Advertisement
To Adjust
the
Blades
for
Proper Alignment
Unplug
the
planer.
1.
Loosen
the three hex
head bolts
and
with blade
installed
in
the
drum,
ad-
vance blade
until
it
slightly
extends
above the stationary shoe. See Fig.
15.
2.
Lightly tighten
the 3
hex head
screws
and rotate drum to insure blade
is
prop-
erly spaced. This assures clearance of
blade
to
housing.
Blade must
be
clamped loosely, but free
to
adiust
to
proper
position.
3.
Place the
clear plastic gauge
on the
sta-
tionary
shoe
as
illustrated
in
Fig.
15,
holding gauge
firmly
against stationary
shoe. NOTE: Clear
plastic gauge
must
not
touch
adjustable
shoe.
4.
Rotate blade and drum as
illustrated
in
Fig.
15. Always
turn blade
in
direction
shown. As
the
blade sweeps
Past the
gauge
block,
it will
be adjusted
auto-
matically.
NEVER
TOUCH
BLADES.
Check, the blade
must be
llush and par-
allel
to
stationary
shoe.
5.
Remove
gauge
and
alternately tighten
3
hex head bolts gradually until
secure.
This procedure
prevents misalignment
of
blade
due
to
clamping forces.
6.
Continue procedure
with blade
#2.
7.
Before you
use
the
tool, adjust
knob
to
0
cutting depth. Place
Planer
on
a
wooden surface.
ln
case
the
blade
should
remove some material
or
the
planer vibrates
intermittently,
please
repeat
the
adjustments
of the
blade
once
more.
ACCESSORTES
BLADE
TO
EXTEND
SLIGHTLY
ABOVE
STATIONARY
SHOE
WHEN
ADJUSTING
-
ADJUSTABLE
SHOE
STATIONARY
SHOE
GUIDE
BAR_DO
NOT
REMOVE
WHEN
CHANGING
BLADES
GAUGE SHOULD NOT
TOUCH
ADJUSTABLE
SHOE
8.
Before
doing any finish work, make
a
few cuts
on
scrap
lumber
to
assure
blades
are
properly adjusted.
NOTE:
Recommended accessories for
this tool
are listed in
this
manual
and
in Black
&
Decker catalogs.
The
use
of
any
other
accessory may
be
hazardous.
337Ct1
-Double
edge carbide
tipped
blades.
33702
-Adlustable
bevel fence.
33703-Chip
collecting
hose
with
adaptor.
LUBRICATION
All ball
bearings used are
factory lubricated
to
last
the life of the
bearings.
MAINTENANCE
After every
use of
the
tool,
make sure
the
tool
is
cleaned out with
an
air
hose
and free of
all
debris.
IMPORTANT
To
assure product salety and reliability, repairs, maintenance and adjustment, (including
Oiuin
insSiection
and
r-eplacement)
dnouid be performed by Black
&
Decker
Service
Centers
or
other qualified service organizations, always using Black & Decker replace-
ment
parts.
COMMERCIAL/INDUSTRIAL
USE WARRANTY
Black & Decker warrants this product for one year from date of purchase.
We
will
repair
without charge, any
defects
due
to
faulty maierial or
workmanship.
Please return
the
complete unii, iran5portation prepaid, to
iny
Black & Decker Service
Center
or Author-
ized'Service Station'listed under
'''Tools
Eleitric"
in the
yellow
pages. This
warranty
does
not
apply to accessories or damage caused where repdirs have
been made
or attempted
by others.
BLACK
&
DECKER (U.S.)
lNC., lndustrial/Construction Division
626
Hanover Pike, Hampstead,MD
21074 U.S.A.
PRINTED IN
ITALY
Part.806610
CLEAR PLASTIC
GAUGE
Advertisement
