Sharp KB-3401LK Installation Manual
Liquid crystal display camcorder
Hide thumbs
Also See for KB-3401LK:
- Operation manual (40 pages) ,
- Installation manual (8 pages) ,
- Supplemental service manual (60 pages)
Table of Contents
Advertisement
sPECIal WaRnInG
InstallatIon anD sERVICE Must BE PERFoRMED BY a QualIFIED InstallER.
IMPoRtant: saVE thIs InstallatIon Manual FoR loCal ElECtRICal
InsPECtoR's usE.
REaD anD saVE thEsE InstRuCtIons FoR FutuRE REFEREnCE.
ClEaRanCEs & DIMEnsIons
For SAFETY CONSIDERATIONS do not install a range in any combustible cabinetry which is not in
accord with the stated clearances and dimensions on page 2. See Figures 1 and 2.
RanGE MEasuREMEnts ......................................2
ClEaRanCEs anD DIMEnsIons ..............................2
IMPoRtant notEs .............................................2
unPaCkInG anD ExaMInInG YouR RanGE .................3
IMPoRtant saFEtY InstRuCtIons .........................3
30" Freestanding Range
InstallatIon Manual
ElECtRICal ConnECtIons ................................ 3-5
MoDEl anD sERIal nuMBER loCatIon ....................4
antI-tIP ..................................................... 6-7
CaRE, ClEanInG anD MaIntEnanCE ......................7
notEs ..... .......................................................8
Advertisement
Table of Contents
Related Manuals for Sharp KB-3401LK
Summary of Contents for Sharp KB-3401LK
-
Page 1: Table Of Contents
REaD anD saVE thEsE InstRuCtIons FoR FutuRE REFEREnCE. ClEaRanCEs & DIMEnsIons For SAFETY CONSIDERATIONS do not install a range in any combustible cabinetry which is not in accord with the stated clearances and dimensions on page 2. See Figures 1 and 2. -
Page 2: Range Measurements
• Contact surface must be solid and level. Pay special attention to the floor. Be sure it is solid enough for the weight of the range. Check that the floor covering is smooth and flat and that it adheres to the sub-floor solidly. -
Page 3: Unpacking And Examining Your Range
Never leave children alone or unattended in the area where an range is in use. As children grow, teach them the proper, safe use of all ranges. Never leave the oven door open when the range is unattended. -
Page 4: Model And Serial Number Location
Microwave Drawer front. 08/0 Volt connectIon InstRuctIons The range can be set for 208V or 240V. The voltage setting for your range is pre-set at 240V from the factory. Follow these steps to change the voltage setting. - Page 5 KEEP the ground screw, ground plate and go to step 4. Connect the green ground wire lead to the frame of the range using the ground screw and plate as shown in Figure 11. Be sure to install using the same hole in the frame where the ground screw was originally installed.
-
Page 6: Anti-Tip
Anti-Tip bracket and screws packed with the range. Failure to install the Anti-Tip bracket will allow the range to tip over if excessive weight is placed on an open door or if a child climbs upon it. Serious injury might result from spilled hot liquids or from the range itself. - Page 7 • Measure from the countertop to the floor height to determine the height that the back of the range needs to be set at. • Loosen legs and lock nuts to set level of the range. (Note that the lock nuts are only on the rear feet). See Figure 15.
-
Page 8: Care, Cleaning And Maintenance
Refer to your Operation Manual for our service address. Sharp's toll-free telephone number is 1-800-BE-SHARP (1-800-237-4277). Please call or write if you have inquiries about your range product and/or need to order parts.