Table of Contents
Advertisement
Connecting example: AV equipment
For <HDMI IN 1> / <HDMI IN 2> terminals
Note
f When HDMI signal is input, switching of the setting in the [DISPLAY OPTION] menu → [HDMI IN] → [HDMI1] / [HDMI2] → [EDID SELECT]
may be required depending on the connected external device or the input signal.
f For the HDMI cable, use an HDMI High Speed cable that conforms to the HDMI standards. However, when the following 4K image signal
exceeding the supported transmission speed of the HDMI High Speed cable is to be input, use the HDMI cable supporting the high speed
transmission of 18 Gbps such as the one with Premium HDMI cable authentication.
g An image signal with high specification color depth and gradation such as 3840 x 2160/60p 4:2:2/36-bit or 3840 x 2160/60p 4:4:4/24-bit
Images may be disrupted or may not be projected when an image signal exceeding the supported transmission speed of the HDMI cable is
input.
f The <HDMI IN 1> / <HDMI IN 2> terminals of the projector can be connected to an external device equipped with a DVI-D terminal using an
HDMI/DVI conversion cable. However, this may not function properly for some external devices, and image may not be projected.
For <SDI 1 IN> / <SDI 2 IN> / <SDI 3 IN> / <SDI 4 IN> / <SDI OUT> terminals of the Function Board
This is an example when the optional 12G-SDI Terminal Board (Model No.: TY-SB01QS) is installed in <SLOT>.
12G-SDI signal output compatible device
Note
f Use a cable of 5C-FB or higher (such as 5C-FB or 7C-FB) to properly transmit images when transmitting the HD-SDI signal or the 3G-SDI
signal. It is recommended to use a cable of L-5.5CUHD manufactured by Canare Electric Co., Ltd. when transmitting the 12G-SDI signal.
f The maximum cable length that can be used is as follows. However, this maximum cable length is a rough guideline, and does not
guarantee the transmission distance.
g Input and output of HD-SDI signal and 3G-SDI signal: 100 m (328'1")
g Input of 12G-SDI signal: 80 m (262'6") (when using a cable of L-5.5CUHD), 20 m (65'7") (when using a cable of 5C-FB)
g Output of 12G-SDI signal: 50 m (164'1") (when using a cable of L-5.5CUHD), 20 m (65'7") (when using a cable of 5C-FB)
f Use the BNC connector that is compatible with the coaxial cable and type of the signal to be used.
f Setting the [DISPLAY OPTION] menu → [SLOT IN] is required depending on the connected external device or the input signal.
f The <SDI OUT> terminal is an active through terminal to output the SDI signal (HD-SDI/3G-SDI/12G-SDI) input to the <SDI 1 IN> terminal.
f The <SDI 2 IN> / <SDI 3 IN> / <SDI 4 IN> terminals are used when the quad link signal is input. These terminals do not support input of
12G-SDI signal.
f To input the quad link signal, use the cable with same length and same type for connecting to each of <SDI 1 IN> / <SDI 2 IN> / <SDI 3 IN>
/ <SDI 4 IN> terminals. The image may not be projected correctly when the difference of the cable length is 4 m (13'1") or more.
60 - ENGLISH
Chapter 2 Getting Started — Connecting
Blu-ray disc player
4 IN
4 IN
3 IN
3 IN
2 IN
2 IN
OUT
OUT
1 IN
1 IN
TY-SB01QS
TY-SB01QS
3G SDI
3G SDI
12G/3G SDI
12G/3G SDI
HD-SDI signal, 3G-SDI signal, 12G-SDI signal
4 IN
4 IN
3 IN
3 IN
2 IN
2 IN
OUT
OUT
1 IN
1 IN
TY-SB01QS
TY-SB01QS
12G/3G SDI
12G/3G SDI
3G SDI
3G SDI
Advertisement
Table of Contents
