1. Manuals
  2. Brands
  3. Bosch Manuals
  4. IP Camera
  5. AUTODOME 7100i
  6. Installation manual

Bosch AUTODOME 7100i Installation Manual

Hide thumbs Also See for AUTODOME 7100i:
Table of Contents

Advertisement

Quick Links

Download this manual
AUTODOME 7100i│AUTODOME 7100i IR
NDP‑7602‑Z40│NDP‑7602‑Z40L│NDP‑7604‑Z12L│NDP‑7602‑Z40‑
CA│NDP‑7602‑Z40L‑CA│NDP‑7604‑Z12L‑CA
en
Installation Manual

Advertisement

Table of Contents
loading

Related Manuals for Bosch AUTODOME 7100i

Summary of Contents for Bosch AUTODOME 7100i

  • Page 1 AUTODOME 7100i│AUTODOME 7100i IR NDP‑7602‑Z40│NDP‑7602‑Z40L│NDP‑7604‑Z12L│NDP‑7602‑Z40‑ CA│NDP‑7602‑Z40L‑CA│NDP‑7604‑Z12L‑CA Installation Manual...

  • Page 3: Table Of Contents

    Connecting the AUTODOME camera to the PC 10.1 Power by midspan 10.2 Recommendations for third-party IEEE 802.3bt PoE Power Supply 10.2.1 Connecting watertight, electrically grounded metal conduit to Bosch Outdoor Midspans 10.2.2 Power by 24 VAC/36 VDC 10.3 Recommendations for 24 VAC Power Supply 10.3.1 Compatible 24 VAC Power Supplies 10.3.2...
  • Page 4 | Table of contents AUTODOME 7100i│AUTODOME 7100i IR Image flickers, streaks, or flares 11.7 No camera control 11.8 No camera operation, or operation not as expected (after exposure to extreme low temperatures) 11.9 No network connection 11.10 No video 11.11...

  • Page 5: Safety

    Legal Information Copyright This manual is the intellectual property of Bosch Security Systems, and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.

  • Page 6: Important Safety Instructions

    ® National Electrical Code (NEC)), Canadian Electrical Code, Part I (also called CE Code or CSA C22.1), and all applicable local codes. Bosch Security Systems accepts no liability for any damages or losses caused by incorrect or improper installation. Warning! INSTALL EXTERNAL INTERCONNECTING CABLES IN ACCORDANCE TO NEC, ANSI/NFPA70 (FOR US APPLICATION) AND CANADIAN ELECTRICAL CODE, PART I, CSA C22.1 (FOR CAN...
  • Page 7 Safety | en Notice! Bosch recommends the use of surge/lightning suppression devices (sourced locally) to protect network and power cables and the camera installation site. Refer to NFPA 780, Class 1 & 2, UL96A, or the equivalent code appropriate for your country/region, and to local building codes.

  • Page 8: Important Notices

    Camera signal - Protect the cable with a primary protector if the camera signal is beyond 140 feet, in accordance with NEC800 (CEC Section 60). Environmental statement - Bosch has a strong commitment towards the environment. This device has been designed to respect the environment as much as possible.
  • Page 9 AUTODOME 7100i│AUTODOME 7100i IR Safety | en Power disconnect - Units have power supplied to the unit whenever the power cord is inserted into the power source, or when IEEE 802.3bt, type 3/4 (60W/90W) power is provided over the Ethernet Cat5e/Cat6e cable. The power cord is the main power disconnect device for switching off the voltage for all units.

  • Page 10: Connection In Applications

    Connection in Applications Bosch recommends operating the AUTODOME 7100i IR camera models (NDP‑7602‑Z40L, NDP-7604-Z12L) by IEEE 802.3bt PoE Type 4, 90W. You can also use a third-party 24 VAC, 50/60Hz power supply that meets the stated requirements.

  • Page 11: Use Latest Software

    For full feature support of the AUTODOME 7100i camera, an IEEE 802.3bt Type 3 60W midspan from Bosch should be used for non IR models and the IEEE 802.3bt Type 4 90W midspan should be used for IR models.

