Reading Settings Data - Kenwood TS-890S Instruction Manual

Reading Settings Data

Follow the steps below to read the settings data file of the
transceiver that is stored in the built-in memory or a USB flash
drive.
• To read data from a USB flash drive, insert the USB flash drive
containing the settings data into
1 Press [MENU].
2 Press F [USB/FILE] to display the USB/File
Management menu screen.
• If F [USB/FILE] is not displayed, press F [MORE] to display
F [USB/FILE].
3 Press F2 [
]/ F3 [
Configuration Data".
4 Press F4 [SELECT].
A screen for selecting the file (DATA) to read appears.
.
• Information of the location to read files from (built-in memory
or USB flash drive) that was last selected on this screen is
displayed. However, if a USB flash drive is not connected or
cannot be correctly recognized, information of the built-in
memory will be displayed.
• If no file is found, "No file is found." is displayed on the
screen.
5 Select the file to read.
• To read data from the internal memory, press F7 [INT.MEM].
• To read data from the USB flash drive, press F7
[USB.MEM]. (If a USB flash drive is not connected, a message
will appear prompting you to get ready the USB flash drive.)
• Pressing F5 [NAME] allows the file name to be changed.
• Pressing F6 [DELETE] displays a message to confirm
deletion of the file. Pressing F4 [OK] deletes the file.
6 Press F2 [ ]/F3 [
control to select the settings data file to read.
7 Press F4 [OK] to display the selection screen
(DATA) for reading the data.
• Pressing F7 [CANCEL] ends the operation without reading
a file.
.
8 Press F2 [
] or F3 [
control to select a function group to read.
(USB-A).
] to select "Read
] or turn the [MULTI/CH]
], or turn the [MULTI/CH]
USB/FILE MANAGEMENT 11
9 Press F5 [
] to select the checkbox to the left
of the settings data name.
• Pressing F5 [
(Settings data will not be read.)
10 Repeat steps 8 and 9 to select the corresponding
checkboxes for the settings data to read.
11 Press F4 [OK] to start reading the files.
Reading of settings data files with a check mark starts. When
reading starts, a reading in progress screen is displayed.
• Pressing F7 [CANCEL] exits the file selection screen
without starting reading and returns the display to the USB/
File Management menu screen.
• After the settings data files have been read successfully, a
message indicating that reading is complete is displayed.
12 Press F4 [OK] to end the process.
This transceiver reboots automatically.
Data that are not created by this transceiver cannot be
●
read.
The following function groups can be excluded from the
●
reading process.
• "Environmental Dependent" data (settings data that
are dependent on the installation environment)
• Antenna selection data and preset data of antenna
tuner
• Settings for items in menu group 6 (settings related
to the rear terminals)
• Advanced menu settings
• Linear amplifier menu settings
• Transverter settings
• LAN menu settings
• KNS menu settings and KNS registered users' list
• Clock menu settings
• "CW/RTTY/PSK Message Memory" data (CW/RTTY/
PSK message memory)
• "Voice Message Memory" data (voice message data)
If the settings data file is saved in a transceiver with a
●
newer firmware version, pressing F4 [OK] in step 7 will
result in an error. A "data reading error screen due to
mismatch between new and old firmware versions" is
displayed and reading is not executed.
If the settings data file is corrupted, pressing F4 [OK] in
●
step 7 will result in an error. A "file reading NG screen" is
displayed and reading is not executed.
If data mismatch is detected after reading a settings data
●
file, a "corrupted data is detected screen" is displayed.
When this occurs, pressing F4 [OK] runs a full reset and
reboots this transceiver.
] again deselects the checkbox.
11-3