Grizzly T33295 Owner's Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Wire Feeders
  5. T33295
  6. Owner's manual
Grizzly T33295 Owner's Manual

Grizzly T33295 Owner's Manual

2/3 hp variable-speed 7-roller power feeder
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL T33295
2/3 HP VARIABLE-SPEED
7-ROLLER POWER FEEDER
OWNER'S MANUAL
(For models manufactured since 03/23)
COPYRIGHT © APRIL, 2023 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JM22639 PRINTED IN TAIWAN
V1.04.23
***Keep for Future Reference***

Advertisement

Table of Contents
loading

Related Manuals for Grizzly T33295

Summary of Contents for Grizzly T33295

  • Page 1 (For models manufactured since 03/23) COPYRIGHT © APRIL, 2023 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #JM22639 PRINTED IN TAIWAN V1.04.23...
  • Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.

  • Page 3: Table Of Contents

    Table of Contents INTRODUCTION ..........................2 Contact Info ..........................2 Manual Accuracy ........................2 Identification ..........................3 Controls & Components ......................4 SECTION 1: SAFETY ........................8 Safety Instructions for Machinery ....................8 Additional Safety for Power Feeders ..................10 SECTION 2: POWER SUPPLY ......................

  • Page 4: Introduction

    ID label (see below). This information is required for us to provide proper tech support, and it helps us determine if updated documentation is available for your machine. Manufacture Date Serial Number Model T33295 (Mfd. Since 03/23)

  • Page 5: Identification

    O. Motor G. Control Panel P. Chain Cover H. Upper Elbow Joint Q. Lower Elbow-Joint Vertical Travel Crank Handle R. Base To reduce your risk of serious injury, read this entire manual BEFORE using machine. Model T33295 (Mfd. Since 03/23)

  • Page 6: Controls & Components

    7–86 FPM. To start motor, press dial until it beeps and control panel glows red. To stop motor, press dial again. To adjust feed rate, press SET button, then rotate dial clockwise to increase feed rate or counterclockwise to decrease feed rate. Model T33295 (Mfd. Since 03/23)
  • Page 7 Tighten to secure power feeder swivel position. P. Swivel Lock Pin: Allows power feeder to rotate when disengaged. Locks power feeder in horizontal position when engaged in either of two detents. Model T33295 (Mfd. Since 03/23)
  • Page 8 MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL T33295 2/3 HP VARIABLE‐SPEED 7‐ROLLER POWER FEEDER Product Dimensions: Weight................................119 lbs. Width (side-to-side) x Depth (front-to-back) x Height............37-1/2 x 20-1/2 x 29-1/2 in.
  • Page 9 The information contained herein is deemed accurate as of 4/27/2023 and represents our most recent product specifications. Model T33295 PAGE 2 OF 2 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. Model T33295 (Mfd. Since 03/23)

  • Page 10: Section 1: Safety

    Never operate under the influence of drugs or injury or blindness from flying particles. Everyday alcohol, when tired, or when distracted. eyeglasses are NOT approved safety glasses. Model T33295 (Mfd. Since 03/23)
  • Page 11 Make sure they are properly installed, you experience difficulties performing the intend- undamaged, and working correctly BEFORE ed operation, stop using the machine! Contact our operating machine. Technical Support at (570) 546-9663. Model T33295 (Mfd. Since 03/23)

  • Page 12: Additional Safety For Power Feeders

    If normal safety pre- respect. Failure to do so could result in cautions are overlooked or ignored, seri- serious personal injury, damage to equip- ous personal injury may occur. ment, or poor work results. -10- Model T33295 (Mfd. Since 03/23)

  • Page 13: Section 2: Power Supply

    To reduce the risk of these hazards, avoid over- loading the machine during operation and make sure it is connected to a power supply circuit that meets the specified circuit requirements. -11- Model T33295 (Mfd. Since 03/23)
  • Page 14 Minimum Gauge Size ......18 AWG all local codes and ordinances. Maximum Length (Shorter is Better)..50 ft. -12- Model T33295 (Mfd. Since 03/23)

  • Page 15: Section 3: Setup

    E. Angle Adjustment Scale ......1 you are completely satisfied with the machine and Rotation Knob M10-1.5 ....... 1 have resolved any issues between Grizzly or the shipping agent. You MUST have the original pack- aging to file a freight claim. It is also extremely helpful if you need to return your machine later.

