Panasonic ER-GP80 - AC/Rechargeable Professional Hair Clipper Manual

Intended use

• This clipper is designed for professional use to trim hair. It can be operated on either an AC adaptor or rechargeable battery.
• Before and after each use, apply oil at the places marked with arrows.
• The clipper may become warm during operation and/or charging. This is normal.
• You should not allow permanent wave lotion, hair restorer or hair spray to come into contact with the main body or the blades. Doing so may result in cracking, discoloring or corrosion.
• Clean the housing only with a soft cloth slightly dampened with tap water or soapy tap water. Do not use thinner, benzine, alcohol or other chemicals.
• Before using an attachment, check that it has been installed correctly. Failure to do so may cause hair to be cut too short.

Parts identification

1. Main body
   1. Trimming height indicator
   2. Power switch
   3. Dial (Height adjustment control)
   4. Recharge lamp
   5. Charge status lamp
   6. Appliance socket
2. Blade
   7. Mounting hook
   8. Cleaning lever
   9. Moving blade
   10. Stationary blade
3. 3 mm/4 mm comb attachment
   (3 mm (1/8˝)/4 mm (3/16˝))
4. 6 mm/9 mm comb attachment
   (6 mm (1/4˝)/9 mm (3/8˝))
5. 12 mm/15 mm comb attachment
   (12 mm (1/2˝)/15 mm (5/8˝))
6. Comb attachment shelves
7. Charging stand
   11. Charging plug
   12. Stand socket
8. AC adaptor (RE9-82)
   13. Adaptor
   14. Power plug
   15. Cord
   16. Appliance plug

Accessories

9. Cleaning brush
10. Oil

Charging the unit

• Press the power switch to turn off the power.

1. Connect the appliance plug to the stand socket.
2. Place the clipper on the charging stand.
3. Insert the adaptor into a household outlet.

• Charging is required when the recharge lamp blinks.
  
• The clipper can be used for approximately 5 minutes after the recharge lamp blinks.

When charging starts
Charge status lamp glows.

When charging is completed
The charge status lamp blinks once every second.

10 minutes after charging is completed
The charge status lamp blinks once every 2 seconds.

• 1 full charge will provide approximately 50 minutes of continuous operation.
  The operating time may differ depending on the frequency of use, the operating method and the ambient temperature.
• Charging is completed after approx. 1 hour.
• The charging time may differ when using the clipper for the first time, or if it has not been used for more than 6 months. The lamp on the main body may not glow for several minutes when first starting charging, but will glow when continuing to charge.
• To keep charging the battery will not affect battery performance.
• Recommended ambient temperature for charging is 10°C – 35°C (50°F – 95°F). The battery may not charge properly or not at all under extreme low or high temperatures.
• When the charge status lamp is blinking rapidly (twice every second), there is a charging malfunction. Please charge the battery in the recommended ambient temperature range.
• If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the proper configuration.

Charging without the charging stand

1. Press the power switch to turn off the power, and insert the appliance plug into the clipper.
2. Plug in the adaptor into a household outlet.

AC operation

If you connect the AC adaptor to the clipper in the same way as for charging, and turn on the power, you can use it.

• If the remaining battery is too low, the blades may move slowly or stop, even with the AC operation. In this case, charge the battery for 1 minute or more.
• The battery will be discharged, even with the AC operation.

Using the device

• Press the power switch to turn off the power.
• The appliance may not operate in an ambient temperature approximately 5°C (41°F) or lower.

1. Set the trimming height.
2. Press the power switch to turn on the power.

Setting the trimming height

For a trimming height of 0.8 mm to 2.0 mm, turn the dial to the desired height.

Use an attachment for a trimming height higher than 3 mm or more.

Using the comb attachments

1. Select the trimming heights indicated on the insides and sides of the attachments.
2. Set the dial to "0.8" and then mount the attachment to the clipper as illustrated.
   

Removing the attachment from the clipper
Slide one side of the attachment off the mounting in direction indicated with the arrow.

Care

Removing and mounting the blade

• Be sure to turn off the power before you remove the blade.

Removing the blade
Hold the clipper with the switch facing upward and push the blade with your thumb while catching the blade in your other hand.

Mounting the blade

1. Set the dial to "2.0".
   
2. Fit the mounting hook into the blade mounting on the clipper and push in until it clicks.
   

Cleaning

Clean the clipper and the blade after each use.

1. Brush off any hairs from the clipper and from around the blade.
   
2. Brush off the hairs from the blade edge.
   
3. Brush the hairs out from between the stationary blade and the moving blade while pressing down on the cleaning lever to raise the moving blade.
   

