Panasonic ES-LT5N, ES-LT3N - Rechargeable Shaver Manual

Before operating this unit, please read these instructions completely and save them for future use.

Intended use

• This WET/DRY shaver can be used for wet shaving using shaving lather or for dry shaving. You can use this watertight shaver in the shower and clean with water. The following symbol means suitable for use in a bath or shower.
  

► Notes

• Treat yourself to wet lather shaves for at least three weeks and notice the difference. Your Panasonic WET/DRY shaver requires a little time to get used to because your skin and beard need about a month to adjust to any new shaving method.
• Do not bring the system outer foil into contact with hard object.
  Doing so may damage the blades as they are very thin and deform easily.
• Do not dry the main unit with a dryer or a fan heater.
  Doing so may cause malfunction or deformation of the parts.
• Do not leave the shaver exposed to direct sunlight with the foil frame detached.
  Doing so may deteriorate the waterproof rubber and degrade waterproof function, which may cause to malfunction.
• Store the shaver in a place with low humidity after use.
  Failure to do so may cause malfunction due to condensation or rust.
• Keep both the inner blades inserted. If only one of the inner blades is inserted, the shaver may be damaged.
• If you clean the shaver with water, do not use salt water or hot water. Do not soak the shaver in water for a long period of time.

Parts identification

1. Main body
   1. Protective cap
   2. System outer foil
   3. Foil frame
   4. Foil frame release buttons
   5. Thumb rest
   6. Power switch
      To turn the shaver on and off and also lock and unlock the power switch.
   7. Lamp display
      1. Battery capacity lamp
      2. Shaving sensor lamp ()
      3. Switch lock lamp ()
      4. Charge status lamp ( )
   8. Appliance socket
   9. Outer foil section
   10. System outer foil release buttons
   11. Inner blades
   12. Trimmer
   13. Trimmer handle
   14. Main body rear terminals
2. AC adaptor (RE7-87)
   15. Adaptor
   16. Power plug
   17. Cord
   18. Appliance plug

Accessories

3. Travel pouch
4. Charging stand ES-LT5N
   19. Charging plug

Operation and display of the switch lock

Locking the power switch

1. Press the power switch once and then release.
   
   • The shaver starts operating.
     
     The switch lock lamp is off.
2. Press the power switch for more than 2 seconds when the shaver is operating.
   
   • The shaver will stop operating.
     
     The switch lock lamp will light up.
3. Release the power switch.
   
   The switch lock lamp will turn off after 5 seconds.

Unlocking the power switch

1. Press the power switch for more than 2 seconds.
   
   
   The switch lock lamp will blink.
2. Once the shaver starts operating, release the power switch.
   
   
   The switch lock lamp will turn off.

• The power switch cannot be unlocked while charging.

Checking the power switch is locked

Press the power switch while it is locked.

The switch lock lamp will blink and then turn off after 5 seconds.

• You can also check this by unplugging the AC adaptor while charging.

Charging the shaver

1. Insert the appliance plug into the shaver.
   
   • Turn the shaver off before inserting.
2. Plug in the adaptor into a household outlet.
   • Wipe off any water droplets on the appliance socket.
   • Check that the charge status lamp ( ) glows.
   • Charging is completed after approx. 1 hour.
     The charging time may differ with the charging capacity.
   • Charging the appliance after each use will not affect the battery life.
3. Disconnect the adaptor after charging is completed.
   • Charging the battery for more than 1 hour will not affect battery performance.
   • If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the proper configuration.

While charging

The charge status lamp ( ) glows.
The number of the battery capacity lamp will increase as charging progresses.

After charging is completed

The battery capacity lamp and the charge status lamp () will light up and then turn off after 5 seconds.

Abnormal charging

The charge status lamp () will blink twice every second.