  • Page 12: Important Notices - Illumination Safety

    | Safety AUTODOME 7100i│AUTODOME 7100i IR Important Notices - Illumination Safety The text in this section applies only to cameras that have illuminators. Notice! This product has been tested according to standard IEC 62471:2006 “Photobiological safety of lamps and lamp systems”. The product emissions exceed the EXEMPT Group limit for both Retinal Blue Light and Cornea/Lens infrared hazard as defined by IEC 62471:2006.

  • Page 13: Customer Support And Service

    AUTODOME 7100i│AUTODOME 7100i IR Safety | en Customer Support and Service If this unit needs service or if you need technical support, contact Bosch Security Systems Technical Support for instructions. USA and Canada Telephone: 800-289-0096, option 4 Fax: 800-315-0470 Email: technical.support@us.bosch.com Europe, Middle East, Africa, and Asia Pacific Regions Contact your local distributor or Bosch sales office.

  • Page 14: Unpacking

    AUTODOME 7100i │ AUTODOME 7100i IR camera Quick Installation Guide Safety instructions MAC address labels Tools Required The table that follows is a list of additional products, sold separately by Bosch or other manufacturers, necessary to install AUTODOME cameras. Quantity Product Size Part Number...
  • Page 15 AUTODOME 7100i│AUTODOME 7100i IR Unpacking | en Torque wrench with torque (user-supplied) range of 10-12 Nm (90-105 in.- The table that follows has a list of additional tools and accessories that may be necessary to complete installation. Tool / Accessory...
  • Page 16 | Unpacking AUTODOME 7100i│AUTODOME 7100i IR Tool / Accessory Purpose Available from Bosch? – SFP modules must meet the following temperature specifications that occur inside the AUTODOME 7100i mount: +85°C (+185°F) case temp. Copper power wire Make connections for 24VAC +/- 10%/36VDC.

  • Page 17: Product Description

    The design gives undistorted, high-resolution video above the horizon, which is helpful in city landscapes that are not flat. The camera has been designed for quick and easy installation, a key feature from Bosch IP video security products.

  • Page 18: Configuring The Camera Before Installation

    When you are configuring the camera in its packaging and you plan to install it on a pipe mount, you must use a complete Bosch pipe mount (NDA-7100-PIPE or NDA-7100-PIPEF) to supply power to the camera. It is the only way to make sure the board within the pipe mount is installed in the correct way.

  • Page 19: Preparing The Bubble

    Dry the bubble thoroughly with a dry nonabrasive cloth to prevent water spots. Never scrub the bubble with any abrasive material or cleaners. Bosch recommends cleaning the exterior of the bubble with NOVUS “No. 1” Plastic Clean & Shine (or equivalent), according to manufacturer’s instructions. Refer to www.novuspolish.com...

  • Page 20: Optional) Installing An Sd Card

    Handle the bubble with care. Do not scratch the inside of the bubble which doesn’t have a hard coating. Notice! Use full size SD cards for maximum reliability. Bosch doesn’t recommend the use of microSD cards or of microSD to SD adapters. Notice! Before adding or removing a full size SD card from the camera, disconnect all power sources (including PoE) from the device.
  • Page 21 AUTODOME 7100i│AUTODOME 7100i IR (Optional) Installing an SD card | en Replace the bubble. 10. Turn the bubble counterclockwise 10 degrees until it locks into position. Bosch Security Systems 2023-09-29 | V06 | F.01U.410.315 Installation Manual...
  • Page 22 See sections Recommendations for 24VAC Power Supply and Compatible 24VAC Power Supplies Note: Bosch Wall, mast (pole) and corner mounts are only guaranteed to work with Bosch power supplies. Before mounting the Power Supply Box, decide if you should wire the box through the holes in the bottom or back of the box.

  • Page 23: Installing A Mount Power Supply Box (Wall, Mast (Pole), And Corner Mounts)

    Mast Plate to the pole. Contact your Bosch Sales Representative to order Banding Tool P/N TC9311PM3T. Secure the Power Supply Box to the Corner Plate or Mast Plate using the four (4) 3/8 x1-3/4-inch bolts and split lock washers (supplied).

