Table of Contents
Advertisement
6 Recording status (card slot 1)
Displays the recording status of the SD card in the card slot 1.
: Not target for recording.
f
(flashing): Recognizing the SD card.
f
: The recording is stopped with the recording target SD card is inserted.
f
(flashing): Recognizing the SD card.
f
: Recording.
f
(Flashing red dot): Processing to stop the recording.
f
f [P
]: Recording is stopped with the pre-recording is enabled and the recording target SD card is inserted.
f [P]: Pre-recording is enabled, and the SD card is not inserted in the card slot, or the SD card is not recognized.
f (No display): It is in one of the following conditions.
- The SD card is not inserted.
- The SD card cannot be recognized.
- The [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF], and recording is stopped.
: The [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF], and recording is in progress.
f
7 Remaining recordable capacity and status of the SD card (card slot 1)
Displays the remaining recordable capacity of the SD card and status of the SD card in the card slot 1.
f [0min] to [999min]: Remaining recordable capacity (999 minutes or more is displayed as [999min])
- The display will flash when the remaining recordable capacity becomes two minutes or less.
- During the simultaneous recording, the remaining recordable capacity to be able to perform simultaneous recording (the one with smaller
remaining recordable capacity of the two SD cards) is displayed.
f [WP]: Write protected (the write protection switch on the SD card is at the LOCK side)
f [END]: No remaining recordable capacity (there is no remaining recordable capacity in the SD card)
f [ERR]: The SD card that cannot be recorded is inserted (it is recognized, but cannot be used such as format error, other than SD card, etc.)
f [!SDXC]: The SDXC memory card is not inserted for MOV recording
f (No display): It is in one of the following conditions.
- The SD card is not inserted.
- The SD card cannot be recognized.
- The [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF].
8 Recording status (card slot 2)
Displays the recording status of the SD card in the card slot 2.
: Not target for recording.
f
(flashing): Recognizing the SD card.
f
: The recording is stopped with the recording target SD card is inserted.
f
(flashing): Recognizing the SD card.
f
: Recording.
f
(Flashing red dot): Processing to stop the recording.
f
f [P
]: Recording is stopped with the pre-recording is enabled and the recording target SD card is inserted.
f [P]: Pre-recording is enabled, and the SD card is not inserted in the card slot, or the SD card is not recognized.
f (No display): It is in one of the following conditions.
- The SD card is not inserted.
- The SD card cannot be recognized.
- The [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF].
9 Remaining recordable capacity and status of the SD card (card slot 2)
Displays the remaining recordable capacity of the SD card and status of the SD card in the card slot 2.
f [0min] to [999min]: Remaining recordable capacity (999 minutes or more is displayed as [999min])
- The display will flash when the remaining recordable capacity becomes two minutes or less.
- During the simultaneous recording, the remaining recordable capacity to be able to perform simultaneous recording (the one with smaller
remaining recordable capacity of the two SD cards) is displayed.
f [WP]: Write protected (the write protection switch on the SD card is at the LOCK side)
f [END]: No remaining recordable capacity (there is no remaining recordable capacity in the SD card)
f [ERR]: The SD card that cannot be recorded is inserted (it is recognized, but cannot be used such as format error, other than SD card, etc.)
f [!SDXC]: The SDXC memory card is not inserted for MOV recording
f (No display): It is in one of the following conditions.
- The SD card is not inserted.
- The SD card cannot be recognized.
- The [SYSTEM SETTINGS] menu → [SYSTEM MODE] → [SDI RAW] is set to anything other than [OFF].
10 Two-slot function
Displays the setting status of the recording function using two SD cards.
It is displayed with a slanted line if it is in a condition that cannot perform two-slot recording even if each function is enabled.
f [RELAY]: When relay recording is enabled
f [SIMUL]: When simultaneous recording is enabled
f (No display): When it is standard recording
Chapter 7 Output and Screen Display — Screen status display
– 156 –
Advertisement
Table of Contents
