Page 1
ECHNICAL INFORMATION PRODUCT P 1/11 Models No. BJR182 Description Cordless Recipro Saw ONCEPT AND MAIN APPLICATIONS Model BJR182 has been developed as a sister tool of BJR181. featuring higher cost-competitiveness than the current model. Dimensions: mm (") Length (L) 449 (17-3/4) Width (W) 91 (3-5/8) Height (H)
Page 2
Assembling Pin 3 to the Blade clamp section [2] LUBRICATION and ADHESIVE Lubrication: Apply Makita grease FA No.2 to the following portions designated with the black triangle to protect parts and product from unusual abrasion. (Fig. 1) Adhesive: When reusing threadlocker coated screws, be sure to apply adhesive before tightening.
Page 3
P 3/11 epair [3] DISASSEMBLY/ASSEMBLY [3] -1. Blade Clamp Section Fig. 2 DISASSEMBLING Blade clamp section 1) Remove Shoe. If the Blade clamp section is positioned inside Gear housing, pull it out of Gear housing. (Fig. 2) 2) After removing Protector, remove Retaining ring S-18 using 1R291. Then remove the following parts: Driving sleeve, Shoulder pin 5, Compression spring 6, Pin 3 (of 6mm length), Guide sleeve, Driving sleeve guide...
Page 4
P 4/11 epair [3] -1. Blade Clamp Section (cont.) ASSEMBLING 1) Assemble Torsion spring 17 to Slider as illustrated in Fig. 7. Important: Be sure that Torsion spring 17 is not reversible when assemble to Slider. Follow the instruction described in Fig. 7. 2) Insert Compression spring 2 into the slit of Slider.
Page 5
P 5/11 epair [3] -1. Blade Clamp Section (cont.) 5) While fitting the two projections of Driving sleeve in the concavities of Sleeve, push Driving sleeve into Gear housing. At this time, turn Driving sleeve clockwise so that the protruding portion of Driving sleeve cannot be interfered by Gear housing.
Page 6
P 6/11 epair [3] -3. Slider Section DISASSEMBLING 1) After removing Shoe, then Insulation cover. (Fig. 13) 2) Remove the Blade clamp section. (See "[3] -1. Blade Clamp Section.) Fig. 13 For smooth removal of Insulation cover, apply soapy water into the space between Insulation cover Insulation cover and Gear housing cover complete.
Page 7
ASSEMBLING Do the reverse of the disassembling steps. Note: a) Do not forget to apply Makita grease FA No.2 to slider before assembling. (Fig. 17) b) Both of the two Plane bearing 14A's are not reversible when assembled to Slider.
Page 8
Do the reverse of the disassembling steps. Note: a) Apply Makita grease FA No.2 to the following parts, before assembling: *Flat washer 14: the surface that contacts Gear assembly *Pin 10 (of Gear housing complete): surface that contacts Gear assembly b) Torx socket head screw M5x14 is threadlocker coated.
Page 9
P 9/11 epair [3] -6. Armature DISASSEMBLING 1) Separate Gear housing cover complete from Gear housing complete. (Figs. 13, 14) 2) Remove Carbon brushes, then separate the assembly of Armature and Gear housing complete from Motor housing complete by unscrewing four 5x25 tapping screws. (Fig. 23) Fig.
Page 10
P 10/11 ircuit diagram Fig. D-1 Color index of lead wires' sheath Black Right side Brush holder, Right Left side Switch Brush holder, Left Right side Brush holder, Right Switch Heatsink Brush holder, Left Left side Terminal...
Page 11
P 11/11 iring diagram 1) Rear of Motor Housing Fig. D-2 Fix Lead wire of each Brush holder with Lead wire holders as illustrated below. Lead wire Motor housing Lead wire holder Lead wire holder on Motor housing on Motor housing Lead wire holder Lead wire holder on Brush holder...