  • Page 24: Installing A Pendant Arm Mount

    | Installing a pendant arm mount AUTODOME 7100i│AUTODOME 7100i IR Installing a pendant arm mount Notice! Risk of water ingress If you: - remove a camera from its mount but do not replace it promptly, or - install the mount but do not install the camera immediately, then you must remove the PCB from the mount to avoid moisture or water ingress and potential corrosion.
  • Page 25 AUTODOME 7100i│AUTODOME 7100i IR Installing a pendant arm mount | en To the NDA-PEND-WPLATE mounting plate: Connect the back of the pendant arm to the NDA-PEND-WPLATE mounting plate, as in the figure that follows. Note: Use liquid-tight, electrically grounded conduit in order to maintain the IP66 rating, and so that the metal conduit is connected electrically to the NDA-PEND- WPLATE mounting plate.
  • Page 26 | Installing a pendant arm mount AUTODOME 7100i│AUTODOME 7100i IR Make the appropriate connections for PoE, 24VAC ± 10%/36VDC ± 10%, alarms, audio. For IR models: If you connect fiber to the camera, then connect only 24VAC ± 10% or 36VDC ±...
  • Page 27 AUTODOME 7100i│AUTODOME 7100i IR Installing a pendant arm mount | en To Connect the AUTODOME 7100i Non-IR NDP-7602-Z40 to the Wall arm and 24VAC PSU Kits (NDA-7100-PA0(F), NDA-7100-PA1(F) and NDA-7100-PA(F): Connect the PSU to the back of the pendant wall arm, as in the figure that follows.
  • Page 28 | Installing a pendant arm mount AUTODOME 7100i│AUTODOME 7100i IR Warning! Serious injury or death can occur if the hinge pins of the Pendant Arm are not fully engaged (locked) to the Power Supply Box. Exercise caution before releasing the Pendant Arm.
  • Page 29 AUTODOME 7100i│AUTODOME 7100i IR Installing a pendant arm mount | en Ground screw Ground wire to wall arm mount P101 Connector; Power In (120 VAC / P107 Connector; 24 VAC (pins 4, 5) and 230 VAC, 50/60 Hz) ground (pin 3) to camera through the...
  • Page 30 For IR models: If you connect fiber to the camera, connect PoE, but do not connect the Ethernet cable. Alternately power the camera with 36VC ± 10% power or 24VAC ± 10% from a non Bosch power supply. See Recommendations for 24 VAC Power Supply. 2023-09-29 | V06 | F.01U.410.315...
  • Page 31 AUTODOME 7100i│AUTODOME 7100i IR Installing a pendant arm mount | en For audio and/or alarm inputs/outputs (I/O): On the mount on the camera side, connect the drain wire of the Belden cable (or similar cable) to chassis ground and grounded metal box.
  • Page 32 | Installing a pendant arm mount AUTODOME 7100i│AUTODOME 7100i IR Notice! The following type of CAT 5E, CAT 6 or better Ethernet cable should be used: F/UTP overall screened cable with unscreened twisted pairs (often referred to as FTP),...
  • Page 33 AUTODOME 7100i│AUTODOME 7100i IR Installing a pendant arm mount | en Put the top cap onto the mount. Put the three (3) screws back into the top cap. 10. Tighten the screws. Notice! Risk of permanent damage to the camera The interface board connects only one way to the camera.
  • Page 34 | Installing a pendant arm mount AUTODOME 7100i│AUTODOME 7100i IR 13. Tighten the screws to 10-12 Nm. 14. Perform all the connections mentioned in the Connection section. 15. Apply power. 2023-09-29 | V06 | F.01U.410.315 Bosch Security Systems Installation Manual...
  • Page 35 AUTODOME 7100i│AUTODOME 7100i IR Installing a pendant arm mount | en 16. Remove the protective plastic sheet from the bubble. Installation is complete. Bosch Security Systems 2023-09-29 | V06 | F.01U.410.315 Installation Manual...

