Honeywell 8733500 - Digital Touchscreen Deadbolt Instructions

Installation Overview

Package Includes

1 - Exterior Faceplate
1 - Interior Faceplate
1 - User Guide
2 - Keys
1 - Strike Plate
1 - Mounting Plate
1 - Latch
1 - 1 3/8" Screw
2 - 5/16" Screws
2 - 1" Screws
4 - 3/4" Screws
2 - Mounting Posts
1 - Optional Set Screw

Please carefully check the above list to confirm all items have been received. If any items are missing, please contact Consumer Assistance. (See back for contact information)

Install Enclosed Latch and Strike Plate

Do not over-tighten latch screws.
NOTE: Do not extend Cylindrical Cover past 2-3/4" (70mm).

TO CONVERT FROM 2-3/8" (60mm) BACKSET TO 2-3/4" (70mm) BACKSET:

1. Hold latch with numbers facing forward and thumb pressing on the bolt.
2. Rotate the cylinder cover clockwise.
3. Pull and twist the extension plate all the way out.
4. Rotate the cylinder counter clockwise so that the marking aligns with the 2-3/4" position indicator.

The latch plate on the door needs to be straight and not protruding from door. Make adjustment before installing or this will cause problems with bolt fitting into latch hole.

Deadbolt Latch Must Be Retracted During Installation.

Remove (J) Screw from inside the battery compartment within the (B) Housing to release the Mounting Plate (C).

Screw Mounting Post (M) into holes on Mounting Plate (C).

Install Exterior Assembly

Check that the Rubber Gasket is secured on the Exterior Assembly. Insert the Exterior Assembly onto the door with the tailpiece going through the Deadbolt Latch Set in the VERTICAL POSITION.

Route the Control Wire through the door UNDER the Deadbolt Latch Set. Make sure the door is shut, lock and unlock using the key, ensure that the latch is operating smoothly and is aligned properly without scraping the strike plate.
If not, go back to step 2 and ensure you followed the steps.

Work with the door open
(K) screw goes into the door to prevent the lock from shifting and is optional.

Do not overtighten screws

Secure mounting plate to door

Install Interior Assembly

Carefully insert control wire into the wire connector

Work with the door open

NOTE: Make sure the connector dots line up with the dots on the control wire

Install Interior Assembly

NOTE: Make sure the Turn Knob is in the vertical position.
Be careful not to pinch the control wire when assembling.

Test the lock

Lock and unlock using the turn knob make sure the latch is opening and closing easily. If not, go back to step 2 and ensure you followed the steps.

Install Batteries and Cover

This Electronic lock requires (4) High Quality AA Alkaline batteries. When all 4 batteries are installed in the correct position, you should hear 2 beeps and the touchscreen will illuminate.

The Lock motor will engage and do a series of locking and unlocking motions in order to automatically determine your door "Handing" (left or right handed door).
When completed the lock will beep and the touchscreen will flash.

NOTE: Do not touch the touchscreen or turn knob until the light turns off.
Do not use rechargeable batteries or non-alkaline batteries.

Testing Operation

Test the lock button with door open

Test unlocking
Press 1-2-3-4-unlock

Before Opening Door
Let Motor Complete Cycle
NOTE: Let lock operation complete before attempting another action

Preparing Door

Tools Needed for Door Preparation (if there is no knob hole):
NOTE: Skip this step if your door comes with pre-drilled holes.

• Drill
• 2 1/8" Hole Saw
• 1" Hole Saw
• 3/4" Chiesel
  

Refer to Template included for Door Prep Instructions

Strike Plate Installation

NOTE: The strike plate on the door frame needs to be straight and not protruding from door frame. Make adjustment before installing or this will cause problems with bolt fitting into latch hole.

Programming Instructions

Read this manual carefully before Programming and operating!

Complete all the programming steps in the programming mode within 5 seconds
Do not press touchscreen until it stops illuminating, after you put in batteries

Creating Administrator Code

Touch screen to wake up lock.
Do not share admin code.

Adding a User Code

Touch screen to wake up lock.

Unlocking Door with User Code

Touch screen to wake up lock.

TO LOCK DOOR, wake up lock and press Lockbutton

Deleting a User Code

Touch screen to wake up lock.

Deleting All User Codes

Touch screen to wake up lock.

Additional Programming Functions

Touch screen to wake up lock. Wake up lock before each function.

