HIKVISION DS-TMG520-H/A/B User Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Control Systems
  5. DS-TMG520-H/A/B
  6. User manual
HIKVISION DS-TMG520-H/A/B User Manual

HIKVISION DS-TMG520-H/A/B User Manual

Barrier gate
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Barrier Gate
User Manual

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION DS-TMG520-H/A/B

Summary of Contents for HIKVISION DS-TMG520-H/A/B

  • Page 1 Barrier Gate User Manual...
  • Page 2 Products described in this Document, which may include licenses obtained from third parties. ● Any part of the Document, including text, pictures, graphics, etc., belongs to Hikvision. No part of this Document may be excerpted, copied, translated, or modified in whole or in part by any means without written permission.
  • Page 3 Barrier Gate User Manual NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. ● YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY...
  • Page 4 Barrier Gate User Manual Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a hazardous situation which, if not avoided, will or could Danger result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance Caution degradation, or unexpected results.

  • Page 5: Table Of Contents

    Barrier Gate User Manual Contents Chapter 1 Introduction ....................... 1 1.1 Product Introduction ......................1 1.2 Packing List ..........................1 1.3 Barrier Gate Overview ......................2 1.4 Barrier Gate Structure ......................3 1.5 Boom Pole Overview ......................5 1.5.1 Octagonal Straight Boom Pole ................... 5 1.5.2 Boom Pole with Strip Light ..................
  • Page 6 Barrier Gate User Manual 2.4.8 Connect to Arrow Indicator ..................40 2.4.9 Connect to Strip Light ....................41 2.4.10 Connect to Warning Light ..................41 Chapter 3 Parameters Configuration ..................43 3.1 Remote Control ........................43 3.2 Set Parameters via Control Board Buttons ..............43 3.2.1 Button Description ....................

  • Page 7: Chapter 1 Introduction

    Barrier Gate User Manual Chapter 1 Introduction 1.1 Product Introduction Barrier gate (hereinafter referred to as “device”) is the entrance and exit management device to limit motor vehicle passing. It can control the boom pole automatically via parking lot management system. Or you can control the boom pole via buttons on remote controller. Barrier gate is widely applicable to toll station, parking lot, the entrance and exit of community and unit, etc.

  • Page 8: Barrier Gate Overview

    Barrier Gate User Manual Diagram Name Quantity Chuck Spindle rod screw set 4 Layer Expansion screw L-type wrench 1.3 Barrier Gate Overview Note The appearances of the devices vary with different models. The figure below just takes an example. Refer to the actual device for details.

  • Page 9: Barrier Gate Structure

    Barrier Gate User Manual Figure 1-1 Barrier Gate Overview 1.4 Barrier Gate Structure Figure 1-2 Barrier Gate Structure...
  • Page 10 Barrier Gate User Manual Table 1-2 Barrier Gate Structure Description Description Boom pole Boom pole fixing screw Chuck Spindle rod Top cover Aluminum Resistance Antenna Control box Host Transformer Machine core Air switch Strip Spring Front cover Figure 1-3 Machine Core Structure Table 1-3 Machine Core Structure Description Description...

  • Page 11: Boom Pole Overview

    Barrier Gate User Manual Description Description Spring Cotter pin Spring lower screw 1.5 Boom Pole Overview 1.5.1 Octagonal Straight Boom Pole Figure 1-4 Octagonal Straight Boom Pole Table 1-4 Octagonal Straight Boom Pole Packing List Item Quantity Octagonal Straight boom pole 1...

  • Page 12: Boom Pole With Strip Light

    Barrier Gate User Manual 1.5.2 Boom Pole with Strip Light Figure 1-5 Boom Pole with Strip Light Table 1-5 Boom Pole with Strip Light Packing List Item Quantity Boom pole with strip light 1 Cushion block...

  • Page 13: Anti-Collision Cylinder Boom Pole

    Barrier Gate User Manual 1.5.3 Anti-collision Cylinder Boom Pole Figure 1-6 Anti-collision Cylinder Boom Pole Table 1-6 Anti-collision Cylinder Boom Pole Packing List Item Quantity Anti-collision cylinder boom pole M8 cap nut M8 × 75 hex socket head cap screw 1...

  • Page 14: Octagonal Telescopic Boom Pole

    Barrier Gate User Manual 1.5.4 Octagonal Telescopic Boom Pole Figure 1-7 Octagonal Telescopic Boom Pole Table 1-7 Octagonal Telescopic Boom Pole Packing List Item Quantity Octagonal telescopic boom pole Sub-boom pole anti-fall adhesive tape 1 M4 × 20 pan head hex screw 1.5.5 Fence Boom Pole Figure 1-8 Fence Boom Pole...