  • Page 36: Installing A Pipe Mount

    | Installing a pipe mount AUTODOME 7100i│AUTODOME 7100i IR Installing a pipe mount Notice! Risk of water ingress If you: - remove a camera from its mount but do not replace it promptly, or - install the mount but do not install the camera immediately, then you must remove the PCB from the mount to avoid moisture or water ingress and potential corrosion.
  • Page 37 AUTODOME 7100i│AUTODOME 7100i IR Installing a pipe mount | en To make a watertight seal, wrap PTFE tape (supplied with the pipe mount) four (4) times around the threads at the end of the mount. 1.5”NPT PIPE Put the appropriate cables for power, video, alarms, and audio through one of the access holes in the wall mounting plate.
  • Page 38 | Installing a pipe mount AUTODOME 7100i│AUTODOME 7100i IR Make the appropriate connections for PoE (only if not using fiber), 24VAC ± 10%/36VDC ± 10%, alarms, and audio. If you connect fiber to the camera, then connect only 24VAC/36VDC power input to the camera. Do not connect PoE.
  • Page 39 AUTODOME 7100i│AUTODOME 7100i IR Installing a pipe mount | en To install fiber, complete the four (4) steps that follow. For all other installations, skip to step 8. First, remove the screws from the bottom of the pipe mount. NDA-7100-PIPEF NDA-7100-PENF Install the SFP module into the fiber port in the mount.
  • Page 40 | Installing a pipe mount AUTODOME 7100i│AUTODOME 7100i IR Connect fiber optic cable to the SFP module. NDA-7100-PIPEF NDA-7100-PENF Notice! Hotplugging is not allowed for SFP fiber module. Power must be removed from the camera before plugging in an SFP module.

  • Page 41: Installing A Pipe Mount Onto A Nda-U-Rmt With Grounded Conduit

    AUTODOME 7100i│AUTODOME 7100i IR Installing a pipe mount | en Tilt the camera until you connect the camera to the mount. 10. Tighten the top cap screws. 11. Tighten the screws to 10-12 Nm. 12. Apply power. 13. Remove the protective plastic sheet from the bubble. Installation is complete.
  • Page 42 | Installing a pipe mount AUTODOME 7100i│AUTODOME 7100i IR Pull all the wires that need to connect to the AUTODOME camera through the NDA-U- RMT pipe and then through ¾-inch (19 mm) electrically conductive, liquid tight metal conduit. Note: To minimize the amount of unprotected cables, make sure the conduit is 50 to 100 mm (2 to 4 inches) from the open end of the pipe at the bottom of the NDA- U-RMT.

  • Page 43: Recommended Routing Of Ethernet Cable Through Pipe Mount

    AUTODOME 7100i│AUTODOME 7100i IR Installing a pipe mount | en Unscrew the bolt at the bottom of the NDA-U-RMT and add the 3/8” (9.5 mm) washer and the 3/8” (9.5 mm) ring terminal on the ground wire. Make sure there is a low resistance measurement between the metal of the bolt head and the grounded metal conduit so that the electrical ground is connected between the NDA-U-RMT and the grounded metal conduit.

  • Page 44: Connection

    7100i also known as PD side) using a single-signature PD. – AUTODOME 7100i IR: PoE midspan IEEE 802.3bt Type 4, Class 8, 4 Pair Power (4PPOE) 90W at PSE (POE midspan or POE Ethernet switch) side, (71.3W at AUTODOME 7100i also known as PD side) using a single-signature PD.
  • Page 45 PC, using an Ethernet crossover cable with RJ45 connectors. (See the bottom graphic in the first figure that follows.) – a midspan from Bosch that meets the IEEE 802.3bt, Type 3/4 (60W/90W) standard (See the second figure that follows.) Note: midspans from Bosch with IEEE 802.3at or IEEE 802.3af are not compatible.) Figure 10.1: System Configuration with AUTODOME camera...
  • Page 46 | Connection AUTODOME 7100i│AUTODOME 7100i IR Figure 10.2: System Configuration: AUTODOME 7100i camera to midspan 1 AUTODOME camera 2 Midspan DATA & PWR OUT 3 IEEE 802.3bt Type 3/4 (Class 6/8) midspan 4 Midspan DATA IN (to Ethernet switch or test PC) 2023-09-29 | V06 | F.01U.410.315...