Programming Symbols

Lock / Clear
Unlock / Programming
Administrator Code

Automatic Lock Function

SET OR CANCEL AUTO LOCK

You can set the lock to automatically close after each time the lock is opened. Time value range = 20 - 900 seconds, enter the following:

Set Auto Lock: Unlock 5 Unlock Time Value Unlock
Hear 1 beep and Light Indicator illuminates green.
To cancel Auto Lock set the time to 00, enter the following:

Cancel Time Value Auto Lock: Unlock 5Unlock 00 Unlock
Hear 1 beep and Light Indicator illuminates green.

TEMPORARILY DISABLE:
While in Auto-Lock mode, unlock door using . Immediately turn the locking knob back AC to the unlocked position. You will hear 1 beep and the light indicator will illuminate green.
The Auto-Lock mode is now disabled.

RESTORE:
To restore the Auto-Lock function, turn the locking knob by hand to the locked position, wait more than 2 seconds or press the Lock button on the touchscreen.

Vacation Mode

With Vacation Mode enabled, the system enters into low-power consumption mode.
During this mode, all buttons and functions will be disabled until they are re-enabled.

ENABLE:

Unlock10Unlock1Unlocklight indicator illuminates green.
Once the door is locked, vacation mode will be engaged and all buttons and functions will be disabled.

DISABLE:
To disable the Vacation Mode, you must press and hold unlock for more than 3 seconds, then input followed by unlock to unlock the door. The light indicator will illuminate red. Vacation Mode is now disabled.

NOTE: If you only press unlock for more than 3 seconds but do not input , the system will remain in Vacation Mode.

Secure Lock-out period

Warning sounds and LED flashes red after 4 incorrect code attempts: Touchscreen shuts down for 60 seconds.

Additional Programming Functions

SOUND ON AND OFF

You can "mute" or turn the "sound on" on your lock by entering the following. (Factory setting is sound on).

Unlock 6 Unlock 1 or 2 Unlock

1 = Sound Off
2 = Sound On

Sound Off (1) - Light Indicator illuminates green.
Sound On (2) - Hear 1 beep and Light Indicator illuminates green.

Restore Factory Settings

To reset the lock to the original factory settings including the Programming Code and all User Codes follow these steps:

1. Remove one battery for 10 seconds.
2. Reinsert the battery and wait for a long and short beep
3. Press Lock 3 times within 3 seconds.
4. The lock will beep and the light indicator will turn green.

Low Battery Warning

Beeps and LED flashes red 7 times. Replace with good quality alkaline batteries.
Note: Removing batteries does not erase active Administrator or User Codes.

Consumer Friendly Message Guide

Troubleshooting

DO NOT RETURN TO STORE!
Problems Installing or Using this Product?
Call Us First!
Contact Us 1-800-860-1677 Ext. 1801 locks@LHLPinc.com
Support hours M-F 8am – 8pm EST

CONSUMER ASSISTANCE

EMAIL: LHLPCustomerService@LHLPinc.com WEBSITE: www.honeywellsafes.com
ADDRESS: Consumer Assistance Dept. LH Licensed Products, Inc., 860 East Sandhill Avenue Carson, CA 90746 USA TELEPHONE: US/Canada 1-800-860-1677 Ext. 1801 (Toll Free)
Mexico 01-800-288-2872 After English voice recording stops you must then enter 800-860-1677 to complete your call. (Toll Free)
Australia 0011-800-5325-7000 (Toll Free)
Germany/New Zealand 00-800-5325-7000 (Toll Free)
Other Countries XX*-310-323-5722 (Toll Charges Apply)
XX*- Dial U.S. Country Code first
CALL CENTER HOURS: US/Canada 8am – 5pm (Pacific**) Mon – Fri (Subject to change)
CALL BACK HOURS: Other Countries 8am – 5pm (Pacific**) Mon – Fri (Subject to change)
Pacific**- Local time in Los Angeles, CA, USA
* Insert correct Country Code
** Local Time based on Los Angeles California USA INTERNATIONAL CALL BACK HOURS:

If you need to speak with a consumer assistant and cannot contact us during the Call Center hours above, please send an email or leave a telephone message, including your Name, Telephone Number and the best time for us to contact you during the Call Back hours above and we will make our every effort to contact you and help answer any of your questions or concerns.

Manufactured by:
LH Licensed Products, Inc.
860 East Sandhill Avenue
Carson, CA 90746
The Honeywell Trademark is used under license from Honeywell International Inc. Honeywell International Inc. makes no representations or warranties with respect to this product.
www.honeywellsafes.com