  • Page 15: Folding Boom Pole

    Barrier Gate User Manual Table 1-8 Fence Boom Pole Packing List Item Quantity Fence boom pole Pull rod joint component 1 1.5.6 Folding Boom Pole Figure 1-9 Folding Boom Pole Table 1-9 Folding Boom Pole Packing List Item Quantity Sub-boom pole Main boom pole Pull rod Joint component to connect main boom pole and pull rod 1...

  • Page 16: Chapter 2 Installation

    Barrier Gate User Manual Chapter 2 Installation 2.1 Installation Environment The installation position of the barrier gate should meet the customer’s requirements and the following requirements. ● The installation space should be large enough to guarantee the boom pole can rise or fall normally.
  • Page 17 Barrier Gate User Manual Note The suggestions for positions of holes: ● The holes in vertical direction should be near to the switch. ● If the entrance/exit is unidirectional, the holes should be in the horizontal center of the refuge island. If the entrance/exit is bi-directional, the holes in the horizontal direction should be far away from the entrance/exit.

  • Page 18: Install Boom Pole

    Barrier Gate User Manual 2) Put the host on the positions of expansion screws on the refuge island to make the screws pass through the layers. Keep the layers perpendicular to the barrier gate’s switch. 3) Fasten the expansion nuts on the screws to fix the host. Figure 2-4 Fix Host Danger Keep the supporting bracket of the boom pole vertically upward to avoid accident caused by...
  • Page 19 Barrier Gate User Manual Figure 2-6 Install Chuck 3. Install the boom pole to the spindle rod and fasten the other ends of the bolts with the disassembled spring washers, flat washers, and cap nuts. Figure 2-7 Fix Octagonal Straight Boom Pole...

  • Page 20: Install Boom Pole With Strip Light

    Barrier Gate User Manual 2.3.2 Install Boom Pole with Strip Light Steps 1. Unscrew the cap nuts, spring washers, and flat washers on the other sides of the four assembling bolts. Save the components and parts for the following installations. Figure 2-8 Unscrew Assembling Bolts 4.
  • Page 21 Barrier Gate User Manual Figure 2-10 Fix Boom Pole with Strip Light 6. Remove the rubber plug of the cable hole on the host. Figure 2-11 Remove Rubber Plug 7. Wire the strip light cable. 1) Take the M12 white waterproof joint out from the accessory package. 2) Fix the waterproof joint to the cable hole on the host with the fixing nut.

  • Page 22: Install Anti-Collision Cylinder Boom Pole

    Barrier Gate User Manual waterproof cover, waterproof joint, and fixing nut. 4) Pull the strip light cable in the internal host until the white rolling strip limit block on the strip light cable nears to the waterproof cover. 5) Power off the device. Rotate the boom pole to check if the strip light cable length is appropriate.
  • Page 23 Barrier Gate User Manual Figure 2-13 Stuff Boom Pole Aslant 2. Insert the M8 × 75 hex socket head cap screw into the installation hole, and push the boom pole into the spindle rod quickly according to the directions as shown in the figure below. Figure 2-14 Install Anti-collision Cylinder Boom Pole 3.

  • Page 24: Install Octagonal Telescopic Boom Pole

    Barrier Gate User Manual Figure 2-15 Fix Boom Pole 2.3.4 Install Octagonal Telescopic Boom Pole Steps 1. Install the octagonal telescopic boom pole. 1) Pull the sub-boom pole out according to the direction shown in the figure below. Align the installation holes on the main boom pole and sub-boom pole.
  • Page 25 Barrier Gate User Manual Figure 2-17 Fix Screws 3) Remove the end cover of the sub-boom pole. Insert the anti-fall adhesive tape into the sub-boom pole. After the anti-fall adhesive tape is inserted to the limit position, cut the projecting adhesive tape. Figure 2-18 Insert Anti-Fall Adhesive Tape 4) Install the end cover to the sub-boom pole.
  • Page 26 Barrier Gate User Manual 2) Install the chuck to the boom pole with the bolts as shown in the figure below. Figure 2-21 Install Chuck 3) Install the boom pole to the spindle rod and fasten the other ends of the bolts with the disassembled spring washers, flat washers, and cap nuts.