  • Page 47: Power By Midspan

    10.2.1 Recommendations for third-party IEEE 802.3bt PoE Power Supply Bosch recommends the use of one of the IEEE 802.3bt Type 3, Class 6 midspans (Refer to the subchapter Connecting the AUTODOME camera to the PC in the Installation Manual) for use with the non-IR AUTODOME camera model and one of the IEEE 802.3bt Type 4, Class 8...

  • Page 48: Connecting Watertight, Electrically Grounded Metal Conduit To Bosch Outdoor Midspans

    | Connection AUTODOME 7100i│AUTODOME 7100i IR 10.2.2 Connecting watertight, electrically grounded metal conduit to Bosch Outdoor Midspans Unscrew and remove the fittings from the DATA & PWR OUT and DATA IN ports of the Bosch Outdoor midspan. Find electrically conductive liquid tight metal conduit with PG16 threads to screw into the two holes, or find an appropriate liquid tight fitting to adapt a PG16 male thread to the conduit of your choice such as ½...

  • Page 49: Power By 24 Vac/36 Vdc

    10.3.1 Recommendations for 24 VAC Power Supply Bosch recommends operating the AUTODOME 7100i IR camera models (NDP‑7602‑Z40L, NDP-7604-Z12L) by IEEE 802.3bt PoE Type 4, 90W. You can also use a third-party 24 VAC, 50/60Hz power supply that meets the stated requirements.

  • Page 50: Compatible 24 Vac Power Supplies

    For earlier AUTODOME arm mount installation, the VG4-A-PSU0, VG4-A-PSU1, VG4-A-PSU2 can be used, but will need to replace with new AUTODOME 7100i arm and wire properly. Please note that the paint will not match in both of the cases mentioned previously.

  • Page 51: Fuse Specifications And Power Wire Gauges

    AUTODOME 7100i│AUTODOME 7100i IR Connection | en 10.3.3 Fuse specifications and power wire gauges Warning! Fuse replacement by qualified service personnel only. Replace with same type fuse. Fuse Specifications Volts XF101 Mains XF102 XF103 24 VAC T 5.0 A T 2.0 A T 3.15 A...

  • Page 52: Connecting 24 Vac / 36 Vdc Power To The Camera

    | Connection AUTODOME 7100i│AUTODOME 7100i IR 10.3.4 Connecting 24 VAC / 36 VDC power to the camera Connect 24VAC +/- 10%, 50/60Hz or 36VDC +/- 10% to Connector X105 pins 1 and 2 as in the figure that follows.

  • Page 53: Making Connections In The Power Supply With Wall Arm (Nda-7100-Pa0(F), Nda-7100-Pa1(F)

    Because the IR models of the AUTODOME 7100i (NDP-7602-Z40L, NDP-7602-Z12L) are rated to 24VAC @ 3.5A, which will exceed the current output of the 3.15A fuse (labeled XF103 in the power supply), you cannot use the IR models of the AUTODOME 7100i camera with the following power supplies:...
  • Page 54 | Connection AUTODOME 7100i│AUTODOME 7100i IR Figure 10.4: Connections with the power supply with wall arm Ground screw Ground wire to wall arm mount P101 Connector; Power In (120 VAC / P107 Connector; 24 VAC (pins 4, 5) and 230 VAC, 50/60 Hz)
  • Page 55 Neutral power to (3.15A the camera FUSE) 24VAC to AUTODOME 7100i NDP-7602-Z40 camera P105 Serial Communi- cations Not used for AUTODOME 7100i P106 Serial Communi- cations J103 Older Fiber Connection Bosch Security Systems 2023-09-29 | V06 | F.01U.410.315 Installation Manual...
  • Page 56 | Connection AUTODOME 7100i│AUTODOME 7100i IR To wire the incoming high-voltage and the outgoing low-voltage lines properly, refer to this table: Connector Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Ground Grounding Screw - External Earth ground connection...
  • Page 57 X105 in the camera, but not so long as to be pinched by or to obstruct closing the cover door. c. Attach the 24VAC lines to AUTODOME 7100i User Interface connector X105, as illustrated below. 10. Route the Ethernet cable through the points mentioned in the list that follows, in sequence: a.
  • Page 58 | Connection AUTODOME 7100i│AUTODOME 7100i IR X104 X105 X106 To connect audio I/O and/or alarm inputs or alarm relay output from the AUTODOME 7100i User Interface connections through the arm to the PSU box: Route the audio inputs, audio outputs, and/or alarm inputs and alarm relay output from connector X106 (see figure above) in the User Interface board in the arm mount through the arm to the power supply box.