  • Page 16: Hardware Recognition Chart

    Hardware Recognition Chart USE THIS CHART TO MATCH UP HARDWARE DURING THE INVENTORY AND ASSEMBLY PROCESS. Flat Head Screw -14- Model T33295 (Mfd. Since 03/23)

  • Page 17: Cleanup

    NOTICE unsupervised use. Avoid harsh solvents like acetone or brake parts cleaner that may damage painted sur- faces. Always test on a small, inconspicu- ous location first. -15- Model T33295 (Mfd. Since 03/23)

  • Page 18: Assembly

    Tighten set screw and hex nut just enough to secure handwheel. Note: Do not overtighten set screw or hand- Figure 11. Rotation knob installed. wheel will not rotate. -16- Model T33295 (Mfd. Since 03/23)
  • Page 19 Indicator Upper Line Elbow-Joint Sticker Lower Elbow-Joint "0" Angle Adjustment Scale Rotation Lock Figure 15. Angle adjustment scale and indicator Figure 13. Upper and lower elbow-joints aligned. line sticker installed. -17- Model T33295 (Mfd. Since 03/23)

  • Page 20: Base Mounting

    " lower than the thickness of the workpiece. Shaper Jointer Table Saw Blade Optional Cutter Featherboard 7-Roller Fence Feed Fence Models Feed Feed Fence Cutterhead Figure 16. Typical power feed mounting on a shaper, jointer, and table saw. -18- Model T33295 (Mfd. Since 03/23)

  • Page 21: Checking Gearbox Oil Level

    Apply Medium Grade halfway, then replace oil plug. Table Support Thread-Locking Compound Webbing Install chain cover and rotate power feeder Figure 18. Direct mounting. back into position for operation. -19- Model T33295 (Mfd. Since 03/23)

  • Page 22: Test Run

    Rollers should rotate Speed Feed in clockwise direction (when viewed from top). Adjustment Direction Dial Button Button Press variable-speed adjustment dial to stop rollers. Figure 20. Readout illuminated. Test Run is complete. -20- Model T33295 (Mfd. Since 03/23)

  • Page 23: Section 4: Operations

    11. Stops power feeder, then stops machine. formal training before beginning any proj- ects. Regardless of the content in this sec- tion, Grizzly Industrial will not be held liable for accidents caused by lack of training. -21- Model T33295 (Mfd. Since 03/23)

  • Page 24: Basic Use & Care

    Use a featherboard on the infeed side to assist with feeding long or large stock. 1° to 1.5° Angle Optional Featherboard Feed Figure 21. Example of power feeder toe-in on table saw. -22- Model T33295 (Mfd. Since 03/23)

  • Page 25: Changing Speeds

    Changing Speeds Adjusting Roller Angle The Model T33295 can be positioned to feed To reduce risk of shock or workpieces so the rollers are angled relative to accidental startup, always the machine fence from 45°–90°. For example, it disconnect machine from can be positioned at 90°...
  • Page 26 Figures 26–27. (Side View) Power Workpiece Feeder Fence Power Feeder Roller Table Figure 26. Example of power feeder set up for 90° feeding operation on shaper against a fence. -24- Model T33295 (Mfd. Since 03/23)