  • Page 27: Install Fence Boom Pole

    Barrier Gate User Manual 2.3.5 Install Fence Boom Pole Installation Procedure Steps 1. Install the pull rod joint component to the installation position of the host. Unfasten the joint component pull rod. Figure 2-23 Install Pull Rod Joint Component 2. Install the fence boom pole. 1) Unscrew the cap nuts, spring washers, and flat washers on the other sides of the four assembling bolts.
  • Page 28 Barrier Gate User Manual Figure 2-25 Install Chuck 3) Install the boom pole to the spindle rod and fasten the other ends of the bolts with the disassembled spring washers, flat washers, and cap nuts.
  • Page 29 Barrier Gate User Manual Figure 2-26 Fix Fence Boom Pole to Spindle Rod 4) Power off the device. Pull the fence boom pole to the horizontal position. Connect the pull rod of the joint component to the joint 2 of the fence boom pole pull rod. Wrest the pull rod of the joint component until the center boom poles are in the vertical position.

  • Page 30: Install Folding Boom Pole

    Barrier Gate User Manual Figure 2-27 Adjust Fence Boom Pole Note For the refuge island with a special height, drill holes by yourself to adjust the buffer rod height. Left and Right Directions of Fence Boom Pole When you look from the arrow direction as shown below, the right fence boom pole is the one that the center boom poles are on the left of the main boom pole, and the left fence boom pole is the one that the center boom poles are on the right of the main boom pole.
  • Page 31 Barrier Gate User Manual components and parts for the following installations. Figure 2-29 Unfasten Accessories of Main Boom Pole 2) Unfasten the cap nuts on the sub-boom pole and remove the screw, gaskets, and sub- boom pole pull rod joint. Save the components and parts for the following installations. Figure 2-30 Unfasten Accessories of Sub- Boom Pole 3) Force apart the sub-boom pole joint boards, and install the main boom pole.
  • Page 32 Barrier Gate User Manual can clip into installation holes on the sub-boom pole joint boards. Figure 2-32 Install Sub-Boom Pole Pull Rod Joint 2. Install the folding boom pole to the host. Note Here we take example of the right direction barrier gate. 1) Remove the plastic nut on the installation position of the right direction main boom pole pull...
  • Page 33 Barrier Gate User Manual rod joint. Figure 2-33 Remove Plastic Nut 2) Install the right direction main boom pole pull rod joint to the installation holes with the flat washer and spring washer. Figure 2-34 Install Main Boom Pole Pull Rod Joint 3) Unscrew the cap nuts, spring washers, and flat washers on the other sides of the four assembling bolts.
  • Page 34 Barrier Gate User Manual Figure 2-35 Unscrew Assembling Bolts 4) Install the chuck to the boom pole with the bolts as shown in the figure below. Figure 2-36 Install Chuck 5) Install the boom pole to the spindle rod and fasten the other ends of the bolts with the disassembled spring washers, flat washers, and cap nuts.
  • Page 35 Barrier Gate User Manual Figure 2-37 Fix Folding Boom Pole 6) Power off the device. Pull the main boom pole to the horizontal position, and place the sub- boom pole nearly to the horizontal position. Wrest the pull rod between the sub-boom pole pull rod joint and the main boom pole pull rod joint.

  • Page 36: Wiring

    Barrier Gate User Manual both ends. Figure 2-38 Connect Boom Pole to Host via Pull Rod 2.4 Wiring 2.4.1 Connect to Power Supply Connect the laid power cord (RVV3 × 1.5 mm or above) to the power input of barrier gate. Install the top and front covers.

  • Page 37: Connect To Access Anpr Camera

    Barrier Gate User Manual Figure 2-39 Connect to Power Supply 2.4.3 Connect to Access ANPR Camera As the figure shown below, connect the rising control + and rising control – interfaces of the barrier gate to the rising control interfaces of the access ANPR camera, and connect the falling control + and falling control –...

  • Page 38: Connect To Traffic Signal Light

    Barrier Gate User Manual Resistance Motor Network AC34V Nixie Connection Encoder Connection Interface Tube Barrier Gate Control Box Rise Stop Fall Learn Falling Control Access ANPR Rising camera Control Figure 2-40 Connect to Access ANPR Camera 2.4.4 Connect to Traffic Signal Light Connect the live line to the COM interface of the barrier gate.

