Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Monitor
  5. SyncMaster 510S
  6. User manual

Samsung SyncMaster 510S User Manual

Samsung syncmaster 510s: user guide
Hide thumbs

Advertisement

Quick Links

Download this manual
510/710

Advertisement

loading

Related Manuals for Samsung SyncMaster 510S

Summary of Contents for Samsung SyncMaster 510S

  • Page 1 510/710...
  • Page 2 Safety Instructions Notational Power Installation Cleaning Other Introduction Unpacking Front Rear Bottom Setup Connecting Your Monitor Base Installation Main > Index On-Screen Display Troubleshooting Check List Q & A Self-Test Feature Check Specifications General Specifications Preset Timing Modes PowerSaver Information...
  • Page 3 Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Do not disassemble Do not touch Main > Safety Instructions > Notational Important to read and understand at all times Disconnect the plug from the outlet Grounding to prevent an electric shock...
  • Page 4 When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the fluorescent substance on the inside of the CRT.
  • Page 5 Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire. Put your monitor in a location with low humidity and a minimum of dust. An electric shock or fire could result inside the monitor.
  • Page 6 Power Installation Clean Other When cleaning the monitor case or the surface of the CRT, wipe with a slightly moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. (Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case.
  • Page 7 Do not use or store inflammable substances near the monitor. This may cause an explosion or fire. Do not try to move the monitor by pulling on the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable.
  • Page 8 Keep the monitor away from any magnetic substances. This may cause discoloring or distortion of the image.
  • Page 9 Unpacking Front Rear Bottom (Some models include a stand attached. ) Please make sure the following items are included with your monitor. If any items are missing, file://\\Ssj\an15vt\ver02\MANUAL\EN\product\index.htm Monitor and Stand contact your dealer. Main > Introduction > Unpacking Power Code...
  • Page 10 6. Power button Note: See PowerSaver functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. Use this button to Exit the active menu or the OSD. These buttons allow you to highlight and adjust items in the menu.
  • Page 11 2. Signal Cable Note: See Connecting Your Monitor Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the video port on your computer, video board, video card, or graphics card.
  • Page 12 Connect the signal cable to the video port on your computer, video board, video card, or graphics card. Connect the power cord for your monitor to the power port on the back of the monitor. You can separate the base from the monitor.
  • Page 13 Your Monitor Base Installation 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the video port on your computer, video board, video card, or graphics card.
  • Page 14 Connecting Your Monitor With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable Base Installation viewing angle. Note: The base is detachable. If your monitor was supplied with the base detached, attach the base as follows.
  • Page 15 2. Align the tabs on the base with the corresponding slots on the bottom of the monitor. 3. Press the base onto the monitor until the tabs are fully engaged in the slots. 4. Push the base toward the front of the monitor until the release latch clicks into the locked position.

  • Page 16: On Screen Display (Osd) Menu System

    On Screen Display (OSD) Menu System 1 E it b tt 1 Exit button: 2,3 Adjust buttons: These buttons allow you to highlight and 4 Menu button: Use this button to Exit the active menu or the thi b tt t E it th OSD.

  • Page 17: How To Adjust

    On Screen Display (OSD) Menu System Menu How to adjust Brightness Adjust the Brightness. With the menu off, push the menu Push the - button or + button until the Brightness screen is displayed. Push the menu button to open the Brightness adjustment screen. Use the + button to increase the brightness or - button to decrease the brightness.
  • Page 18 Push the menu button to open the H-Position adjustment screen. Use the - and + buttons to change the Horizontal position of the monitor’s viewing area. V-Position Follow these instructions to change the Position of the monitor’s entire display.
  • Page 19 Push the - button or + button until the H-Size screen is displayed. Push the menu button to open the H-Size adjustment screen. Use the - and + buttons to change the Horizontal Size of the monitor’s viewing area. V-Size Follow these instructions to change the Size of the monitor’s entire display.
  • Page 20 On Screen Display (OSD) Menu System Menu How to adjust Pincushion Adjust the pincushion setting when the sides of the display are bowed in or bowed out With the menu off, push the menu Push the - button or + button until the Pincushion screen is displayed.
  • Page 21 On Screen Display (OSD) Menu System Menu How to adjust Parallelogram Adjust the parallelogram setting when the display is leaning left or right. With the menu off, push the menu Push the - button or + button until the Geometry screen is displayed.
  • Page 22 On Screen Display (OSD) Menu System Menu How to adjust V-Linearity Adjust the linearity setting when the display image is compressed at the left, right or top, bottom. With the menu off, push the menu Push the - button or + button until the Geometry screen is displayed.
  • Page 23 On Screen Display (OSD) Menu System Menu How to adjust H-Moire A “Moiré” pattern can appear on your screen, looking like a series of concentric circles or arcs. To eliminate this pattern, use the clear moiré adjustments. With the menu off, push the menu Push the - button or + button until the Advanced screen is displayed.

  • Page 24: Video Input Level

    On Screen Display (OSD) Menu System Menu How to adjust Video Input Level Some video cards use video signals higher than 1.0V which causes the display to be very bright. For those video cards, use this feature to select the 1.0V Level. With the menu off, push the menu Push the - button or +button until the Advanced screen is displayed.
  • Page 25 How to adjust Zoom Follow these instructions to get a close-up or a longshot view of the monitor’s viewing area. With the menu off, push the menu Push the - button or + button until the Zoom screen is displayed.
  • Page 26 Recall adjustment screen. Push the + button to select Yes. If you don’t want to reset the monitor, use the - button to select No. Note If you have selected “Yes”, all settings listed above will be reset.

  • Page 27: Display Timing

    Note You can see the frequency(user control mode) used by the user, the polarity of the operational signals, the default frequency(default mode) set when you buy the monitor and the resolution level. OSD Lock/Unlock Push and hold in the menu to Lock the OSD.
  • Page 28 The monitor is in PowerSaver mode. Press a key on the keyboard or move the mouse to activate the monitor and restore the image on the screen. Unlock the OSD by pressing the MENU button for at least 10 seconds.
  • Page 29 Has the video card been set properly? Check the following items if there is trouble with the monitor. 1. Check if the power cord and the cable are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting.
  • Page 30 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. Note: If problems repeatedly occur, contact an authorized service center.
  • Page 31 Do not leave any remains of the detergent nor scratch the case. Do not allow any water to go inside the monitor. Main > Troubleshooting > Q & A Answer...
  • Page 32 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system;...
  • Page 33 1 If th 1. If there are any woofer speakers near the monitor, unplug and relocate the woofer to another room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor.
  • Page 34 Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings.
  • Page 35 This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard.
  • Page 36 If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1.
  • Page 37 Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings.
  • Page 38 This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard.
  • Page 39 If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1.
  • Page 40 Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm Terms...

This manual is also suitable for:

Syncmaster 710s510Syncmaster 710v