• Recommended ambient temperature for charging is 10 – 35°C (50 – 95°F). It may take longer to charge or the battery may fail to charge properly in extremely high or low temperatures.
  Charge the shaver within the recommended ambient temperature range.
• When charging the shaver for the first time or when it has not been in use for more than 6 months, the charging time may change or the charge status lamp () may not glow for a few minutes. It will eventually glow if kept connected.
• If there is noise from radio or other source while using the shaver, move to a different location to use the shaver.

Charging with the charging stand ES-LT5N

1. Insert the appliance plug into the charging stand.
2. Place the shaver on the charging stand.
3. Plug in the adaptor into a household outlet.

Using the shaver

1. Press the power switch.
   • The power cannot be turned on when the switch lock lamp ( ) blinks, as the power switch is locked.
     Press the power switch for more than 2 seconds to unlock.
2. Hold the shaver as illustrated.
   
3. Shave by slowly gliding the shaver over your face against the grain of the beard.
   • Start shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin becomes accustomed to this shaver. Applying excessive pressure does not provide a closer shave.

► Notes

• If you press the power switch for more than 2 seconds, the sonic vibration cleaning mode is activated.
  You cannot shave in this mode.
• Do not place your fingers on the power switch while using the shaver. This may cause the shaver to lock the power switch or turn off. Place your fingers on the thumb rest while using the shaver.
• The appliance may not operate in an ambient temperature approximately 5°C (41°F) or lower.
• Depending on the beard thickness or the amount of beard trimmings in the shaver head, the shaving sensor may not react and the driving sound may not change. This is not abnormal.
• The shaving sensor may not respond depending on the type of the shaving gel and shaving foam, but this is normal.
• The shaving sensor may not respond when the remaining battery capacity is low. If this happens, recharge the shaver.
• Avoid the following situations to prevent damaging the system outer foil. Applying pressure to any part of the system outer foil or bringing the system outer foil into contact with hard object may cause damage on the system outer foil.
  • Shaving with only a part of the system outer foil.
  • Finger or nail coming into contact with the system outer foil.

Switching the shaver head

You can change the pivot action.

FREE
You can move the shaver head.

LOCK
You can lock the shaver head.

Using the trimmer

Slide the trimmer handle up to the "" position so that the trimmer stands upright.

Press and hold the lock release button (a) and slide the trimmer handle down to lower the trimmer.

Trimming sideburns

Slide the trimmer handle up. Turn the shaver on and place at a right angle to your skin and move downwards to trim your sideburns.

Pre-shave

The trimmer can be used for a pre‑shave of long beards. Shave your beard with the shaver head after the pre‑shave.

Reading lamps when using

While using

• The shaving sensor lamp () glows.

When the battery capacity is low

• You can shave 2 to 3 times after "10%" appears. (This will differ depending on usage.)
• The shaver can be used for approximately 2 weeks with a full charge.
  (Based on one 3‑minute dry‑shave use per day until the battery is exhausted)
• The number of usable days varies depending on the following conditions.
  • Beard thickness
  • Pressure applied to the skin
  • Ambient temperature
  • Usage frequency of the sonic vibration cleaning mode

Cleaning the shaver

Do not use kitchen, bathroom, or toilet detergents. Also, do not wipe with thinners, benzine, alcohol etc.

Doing so may result in malfunction.

1. Turn the power switch OFF, and disconnect the AC adaptor.
   • Unlock the switch lock.
2. Apply some hand soap and some water to the system outer foil.
3. Press the power switch for more than 2 seconds to activate the sonic vibration cleaning mode.
   
   • The battery capacity lamps blink in order.
   • After about 20 seconds, it will be automatically turned off.
4. Remove the outer foil section and press the power switch for more than 2 seconds to activate the sonic vibration cleaning mode.
   
5. Clean the shaver, the outer foil section, and the trimmer with running water.
   
   • After rinsing with water, shake the shaver up and down for a few times to remove excess moisture.
     Hitting the vanity, etc., while shaking the shaver may cause malfunction.
   • Splashing is reduced by rinsing the shaver in sonic vibration cleaning mode.
6. Wipe off any drops of water with a dry cloth.
7. Dry the outer foil section, the shaver, and the trimmer completely.
   