  • Page 39: Connect To Anti-Fall Radar

    Barrier Gate User Manual Connect to Red Light Connect to Green Light Null Line Incoming Live Line Live Line Resistance Motor Network AC34V Nixie Connection Encoder Connection Interface Tube Barrier Gate Control Box Rise Stop Fall Learn Figure 2-41 Connect to Traffic Signal Light Note The maximum allowable voltage for the interfaces of red and green lights is 240 VAC or 100 VDC.
  • Page 40 Barrier Gate User Manual Resistance Motor Network AC34V Nixie Connection Encoder Connection Interface Tube Barrier Gate Control Box Rise Stop Fall Learn Anti-fall Radar Figure 2-42 Connect to Anti-fall Radar Note ● Radar 12 V power supply output: 0.5 AAV, max. 1 A. ●...
  • Page 41 Barrier Gate User Manual Figure 2-43 Small-Sized Vehicles Scenario Scenario 2: Large-Sized Vehicles For large-sized vehicles, such as the oil tank trucks, transport vehicles, trucks, and other vehicles with chassises of higher than 1 m, install the radar according to the figure shown below.
  • Page 42 Barrier Gate User Manual Figure 2-44 Large-Sized Vehicles Scenario Scenario 3: Mixed Traffic For mixed traffic scenario, such as the large-sized and small-sized vehicles are mixing, install the radar according to the figure shown below.

  • Page 43: Connect To Vehicle Detector

    Barrier Gate User Manual Figure 2-45 Mixed Traffic Scenario 2.4.6 Connect to Vehicle Detector Vehicle Detector Wiring Connect the Induction input + and Induction input - interfaces of the barrier gate to the vehicle detector.
  • Page 44 Barrier Gate User Manual Resistance Motor Network AC34V Nixie Connection Encoder Connection Interface Tube Barrier Gate Control Box Rise Stop Fall Learn Loop Vehicle Detector Figure 2-46 Connect to Vehicle Detector Vehicle Detector Installation Instructions The general width of the vehicle detector is 1 m. If there are large-sized vehicles passing in the scenario, widen the width to 1.5 m.

  • Page 45: Connect To Active Infrared Intrusion Detector

    Barrier Gate User Manual Figure 2-47 Vehicle Detector Installation 2.4.7 Connect to Active Infrared Intrusion Detector Connect the induction input - interface of the barrier gate to the COM interface of the active infrared intrusion detector, and the induction input + interface of the barrier gate to the OUT interface of the active infrared intrusion detector.

  • Page 46: Connect To Arrow Indicator

    Barrier Gate User Manual Resistance Motor Network AC34V Nixie Connection Encoder Connection Interface Tube Barrier Gate Control Box Rise Stop Fall Learn Figure 2-48 Connect to Active Infrared Intrusion Detector 2.4.8 Connect to Arrow Indicator Connect the arrow indicator to the barrier gate as shown below. 箭头灯接线...

  • Page 47: Connect To Strip Light

    Barrier Gate User Manual Figure 2-49 Connect to Arrow Indicator 2.4.9 Connect to Strip Light For the boom pole with strip light, connect the strip light to the barrier gate as shown below. Yellow Green Red Line Resistance Motor Network AC34V Nixie Connection...
  • Page 48 Barrier Gate User Manual Resistance Motor Network AC34V Nixie Connection Encoder Connection Interface Tube Barrier Gate Control Box Rise Stop Fall Learn Warning Light Wire Figure 2-51 Connect to Warning Light...

  • Page 49: Chapter 3 Parameters Configuration

    Barrier Gate User Manual Chapter 3 Parameters Configuration After the installation completes, power on the barrier gate, and it will operate self-check of rising to limit position. After the self-check completes, you can control the barrier gate via remote controller or buttons. 3.1 Remote Control After the self-check completes, you can control the boom pole to rise, fall, and stop via the remote controller leaving factory with the barrier gate.