  • Page 59: Attaching The Pendant Arm To The Power Supply Box

    AUTODOME 7100i│AUTODOME 7100i IR Connection | en 10.3.6 Attaching the pendant arm to the power supply box Note: Refer to the figure that follows as you complete the steps to attach the pendant arm to the power supply box. Notice! You must compress both hinge pins fully to open (unlock) the hinges of the pendant arm.

  • Page 60: Making Connections In The 24Vac Power Supply With Lid (Nda-U-Psu0, Nda-U-Psu1, Nda-U-Psu2)

    Because the IR models of the AUTODOME 7100i (NDP-7602-Z40L, NDP-7602-Z12L) are rated to 24VAC @ 3.5A, which will exceed the current output of the 3.15A fuse (labeled XF103 in the power supply), you cannot use the IR models of the AUTODOME 7100i camera with the following power supplies:...
  • Page 61 AUTODOME 7100i│AUTODOME 7100i IR Connection | en Figure 10.5: 24VAC power supply with (1) the high-voltage section (120VAC, 230VAC), (2) the low- voltage section (24VAC), and (3) the metal barrier that separates the two sections The graphic that follows shows the connections for the power supply with wall arm (120 VAC, 230VAC models).
  • Page 62 Warning! If reusing a VG4-A-PSU0, VG4-A-PSU1 and VG4-A-PSU2 from an earlier Bosch AUTODOME camera, the cable wiring will need to be redone as shown and should not be plugged into connectors P106 and P105 of the Power Supply Unit.
  • Page 63 FUSE) 24VAC to AUTODOME 7100i NDP-7602-Z40 camera P105 Serial Communicat ions Not used for AUTODOME 7100i P106 Serial Communicat ions J103 Older Fiber Connection Warning! All wiring (power and I/O cabling) connecting to the unit must be routed separately inside permanently earthed metal conduits (not supplied).
  • Page 64 Connect three wires to the P107 Power Out connector to route the 24 VAC power supply to the AUTODOME 7100i non-IR model (NDP-7602-Z40). Refer to connector P107 in the table above and to the image below for an illustration of these connections.
  • Page 65 X105 in the camera, but not so long as to be pinched by or to obstruct closing the cover door. c. Attach the 24VAC lines to AUTODOME 7100i User Interface connector X105, as illustrated below. Note: Use of proper grommets is necessary to guarantee an IP66 rating.
  • Page 66 12. (Optional step) Connect audio I/O and, or alarm inputs or alarm relay output from the AUTODOME 7100i User Interface connections in one conduit hole and out the other, through one of the two conduit holes in the PSU box, into a ¾” (20mm) or a ½”...

  • Page 67: Optional) Support For Fiber Optic Cable Installation

    PENF and NDA-7100-PIPEF mounts must be removed before installing or removing an SFP module. Warning! The AUTODOME camera does not support 100Mbps SFP fiber modules by Bosch. Warning! If an SFP module is added to the NDA-7100-PENF or NDA-7100-PIPEF mount and connected to an AUTODOME camera, the Ethernet port in the camera will automatically be disabled, even if no fiber is connected to the SFP module.
  • Page 68 | Connection AUTODOME 7100i│AUTODOME 7100i IR Typical connection configuration 2023-09-29 | V06 | F.01U.410.315 Bosch Security Systems Installation Manual...

  • Page 69: Connecting The Alarm Inputs And Alarm Relay Output

    AUTODOME 7100i│AUTODOME 7100i IR Connection | en 10.5 Connecting the Alarm Inputs and Alarm Relay Output The Alarm Inputs and Alarm Output lines should use twisted pair wires with a foil shield where the drain wire of the foil shield is connected to the chassis/housing ground in the mount (NDA-7100-PIPE, NDA-7100-PIPEF, NDA-7100-PEN, NDA-7100-PENF) as described below.

