Table of Contents
Advertisement
Quick Links
MICROWAVE OVEN/HOOD SYSTEM
Please read all instructions thoroughly before installing the Microwave Oven/Hood System. Two people are
recommended to install this product.
If a new electrical outlet is required, its installation should be completed by a qualified electrician before the
Microwave Oven/Hood is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on page 2.
1 MOUNTING SPACE
This Microwave Oven/Hood requires a mounting space
on a wall as shown in Figure 1. It is designed to be used
with standard 12-inch wall cabinets.
If the space between the wall cabinets is 36 or 42 inches,
a Filler Panel Kit can be used to fill the gap. The metal
filler panels come in 3-inch wide pairs. One set is needed
for a 36-inch opening and 2 sets for a 42-inch opening.
White and black are available. See page 8 for ordering
information. The Filler Panel Kit should be installed before
the Microwave Oven/Hood is installed.
OVER THE RANGE
INSTALLATION
INSTRUCTIONS
12"
At least 2"
Backsplash
1
1
15
"
/
2
30"
30" or more from
cooking surface
66" or more from floor
Figure 1
Advertisement
Table of Contents
Related Manuals for Sharp 1490
Summary of Contents for Sharp 1490
- Page 1 MICROWAVE OVEN/HOOD SYSTEM INSTALLATION INSTRUCTIONS Please read all instructions thoroughly before installing the Microwave Oven/Hood System. Two people are recommended to install this product. If a new electrical outlet is required, its installation should be completed by a qualified electrician before the Microwave Oven/Hood is installed.
-
Page 2: Wall Construction
1. If you have any questions about the grounding or electrical instructions, consult a qualified electrician or serviceperson. 2. Neither Sharp nor the dealer can accept any liability for dam- age to the oven or personal injury resulting from failure to observe the correct electrical connection procedures. -
Page 3: Tools Recommended For Installation
4 HOOD EXHAUST DUCT When the hood is vented to the outside, a hood exhaust duct is required. All ductwork must be metal; absolutely do not use plastic duct. Check that all connections are made securely. Please read the following carefully: Exhaust connection: The hood exhaust has been designed to connect to a standard 3-1/4”... -
Page 4: Ventilation System
If there is any damage, do not operate the oven and contact your dealer or SHARP AUTHORIZED SERVICER. 3. Remove and save Screw (A) as shown in Figure 6. - Page 5 (B) HORIZONTAL EXHAUST: Outside Ventilation 1. Remove and save 2 screws from back edge and 1 screw from the top center of Fan Cover Bracket. Remove Fan Cover Bracket by sliding it in the opposite direction of the arrow on the Fan Cover Bracket, as shown in Figure 9.
-
Page 6: Oven Installation
(C) VERTICAL EXHAUST: Outside Ventilation 1. Remove and save 2 screws from back edge and 1 screw from the top center of the Fan Cover Bracket. Remove Fan Cover Bracket by sliding it in the opposite direction of the arrow on the Fan Cover Bracket as shown in Figure 9 on page 5. - Page 7 MOUNTING OVEN TO THE WALL Two people are recommended to attach the Microwave Oven/Hood to the Mounting Plate. 1. Thread the power supply cord through the hole made in the bottom of the top cabinet. 2. Install the oven by sliding it onto the arms of the Mounting Plate.
- Page 8 1. CHARCOAL FILTER (RK-230). Filter is used when hood exhaust is recirculated only. Check with your dealer or order directly from the SHARP Accessories and Supplies Center. Call toll-free 1-800-642-2122. 2. FILLER PANEL KIT. This is available for use when the oven is installed in a 36” or 42” wide opening. The metal filler panels come in pairs, each either 3 or 6 inches wide.