  • Page 50: Operation Procedure

    Barrier Gate User Manual 3.2.2 Operation Procedure Refer to the table below for the description of the value on the nixie tube. Table 3-1 Nixie Tube Value Description Value Description To enable manual learning. Refer to Set Manual Learning for details. To adjust the rising/falling limit position of the boom pole.
  • Page 51 Barrier Gate User Manual Press the Rise button on the remote controller, press the Rise button on the Rising Limit control board, or power on the device to Position adjust the boom pole to the rising limit position. Hold the Learn button on the control board. Hold the Learn button on the control board.
  • Page 52 Barrier Gate User Manual Press the Rise button on the remote controller, press the Rise button on the Rising Limit control board, or power on the device to Position adjust the boom pole to the rising limit position. Hold the Learn button on the control board. Press the Rise/Fall button on the control board to increase/decrease the value...
  • Page 53 Barrier Gate User Manual Press the Fall button on the remote Falling Limit controller or press the Fall button on the Position control board to adjust the boom pole to the falling limit position. Hold the Learn button on the control board. Hold the Rise/Fall button on the control board to adjust the boom pole to the falling limit position.
  • Page 54 Barrier Gate User Manual Press the Rise button on the remote controller, press the Rise button on the Rising Limit control board, or power on the device to Position adjust the boom pole to the rising limit position. Hold the Learn button on the control board. Press the Rise/Fall button on the control board to increase/decrease the value...
  • Page 55 Barrier Gate User Manual Press the Rise button on the remote controller, press the Rise button on the Rising Limit control board, or power on the device to Position adjust the boom pole to the rising limit position. Hold the Learn button on the control board. Press the Rise/Fall button on the control board to increase/decrease the value...
  • Page 56 Barrier Gate User Manual Press the Rise button on the remote controller, press the Rise button on the Rising Limit control board, or power on the device to Position adjust the boom pole to the rising limit position. Hold the Learn button on the control board. Press the Rise/Fall button on the control board to increase/decrease the value...
  • Page 57 Barrier Gate User Manual Press the Rise button on the remote controller, press the Rise button on the Rising Limit control board, or power on the device to Position adjust the boom pole to the rising limit position. Hold the Learn button on the control board. Press the Rise/Fall button on the control board to increase/decrease the value...
  • Page 58 Barrier Gate User Manual Press the Rise button on the remote controller, press the Rise button on the Rising Limit control board, or power on the device to Position adjust the boom pole to the rising limit position. Hold the Learn button on the control board. Press the Rise/Fall button on the control board to increase/decrease the value...
  • Page 59 Barrier Gate User Manual Press the Rise button on the remote controller, press the Rise button on the Rising Limit control board, or power on the device to Position adjust the boom pole to the rising limit position. Hold the Learn button on the control board. Press the Rise/Fall button on the control board to increase/decrease the value...
  • Page 60 Barrier Gate User Manual Press the Rise button on the remote controller, press the Rise button on the Rising Limit control board, or power on the device to Position adjust the boom pole to the rising limit position. Hold the Learn button on the control board. Press the Rise/Fall button on the control board to increase/decrease the value...
  • Page 61 Barrier Gate User Manual Press the Rise button on the remote controller, press the Rise button on the Rising Limit control board, or power on the device to Position adjust the boom pole to the rising limit position. Hold the Learn button on the control board. Press the Rise/Fall button on the control board to increase/decrease the value...
  • Page 62 Barrier Gate User Manual Press the Rise button on the remote controller, press the Rise button on the Rising Limit control board, or power on the device to Position adjust the boom pole to the rising limit position. Hold the Learn button on the control board. Press the Rise/Fall button on the control board to increase/decrease the value...
  • Page 63 Barrier Gate User Manual Value Boom Pole Type 4 m straight boom pole 5 m straight boom pole 6 m straight boom pole 3 m fence boom pole 4 m fence boom pole 5 m fence boom pole 3 m folding boom pole 4 m folding boom pole 5 m folding boom pole 3 m boom pole with strip light...

  • Page 64: Chapter 4 Maintenance

    Barrier Gate User Manual Chapter 4 Maintenance 4.1 Adjust Boom Pole Balance Adjust the balance of the boom pole. Steps 1. Cut off the power supply. Rotate the hand wheel of the machine core to raise the boom pole to the position where the angle between the boom pole and the ground surface is 20°...

  • Page 65: Change Spindle Rod And Spring

    Barrier Gate User Manual 2. Disassemble the boom pole and chuck. 3. Repeat the boom pole installation procedure to install a new boom pole. Figure 4-2 Change Boom Pole 4.3 Change Spindle Rod and Spring 4.3.1 Spring and Spindle Rod Specifications If you need to change the boom pole, prepare the corresponding springs and spindle rods according to the boom pole types.

  • Page 66: Change Spindle Rod

    Barrier Gate User Manual Spring with white hook × 1 Large octagonal boom pole 6 m large octagonal spindle rod boom pole Spring with red hook × 1 Small octagonal boom pole 1.5 m + 1.5 m folding Spring with white hook × 1 spindle rod boom pole Spring with green hook ×...
  • Page 67 Barrier Gate User Manual assembling bolts. Save the components and parts for the following installations. 2. Disassemble the boom pole and chuck. Figure 4-3 Disassemble Boom Pole and Chuck 3. Unscrew the M12 fixing bolt of the spindle rod anticlockwise with a 10 mm hex wrench, and disassemble the bolt.