  • Page 27: Section 5: Accessories

    " wide x 2 ⁄ " diameter rollers are roller table on one or both sides of your saw and made from synthetic rubber and fit the T33295. production time is automatically improved! Figure 30. T33851 Replacement Roller. Figure 28. Heavy-duty roller tables.
  • Page 28 T32404—EDGE Mazeno Safety Glasses, Clear filler pump. T32323 T32401 T32402 T32404 Figure 34. H8255 Grease Gun. Figure 32. Assortment of basic eye protection. www.grizzly.com 1-800-523-4777 order online at or call -26- Model T33295 (Mfd. Since 03/23)

  • Page 29: Section 6: Maintenance

    To reduce risk of shock or accidental startup, always disconnect machine from power before adjustments, Cleaning the Model T33295 is relatively easy. maintenance, or service. Frequently blow off sawdust with compressed air. This is especially important for internal working parts and the motor. Dust build-up around the Schedule motor will decrease its lifespan.
  • Page 30 Install chain cover and rotate power feeder back into position for operation. Figure 36. Location of chain grease fittings (chain cover removed). -28- Model T33295 (Mfd. Since 03/23)
  • Page 31 (see Figure 39), then eral times to distribute the grease. rotate leadscrew through its full path to distribute the grease. Vertical Travel Leadscrew Overarm Rack Figure 41. Overarm rack teeth. Figure 39. Vertical travel leadscrew. -29- Model T33295 (Mfd. Since 03/23)

  • Page 32: Section 7: Service

    5. Replace roller(s) (Page 31). 6. Rollers loose. 6. Tighten rollers (Page 31). Workpiece cut 1. Feed speed too slow. 1. Increase feed speed. is burnt. 2. Dull cutter or blade. 2. Install sharp cutter or blade. -30- Model T33295 (Mfd. Since 03/23)

  • Page 33: Replacing Rollers

    Socket " ............1 ⁄ Socket Wrench ..........1 Remove and replace roller. Replacement Rollers (Model T33851). . As Needed Install hex nut and washer and tighten. To replace roller: DISCONNECT MACHINE FROM POWER! -31- Model T33295 (Mfd. Since 03/23)

  • Page 34: Section 8: Wiring

    Technical Support at (570) 546-9663. The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com. -32- Model T33295 (Mfd. Since 03/23)

  • Page 35: Wiring Diagram

    8A 250V 8A 250V RS485 Circuit Board SUT-19522 JACKCON JACKCON 1000µF 1000µF Ground 200V 200V 6-15 Plug Figure 43. Motor circuit board wiring. Figure 44. Digital readout circuit board. READ ELECTRICAL SAFETY -33- Model T33295 (Mfd. Since 03/23) ON PAGE 32!

  • Page 36: Section 9: Parts

    SECTION 9: PARTS We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability. Main 50-1 50-2 50-3 50-4...
  • Page 37 POWER CORD 3W 18G 72" 6-15P PT33295050 PT33295091 MOTOR CIRCUIT BOARD 50-1 PT33295050-1 SPEED ADJUSTMENT DIAL PT33295092 PHLP HD SCR M4-.7 X 8 BUY PARTS ONLINE AT GRIZZLY.COM! -35- Model T33295 (Mfd. Since 03/23) Scan QR code to visit our Parts Store.

  • Page 38: Column & Stand

    Column & Stand BUY PARTS ONLINE AT GRIZZLY.COM! -36- Model T33295 (Mfd. Since 03/23) Scan QR code to visit our Parts Store.
  • Page 39 T-HANDLE, 150MM W/HOLE FOR PIN PT33295125 FLAT WASHER 17 X 30 X 0.5MM PT33295151 ROLL PIN 6 X 22 PT33295126 ELEVATION HANDLE ARM 130L BUY PARTS ONLINE AT GRIZZLY.COM! -37- Model T33295 (Mfd. Since 03/23) Scan QR code to visit our Parts Store.

  • Page 40: Labels & Cosmetics

    Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. BUY PARTS ONLINE AT GRIZZLY.COM! -38- Model T33295 (Mfd.

  • Page 43: Warranty & Returns

    WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.

Table of Contents