Lubrication

• Apply the oil to the clipper before and after each use. Apply a drop of the oil to each indicated point. Failure to apply the oil may cause the following problems due to rust, wear or burn out.
  
  • The clipper has become blunt.
  • Shorter operating time.
  • Louder sound.

► Replacement parts
Replacement part is available at your dealer or Service Center

Replacement parts for ER‑GP80

Blade

WER9900

Cleaning the charging stand

Use the cleaning brush to clean hair trimmings and dust in the charging plug or in the hole on the bottom surface.

Troubleshooting

Problem	Action
The unit has become blunt	Charge the clipper.
	Clean the blade and apply oil.
	Replace the blade.
The unit stopped functioning	Charge the clipper. Or use with the AC operation.
The device cannot be charged	Push the main body into the charging stand or appliance plug all the way.
	Charge within the recommended charging temperature of 10°C (50°F) to 35°C (95°F).
Clipper can be used for only about 10 minutes even after charging	Have the battery replaced by an authorized service center.
Makes a loud sound	Confirm that the blade is properly attached.

If the problems still cannot be solved, contact the store where you purchased the unit or a service center authorised by Panasonic for repair.

Frequently asked questions

Question	Answer
Will the battery deteriorate if not used for an extended period of time?	The battery will deteriorate if not used for over 6 months, so make sure to perform a full charge at least once every 6 months.
Can the battery be charged before every use?	The clipper uses a lithium ion battery, with the charging current controlled, so there is no problem with battery life.

Removing the built-in rechargeable battery

ATTENTION:
A lithium ion battery that is recyclable powers the product you have purchased. Please call 1‑800‑8‑BATTERY for information on how to recycle this battery.

Remove the built-in rechargeable battery before disposing the clipper.
This figure must only be used when disposing the clipper, and must not be used to repair it. If you dismantle the clipper yourself, it may cause malfunction.

• Remove the clipper from the AC adaptor.
• Press the power switch to turn on the power and then keep the power on until the battery is completely discharged
• Perform steps to and lift the battery, and then remove it.
  
• Take care not to short circuit the positive and negative terminals of the removed battery, and insulate the terminals by applying tape to them.

Specifications

Power source	See the name plate on the AC adaptor.
Motor voltage	3.6 V
Charging time	Approx. 1 hour

Safety precautions

To reduce the risk of injury, loss of life, electric shock, fire, and damage to property, always observe the following safety precautions.

Explanation of symbols

The following symbols are used to classify and describe the level of hazard, injury, and property damage caused when the denotation is disregarded and improper use is performed.

	Denotes a potential hazard that will result in serious injury or death.
	Denotes a potential hazard that could result in serious injury or death.
	Denotes a hazard that could result in minor injury.

The following symbols are used to classify and describe the type of instructions to be observed.

	This symbol is used to alert users to a specific operating procedure that must not be performed.
	This symbol is used to alert users to a specific operating procedure that must be followed in order to operate the unit safely.

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions are required to always be followed, including the following.
Read all instructions before using (this appliance)

To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water. Unplug immediately.
2. Do not use while bathing or in a shower.
3. Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
4. Except when charging, always unplug this appliance from the electrical outlet immediately after using.
5. Unplug this appliance before cleaning.

To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Close supervision is required when this appliance is used by, on, or near children or invalids.
2. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
3. Never operate this appliance when it has a damaged cord or plug, when it is not working properly, after it has been dropped or damaged, or after it has been dropped into water. Return the appliance to a service center for examination and repair.
4. Keep the cord away from heated surfaces.
5. Never drop or insert any object into any opening.
6. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
7. Do not use this appliance with a damaged or broken comb, as it has the potential to result in facial injury.
8. Always attach plug to appliance first, then to outlet. To disconnect, turn all controls to "off" then remove plug from outlet.

SAVE THESE INSTRUCTIONS

Do not connect or disconnect the adaptor to a household outlet with a wet hand.

• Doing so may cause electric shock or injury.

Never use the appliance if the AC adaptor is damaged or if the power plug fits loosely in a household outlet.
Do not damage or modify, or forcefully bend, pull, or twist the cord.
Also, do not place anything heavy on or pinch the power cord.

• 
  Doing so may cause electric shock or fire due to a short circuit.

Do not use in a way exceeding the rating of the household outlet or the wiring.

• Exceeding the rating by connecting too many plugs to one household outlet may cause fire due to overheating.

This product has a built-in rechargeable battery. Do not throw into flame or heat. Do not charge, use, or leave in high temperatures.

• Doing so may cause overheating, ignition, or explosion.

Do not modify or repair.

• 
  Doing so may cause fire, electric shock, or injury. Contact an authorized service center for repair (battery change, etc.).

Never disassemble except when disposing of the product.

