove the saddlebag from the bike and put it on a stable working surface (placing blankets, towels, etc. -
Page 4: Section 3: Preparing The New Lid
Section 2 - Disassembling The Factory Lid - Cont. 2. With the tether off, fold the factory lid all the way over, exposing the 5 screws highlighted by white arrows in Fig 1.4. When these are removed, the factory lid will be free from the saddlebag. -
Page 5: Section 4: Mounting The Speakers
Fig 1.5 by the white rectangle. The 4 white circles in Fig 1.5 shows “locators” built into the lid to fit the KENWOOD XM69R speakers when used. Use the supplied 6 x 9 gasket (which is approximately 3/8” (9mm) thick) as a “shim” between the speakers and the lid. Locate the bag that came with your kit that has 8 Phillips head screws and use those (4 per lid) to secure your speaker to the lid. -
Page 6: Section 5: Routing The Wires In The Saddlebag
Section 5 - Routing The Wires In The Saddlebag NOTE: Included in the kit are adhesive “pads” that when attached, have a provision to secure the wires in place using the supplied zip-ties. Half of the supplied zip-ties and half the supplied pads are for one saddlebag, while the other half are for the other saddlebag. -
Page 7: Section 7: Wiring The Lids To The Amplifier
Section 7 - Wiring The Lids To The Amplifier NOTE: The 4-pin connector will plug into the KENWOOD XM160-2-98 amplifier. If you’re using another brand of amplifier, you will see that the wires near the 4-pin plug are labeled. - Page 8 Important Notes ©2023 JVCKENWOOD Corporation. All Rights Reserved. KENWOOD® and eXcelon® are registered trademarks of JVCKENWOOD Corporation. Harley-Davidson®, Electra Glide®, Road Glide®, Street Glide®, Ultra Classic®, Tri Glide®, CVO™, Screamin Eagle® and Tour-Pak® are trademarks or registered trademarks of Harley-Davidson, Inc. and/ or its affiliates and if used or implied are for reference only.