8. Attach the outer foil section to the shaver.

Replacing the system outer foil and the inner blades

Removing the outer foil section

Press the foil frame release buttons and lift the outer foil section upwards.

Attaching the outer foil section

After turning the foil frame mark () to the front, securely attach the outer foil section to the shaver until it clicks.

Replacing the system outer foil

1. Press the system outer foil release buttons and pull down the system outer foil.
   
2. Align the foil frame mark () and the system outer foil mark () and securely attach together until it clicks.
   • The system outer foil cannot be reversely attached.
   • Always insert the system outer foil to the foil frame when attaching to the shaver.
   • Do not press the system outer foil release buttons with excessive force.
     Doing so may bend the system outer foil, preventing complete attachment to the foil frame.

Replacing the inner blades

1. Remove the inner blades one at a time.
   
2. Insert the inner blades one at a time.

Replacement parts

Replacement parts are available at your dealer or Service Center.

Troubleshooting

FAQ

Battery life

The life of the battery is 3 years. The battery in this shaver is not intended to be replaced by consumers.

Removing the built-in rechargeable battery

Remove the built-in rechargeable battery before disposing of the shaver.

This figure must only be used when disposing of the shaver, and must not be used to repair it. If you dismantle the shaver yourself, it will no longer be waterproof, which may cause it to malfunction.

• Remove the shaver from the AC adaptor.
• Press the power switch to turn on the power and then keep the power on until the battery is completely discharged.
• Perform steps 1 to 4 and lift the battery, and then remove it.
  
• Take care not to short circuit the positive and negative terminals of the removed battery, and insulate the terminals by applying tape to them.

Specifications

Power source	See the name plate on the AC adaptor. (Automatic voltage conversion)
Motor voltage	3.6 V
Charging time	Approx. 1 hour

This product is intended for household use only.

Safety precautions

To reduce the risk of injury, loss of life, electric shock, fire, and damage to property, always observe the following safety precautions.

Explanation of symbols

The following symbols are used to classify and describe the level of hazard, injury, and property damage caused when the denotation is disregarded and improper use is performed.

	Denotes a potential hazard that will result in serious injury or death.
	Denotes a potential hazard that could result in serious injury or death.
	Denotes a hazard that could result in minor injury.

The following symbols are used to classify and describe the type of instructions to be observed.

This symbol is used to alert users to a specific operating procedure that must not be performed.

This symbol is used to alert users to a specific operating procedure that must be followed in order to operate the unit safely.

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following:

Read all instructions before using this appliance.

To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water. Unplug immediately.
2. Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
3. Except when charging, always unplug this appliance from the electrical outlet immediately after using.
4. Unplug this appliance before cleaning.

To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Close supervision is necessary when this appliance is used by, on, or near children or invalids.
2. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
3. Never operate this appliance when it has a damaged cord or plug, when it is not working properly, after it has been dropped or damaged, or after it has been dropped into water. Return the appliance to a service center for examination and repair.
4. Keep the cord away from heated surfaces.
5. Never drop or insert any object into any opening.
6. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
7. Do not use this appliance with damaged shaving blades and/or foil, as it has the potential to result in facial injury.
8. Always attach plug to appliance first, then to outlet. To disconnect, turn all controls to "off" then remove plug from outlet.

SAVE THESE INSTRUCTIONS

Power supply

Do not connect or disconnect the adaptor to a household outlet with a wet hand.

• Doing so may cause electric shock or injury.

Do not immerse the AC adaptor and the charging stand in water or wash with water.
Do not place the AC adaptor and the charging stand over or near water filled sink or bathtub.
Never use the appliance if the AC adaptor is damaged or if the power plug fits loosely in a household outlet.
Do not damage, modify, or forcibly bend, pull, or twist the cord.
Also, do not place anything heavy on or pinch the cord.

