Do not operate the crown or buttons while ー retailer or to an authorized CASIO service Example of Daily Use your watch is submersed in water or wet. center. Hand washing, rain Avoid wearing your watch while in the ー ...
Page 3
Watch Operation Guide 3495 Temperature Chemicals Leather Band ● ● ● Never leave your watch on the dashboard Do not allow your watch to come into Allowing your watch to remain in contact ● ● ● of a car, near a heater, or in any other contact with thinner, gasoline, solvents, with other items or storing it together with location that is subject to very high...
If you ever notice any abnormality immediately stop using your watch and take it to your original retailer or to an authorized CASIO service center. Even if the surface of the metal appears ●...
Watch Operation Guide 3495 General Guide Indicators Before Getting Started... ① ② ① ④ This section provides an overview of the watch ② ⑤ and introduces convenient ways it can be ③ ⑥ used. ⑦ Watch Features ● Solar Charging ●...
Watch Operation Guide 3495 Checking the Charge Level Navigating Between Modes ● Charging A display indicator shows the watch’s current Press (C) to cycle between modes. This watch runs on power supplied from a charge level. In any mode, hold down (C) for at least one rechargeable (secondary) battery that is ●...
Watch Operation Guide 3495 Viewing the Face in the Dark Note Note The watch has a light that illuminates the face When [H], [M], and [L] are all flashing Actual charging time depends on the ● ● for viewing in the dark. on the display, it means that all local charging environment.
Watch Operation Guide 3495 Specifying the Illumination Duration ● Time Adjustment Important! You can select either 1.5 seconds or three seconds as the illumination duration. Auto Light may not operate properly ● Your watch can receive time calibration when the watch is at a horizontal angle Enter the Timekeeping Mode.
Watch Operation Guide 3495 Appropriate Signal Reception Time Signal Reception Ranges Auto Time Calibration Signal Location Receive Time calibration signal reception is supported in the areas shown below. A time calibration signal can be received while An automatic time calibration signal receive the watch is near a window.
Watch Operation Guide 3495 Note Note Press (C) 13 times. This causes [On] or [OFF] to flash on the The receive operation typically takes Even if there was a successful receive ● ● display. anywhere from about three minutes to operation, [RCVD] will not be about eight minutes.
Watch Operation Guide 3495 Using Watch Operations to Note Keep pressing (C) until the setting you Adjust the Time Setting want to change is flashing. The [AUTO] summer time setting is ● Each press of (C) moves the flashing to ●...
Watch Operation Guide 3495 World Time Configure the date and time settings. Press (D) to toggle the setting between [12H] (12-hour timekeeping) and [24H] To reset the seconds to 00: Press (D). ● (24-hour timekeeping). 1 is added to the minutes when the You can view the current time in 48 cities (31 current count is between 30 and 59 time zones), and UTC (Coordinated Universal...
Watch Operation Guide 3495 World Time City Setting Alarm Note You can specify up to five cities as your World While the setting is being configured, ● Time favorites. If you are in an area that The watch will beep when the alarm time is the watch will exit the setting operation observes summer time, you can also enable reached.
Watch Operation Guide 3495 Configuring the Hourly Time Use (B) and (D) to change the hour setting. Enter the Alarm Mode. Signal Setting Navigating Between Modes Holding down (B) or (D) scrolls through ● settings at high speed. Use (D) to display the item whose on/off Enter the Alarm Mode.
Watch Operation Guide 3495 Measuring a Split Time Timing the First and Second Stopwatch Place Finishers Enter the Stopwatch Mode. The stopwatch can measure elapsed time up Navigating Between Modes Enter the Stopwatch Mode. to 23 hours, 59 minutes, 59 seconds (24 Navigating Between Modes hours).
Watch Operation Guide 3495 Timer Other Settings Press (C). This causes the seconds digits to flash. The timer counts down from a start time This section explains other watch settings you specified by you. A beeper sounds when the can configure. end of the countdown is reached.
Watch Operation Guide 3495 Specifying the Day of the Enabling the Button Configuring Power Saving Week Language Operation Tone Function Settings You can select any one of six languages for Use the procedure below to enable or disable Enter the Timekeeping Mode. the day of the week display in the Timekeeping the tone that sounds when you press a button.
Watch Operation Guide 3495 Other Information Stopwatch : City Offset ST. JOHN’S * St. John’s -3.5 Measurement units 1/100 seconds (first hour); 1 second BUENOS AIRES Buenos Aires This section provides non-operational (after first hour) RIO DE JANEIRO Rio de Janeiro information you also need to know.
The time for a World Time City is not Visit the website below. day settings manually. correct. https://world.casio.com/support/ The summer time setting (standard time/ summer time) is wrong. World Time City Setting Alarm The alarm does not sound.