  • Page 70: Connecting The Audio Input And Output Wires

    | Connection AUTODOME 7100i│AUTODOME 7100i IR Wire size Alarm inputs - Alarm output - Maximum distance Maximum distance Meters Feet Meters Feet 0.643 152.4 N/A at N/A at maximum maximum current current 0.811 243.8 These numbers assume maximum relay load. If switching less than this, re-calculate with the exact switching load for your particular use case to increase the allowed distances.

  • Page 71: Troubleshooting

    The camera has the wrong power supply. Solutions – Test the camera with another power supply. – Check the Bosch website for a software update that might address the issue. Bosch Security Systems 2023-09-29 | V06 | F.01U.410.315 Installation Manual...

  • Page 72: Dark Picture

    | Troubleshooting AUTODOME 7100i│AUTODOME 7100i IR 11.5 Dark picture Possible root causes – The camera iris is closed. – The camera bubble still has its protective plastic sheet. – The Ethernet cable exceeds the maximum length (100 m (328 ft)). –...

  • Page 73: No Camera Control

    Trying pressing the Factory Default button. If Fiber optic output is used with NDA-7100-PIPEF or NDA-7100-PENF: – Check that a Bosch 100Mbps SFP module is not being used since it is not supported. – Check that the SFP module supports 1 Gbps.

  • Page 74: No Video

    | Troubleshooting AUTODOME 7100i│AUTODOME 7100i IR – Check that the fiber optic cable is plugged into the SFP module on both sides of the network. – Check that the fiber optic cable is not damaged and is terminated properly.

  • Page 75: Weak Contrast On Screen

    – The camera web browser needs a refresh. – The iris is closed. – There is a problem with the version of the Bosch VideoSDK software. – The scene does not have adequate light. Solutions – Refresh the web browser.

  • Page 76: Rebooting The Unit

    | Troubleshooting AUTODOME 7100i│AUTODOME 7100i IR Notice! A factory default deletes all camera settings including passwords, network settings, and image settings. Complete the following sequence of steps only if you have no other option to restore operation to the camera.
  • Page 77 If you cannot control the unit after the firmware upgrade, then cycle the power to the unit. If a power reset does not solve the problem, or if Configuration or video management software identifies the unit as “Videojet Generic,” then contact your Bosch Service Center for an RMA for the unit.

  • Page 78: Maintenance

    Dry the bubble thoroughly with a dry nonabrasive cloth to prevent water spots. Never scrub the bubble with any abrasive material or cleaners. Bosch recommends cleaning the exterior of the bubble with NOVUS “No. 1” Plastic Clean & Shine (or equivalent), according to manufacturer’s instructions. Refer to www.novuspolish.com...

  • Page 79: Technical Data

    AUTODOME 7100i│AUTODOME 7100i IR Technical data | en Technical data For product specifications, see the datasheet for your camera, available on the appropriate product pages of the Online Product Catalog at www.boschsecurity.com. Bosch Security Systems 2023-09-29 | V06 | F.01U.410.315...

  • Page 80: Support Services And Bosch Academy

    Support services and Bosch Academy Support Access our support services at www.boschsecurity.com/xc/en/support/. Bosch Building Technologies Academy Visit the Bosch Building Technologies Academy website and have access to training courses, video tutorials and documents: www.boschsecurity.com/xc/en/support/training/ 2023-09-29 | V06 | F.01U.410.315 Bosch Security Systems...
  • Page 81 AUTODOME 7100i│AUTODOME 7100i IR Support services and Bosch Academy | Bosch Security Systems 2023-09-29 | V06 | F.01U.410.315 Installation Manual...
  • Page 82 | Support services and Bosch Academy AUTODOME 7100i│AUTODOME 7100i IR 2023-09-29 | V06 | F.01U.410.315 Bosch Security Systems Installation Manual...
  • Page 84 Building solutions for a better life. 202309292136...

This manual is also suitable for:

Autodome 7100i irNdp-7602-z40Ndp-7602-z40lNdp-7604-z12lNdp-7602-z40-caNdp-7602-z40l-ca ... Show all

Table of Contents