  • Page 68: Change Spring

    Barrier Gate User Manual Figure 4-5 Disassemble Control Box 6. Disassemble the spindle rod and change a new one. Install the M12 fixing bolt of the spindle rod, and fasten it with a torque no smaller than 60 NM. Figure 4-6 Change Spindle Rod Fix the M8 ×...
  • Page 69 Barrier Gate User Manual Steps 1. Close the cotter pin openings with needle-nose pliers. Figure 4-8 Close Cotter Pin Openings 2. Pull the cotter pins out with needle-nose pliers. Figure 4-9 Pull Cotter Pins Out...
  • Page 70 Barrier Gate User Manual 3. Hold the upper screw weld nuts with an adjustable wrench, and then unscrew the two bottom lock nuts with another adjustable wrench. Figure 4-10 Unscrew Lock Nut 4. Adjust the boom pole of the barrier gate to the falling status to keep the three points shown in the figure below in a straight line, and then the spring and spring shaft are lifted.

  • Page 71: Change Machine Core

    Barrier Gate User Manual Figure 4-12 Change Spring 6. Install the new spring according to the steps above reversely. 4.4 Change Machine Core Before you start Cut off the power supply. Disassemble the boom pole and spindle rod according to the procedure above.

  • Page 72: Left/Right Direction Of Boom Pole

    Barrier Gate User Manual Figure 4-13 Remove Motor Wire 2. Remove the M8 hex socket head cap screws of the machine core with a No. 6 hex wrench. 3. Disassemble the machine core and change a new one. 4. Fix the machine core with the M8 hex socket head cap screws, put motor wire into the wire slot, connect the power cord and signal line terminals, and then fix the grounding terminal.
  • Page 73 Barrier Gate User Manual Figure 4-15 Boom Pole Direction Instruction...

  • Page 74: Change Left/Right Direction Of Machine Core

    Barrier Gate User Manual 4.6 Change Left/Right Direction of Machine Core Before you start Cut off the power supply. Disassemble the boom pole and spindle rod according to the procedure above. Steps 1. Use a cross screwdriver to remove the grounding terminal of the motor wire, and then unplug the motor power cord and signal line terminals on the barrier gate control board.
  • Page 75 Barrier Gate User Manual Figure 4-17 Change Machine Core Direction 4. Fix the machine core with the M8 hex socket head cap screws, put motor wire into the wire slot, connect the power cord and signal line terminals, and then fix the grounding terminal. Figure 4-18 Fix Machine Core 5.

  • Page 76: Faq

    Barrier Gate User Manual A. FAQ When the barrier gate is abnormal, open the top cover, and observe the fault code on the nixie tube to troubleshoot. Code Description ● The barrier gate was hit. ● The boom pole does not match. ●...
  • Page 77 Barrier Gate User Manual Code Description short-circuited. FOC timeout. The software is abnormal. ● The braking resistor was damaged or not inserted firmly. ● The control box was damaged. The signal cable was not connected well. If the device fail to rise to the limit position, but the motor is running well, the system will reboot if it receives the rise command.

  • Page 78: Peripheral Device Interfaces Introduction

    Barrier Gate User Manual B. Peripheral Device Interfaces Introduction Open the top cover of host, and you can see the interfaces as shown below. Figure B-1 Interfaces Table B-1 Interface Description Max. Max. Name Description Voltage Current Connects to the red traffic signal AC 240 V/ Red Light light.
  • Page 79 Barrier Gate User Manual Max. Max. Name Description Voltage Current RS485-A2 Connects to the remote receiving module. RS485-B2 RS485-A Inputs RS-485 control signals. A RS485-B connects to RS-485 +, and B connects to RS-485 -. +12V Connects to 12 V power supply. ●...
  • Page 80 Barrier Gate User Manual Max. Max. Name Description Voltage Current Bollard Control 1 + DC 24 V Bollard Control 1 - Bollard Control 2 + Bollard Control 2 - Reserved interfaces. Alarm Input 1 + DC 12 V Alarm Input 1 - Alarm Input 2 + Alarm Input 2 -...
  • Page 81 UD28917B-B...

This manual is also suitable for:

Ds-tmg520-m/a/b

Table of Contents