Advertisement
7. Position the wiring in the exit slot and reinstall the
5800RL's cover on the base.
Test the 5800RL module with the rest of the system.
DIP SWITCH POSITIONS
HOUSE
ID
2
3
4
5
-
-
-
0
-
1
-
-
-
-
2
-
-
-
ON
3
-
-
-
ON
4
-
-
ON
-
5
-
-
ON
-
6
-
-
ON
ON
7
-
-
ON
ON
8
-
ON
-
-
9
-
ON
-
-
10
-
ON
-
ON
11
-
ON
-
ON
12
-
ON
ON
-
13
-
ON
ON
-
14
-
ON
ON
ON
15
-
ON
ON
ON
" – " indicates "OFF"
1
SW-1
NOT USED
Figure 4. DIP Switch Settings
RELAY and LED Operation
The 5800RL contains two relays (Figure 2) (SPDT, rated 2A.
28VAC/VDC) that may be used to activate remote sounders
and/or remote arm/disarm indicators. There are three LEDs
(green, yellow, red) located above the DIP switch and one
LED (red) located approximately in the center of the pc board.
The LEDs located above the DIP switch, indicate power and
relay activity. Refer to Figure 5. The RF Interference LED
monitors local radio frequency interference. If this LED is
continuously lit, the 5800RL should be relocated.
Relay
LED
Activates Upon...
A
Yellow
Alarm conditions as follows:
Steady ON = burglary alarm (NO contact
connects to COM)
Temporal ON = fire alarm (NO contact connects
temporal to COM)
OFF = no alarms present (NC contact connects
to COM)
ÊK37906Š
K3790 6/07 Rev. B
DIP SWITCH POSITIONS
HOUSE
ID
6
2
3
4
-
-
-
-
16
17
ON
ON
-
-
18
-
ON
-
-
19
ON
ON
-
-
20
-
ON
-
ON
21
ON
ON
-
ON
22
-
ON
-
ON
23
ON
ON
-
ON
24
-
ON
ON
-
25
ON
ON
ON
-
26
-
ON
ON
-
27
ON
ON
ON
-
28
-
ON
ON
ON
ON
29
ON
ON
ON
30
-
ON
ON
ON
31
ON
ON
ON
ON
SV6
7L
2
3
4
5
6
OFF POSITION
INDICATOR
2-6 SETS HOUSE ID
5800RL DIP Switch
5800RF-003-V0
2 Corporate Center Drive, Melville, NY 11747
Copyright © 2007 Honeywell International Inc.
Relay
LED
B
Red
5
6
N/A
Green
-
-
-
ON
N/A
RF
ON
-
Inter-
ON
ON
ference
-
-
Figure 5. Relay and LED Operation
-
ON
ON
-
SPECIFICATIONS
ON
ON
Dimensions: 2-3/4"W x 4-15/16"H x 1-1/16"D
-
-
(70mm x 125mm x 27mm)
-
ON
Voltage:
12VDC 100mA or
ON
-
9VAC, 15VA (use ADEMCO 1332 or equivalent)
ON
ON
Current:
-
-
Relay:
-
ON
ON
-
Operating Temperature: 0 - 50 ° C / 32 - 122 ° F
ON
ON
Federal Communications Commission (FCC) Part 15
The user shall not make any changes or modifications to the equipment
unless authorized by the Installation Instructions or User's Manual.
Unauthorized changes or modifications could void the user's authority to
operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
FCC/IC STATEMENT
This device complies with Part 15 of the FCC rules and RSS 210 of
Industry Canada. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause
undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS
210 des Industries Canada. Son fonctionnement est soumis aux
conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences
nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris
les interferences causant une reception indésirable.
www.honeywell.com/security
Activates Upon...
System armed/disarmed as follows:
ON = system armed Away, Stay, or Instant (NO
contact connect to COM)
OFF = system disarmed (NC contact connects to
COM)
Normally on (lighted) when power is applied.
Flickering indicates RF is being processed.
Lights when RF activity is present.
60mA
Two relays, each with choice of normally open (NO)
or normally closed (NC) operation.
Advertisement