• 
  Doing so may cause fire, electric shock, or injury.

Do not immerse appliance in water or wash it with water.
Do not place the appliance over or near water filled sink or bathtub.

• 
  Doing so may cause electric shock or fire due to a short circuit.

Keep the appliance dry.

Do not use anything other than the supplied AC adaptor and charging stand. Also, do not charge any other product with the supplied AC adaptor and charging stand.

• 
  Doing so may cause burn or fire due to short circuit.

Do not store within the reach of children or infants. Do not let them use it.

• Putting the blade, and/or oil container in the mouth may cause accidents and injury.

Always ensure the appliance is operated on an electric power source matched to the rated voltage indicated on the AC adaptor. Fully insert the adaptor.

• 
  Failure to do so may cause fire or electric shock.

Immediately stop using and remove the adaptor if there is an abnormality or malfunction.

• 
  Failure to do so may cause fire, electric shock, or injury.

<Abnormality or malfunction cases>

• The main unit or AC adaptor is deformed or abnormally hot.
• The main unit or AC adaptor smells of burning.
• There is abnormal sound during use or charging of the main unit or AC adaptor.
  • Immediately request inspection or repair at an authorized service center.

Always unplug the adaptor from a household outlet when cleaning.

• Failure to do so may cause electric shock or injury.

Regularly clean the power plug, the appliance plug and the charging plug to prevent dust from accumulating.

• Failure to do so may cause fire due to insulation failure caused by humidity.
  Disconnect the adaptor and wipe with a dry cloth.

If the oil is consumed accidentally, do not induce vomiting, drink a large amount of water, and contact a physician.
If the oil comes into contact with eyes, immediately wash thoroughly with running water, and contact a physician.

• Failure to do so may result in physical problems.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.

• Failure to do so may cause an accident or injury.

The supply cord cannot be replaced. If the cord is damaged, the AC adaptor should be scrapped.

• Failure to do so may cause an accident or injury.

Do not press the blade against the skin.
Do not use the clipper for any purpose other than hair trimming.
Do not directly apply the blades on ears or rough skin (such as swellings, injuries or blemishes).

• Doing so may cause skin injury.

Do not allow pins or trash to adhere to the power plug or the appliance plug.

• 
  Doing so may cause electric shock or fire due to a short circuit.

Do not drop or subject to shock.

• Doing so may cause injury.

Do not wrap the cord around the adaptor or the charging stand when storing.

• Doing so may cause the wire in the cord to break with the load, and may cause fire due to short circuit.

Check that the blades are not damaged or deformed before use.

• Failure to do so may cause skin injury.

Disconnect the adaptor from the household outlet when not using.

• 
  Failure to do so may cause electric shock or fire due to electrical leakage resulting from insulation deterioration.

Disconnect the adaptor or the appliance plug by holding onto the adaptor or the appliance plug instead of the cord.

• Failure to do so may cause electric shock or injury.

► Handling of the removed battery when disposing
The rechargeable battery is exclusively for use with this clipper. Do not use the battery with other products. Do not charge the battery after it has been removed from the product.

• Do not throw into fire or apply heat.
• Do not hit, disassemble, modify, or puncture with a nail.
• Do not let the positive and negative terminals of the battery get in contact with each other through metallic objects.
• Do not carry or store the battery together with metallic jewellery such as necklaces and hairpins.
• Do not use or leave the battery where it will be exposed to high temperatures, such as under direct sunlight or near other sources of heat.
• Never peel off the tube.
  • Doing so may cause overheating, ignition, or explosion.

After removing the rechargeable battery, do not keep it within reach of children and infants.

• The battery will harm the body if accidentally swallowed.
  If this happens, consult a physician immediately.

If the battery fluid leaks out, do not touch the battery with your bare hands.

• The battery fluid may cause blindness if it comes in contact with your eyes.
  Do not rub your eyes. Wash immediately with clean water and consult a physician.
• The battery fluid may cause inflammation or injury if it comes in contact with the skin or clothes.
  Wash it off thoroughly with clean water and consult a physician.

Personal Care & Beauty Care Products

FOR USA ONLY
If you are dissatisfied with any Panasonic Personal Care & Beauty Care Products for any reason, simply return it to the place of purchase with a dated proof of purchase, in the original packaging, with all accessories, parts and instructions, within 30 days of the date of purchase, for a full refund, or call Panasonic at 1‑800‑338‑0552.

FOR YOUR CONVENIENCE, WE HAVE ESTABLISHED A TOLL-FREE (IN USA ONLY) NATIONAL ACCESSORY PURCHASE HOT LINE AT 1-800-332-5368.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Panasonic ER-GP80 - AC/Rechargeable Professional Hair Clipper Manual