• Doing so may cause electric shock or fire due to a short circuit.

Do not use in a way exceeding the rating of the household outlet or the wiring.

• Exceeding the rating by connecting too many plugs to one household outlet may cause fire due to overheating.

Do not use anything other than the supplied AC adaptor and the charging stand. Also, do not charge any other product with the supplied AC adaptor and the charging stand.

• Doing so may cause burn or fire due to a short circuit.

Always ensure the appliance is operated on an electric power source matched to the rated voltage indicated on the AC adaptor.
Fully insert the adaptor.

• Failure to do so may cause fire or electric shock.

In case of an abnormality or malfunction

Immediately stop using and remove the adaptor if there is an abnormality or malfunction.

• Failure to do so may cause fire, electric shock, or injury.
  <Abnormality or malfunction cases>
  • The main unit, charging stand, adaptor or cord is deformed or abnormally hot.
  • The main unit, charging stand, adaptor or cord smells of burning.
  • There is abnormal sound during use or charging of the main unit, charging stand, adaptor or cord.
• Immediately request inspection or repair at an authorized service center.

This product

This shaver has a built-in rechargeable battery. Do not throw into fire, apply heat, or charge, use, or leave in a high temperature environment.

• Doing so may cause overheating, ignition, or explosion.

Do not modify or repair.

• Doing so may cause fire, electric shock, or injury. Contact an authorized service center for repair (battery change etc).

Never disassemble except when disposing of the product.

• Doing so may cause fire, electric shock, or injury.

Cleaning

Always unplug the adaptor from a household outlet when cleaning.

• Failure to do so may cause electric shock or injury.

Regularly clean the power plug, the appliance plug and the charging plug to prevent dust from accumulating.

• Failure to do so may cause fire due to insulation failure caused by humidity.
  Disconnect the adaptor and wipe with a dry cloth.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

• Failure to do so may cause an accident or injury.

The supply cord cannot be replaced. If the cord is damaged, the AC adaptor should be scrapped.

• Failure to do so may cause an accident or injury.

Preventing accidents

Do not store within reach of children or infants. Do not let them use it.

• Putting the inner blades in the mouth may cause accidents and injury.

Protecting the skin

Do not use excessive pressure to apply the system outer foil to your lip or other part of your face. Do not apply the system outer foil directly to blemishes or injured skin.

• Doing so may cause injury to the skin.

Do not forcefully press the system outer foil. Also, do not touch the system outer foil with fingers or nails when in use.
Do not use this product for hair on head or any other part of the body.

• Doing so may cause injury to skin or reduce the life of the system outer foil.

Do not touch the blade section (metallic section) of the inner blade.

• Doing so may cause injury to your hands.

Check the system outer foil for cracks or deformations before use.

• Failure to do so may cause injury to the skin.

Be sure to place the protective cap on the shaver when carrying around or storing.

• Failure to do so may cause injury to skin or reduce the life of the system outer foil.

Note the following precautions

Do not allow pins or trash to adhere to the power plug, the appliance plug or the charging plug.

• Doing so may cause electric shock or fire due to a short circuit.

Do not share your shaver with your family or other people.

• Doing so may result in infection or inflammation.

Do not drop or hit against other objects.

• Doing so may cause injury.

Do not wrap the cord around the adaptor when storing.

• Doing so may cause the wire in the cord to break with the load, and may cause fire due to a short circuit.

Disconnect the adaptor from the household outlet when not charging.

• Failure to do so may cause electric shock or fire due to electrical leakage resulting from insulation deterioration.

Disconnect the adaptor or the appliance plug by holding onto the adaptor or the appliance plug instead of the cord.

• Failure to do so may cause electric shock or injury.

FOR YOUR CONVENIENCE, WE HAVE ESTABLISHED A TOLL-FREE (IN USA ONLY) NATIONAL ACCESSORY PURCHASE HOT LINE AT 1-800-332-5368.