Maintenance; Protecting The Environment - DeWalt DW304 Manual

E N G L I S H
● Avoid overloading.
Let the blade run freely for a few seconds before starting the
cut. Never switch on the tool when the saw blade is jammed
in the workpiece or in contact with the material.
Prior to operation:
● Mount the appropriate type of saw blade. Use narrow saw blades for
cutting curves. Use fl exible bimetal saw blades for hard-to-reach
positions (e.g. close to walls, etc.).
Switching on and off (fi g. A)
● To run the tool, press the variable speed switch (1). The pressure
exerted on the variable speed switch determines the tool speed.
● To stop the tool, release the switch. Always switch off the tool when
work is fi nished and before unplugging.
Cutting wood
● Clamp the workpiece securely and remove all nails and metal objects.
● Holding the tool with both hands, work with the saw shoe pressed
against the workpiece.
Plunge cutting in wood (fi g. C)
● Rest the saw shoe on the workpiece in such a position that the blade
forms an appropriate angle for the plunge cut.
● Switch the tool on and slowly feed in the blade. Make sure that the
saw shoe remains in contact with the workpiece at all times.
Pocket cuts
● Measure and mark the required pocket cut.
● Using a narrow saw blade rest the bottom of the saw shoe on the
workpiece and make sure that the blade is positioned on the cutting
line. If necessary, e.g. in confi ned spaces, use the outer edge of the
saw shoe as your guideline.
● Switch on the tool and feed the blade into the material at full speed,
holding the tool fi rmly against the workpiece.
D
Dust extraction
● When the tool is used indoor for extended periods of time, use a
suitable dust extractor designed in compliance with the applicable
Directives regarding dust emission.
Cutting metal
● When cutting thin metal always stabilize the workpiece with wood on
both sides. This guarantees clean cuts and prevents damaging of the
material.
● For long, straight cuts draw a line on the workpiece.
● Apply a thin fi lm of lubricant along the cutting line, switch on the tool
and follow the cutting line.
Cutting plastics
● Always work at reduced speed. Carry out a test cut to check whether
the material is sensitive to heat.
d
Cutting masonry
@ When sawing asbestos cement hazardous dust may be
produced. Follow the statutory guidelines and observe the
recommendations issued by the asbestos cement manufacturers.
Sawing up to a projecting edge (fi g. D)
● Using a conventional blade installed upside down, cut up to the
projected edge.
18
Parallel cutting (fi g. E)
With the blade installed in the horizontal orientation, the tool can be
used for parallel cutting close to fl oors, walls or ceilings.
● Make sure that the saw shoe remains in contact with the workpiece
at all times.
Consult your dealer for further information on the appropriate
accessories.

Maintenance

Your D WALT power tool has been designed to operate over a long
E
period of time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Lubrication
● If the tool will not be used for a long period of time, coat the saw
blade with a little oil (e.g. machine oil).
S
Cleaning
Keep the ventilation slots clear and regularly clean the housing with a
soft cloth.

Protecting the environment

Separate collection. This product must not be disposed of
Z
with normal household waste.
Should you fi nd one day that your D
or if it is of no further use to you, do not dispose of it with household
waste. Make this product available for separate collection.
z Separate collection of used products and packaging allows
materials to be recycled and used again. Re-use of recycled
materials helps prevent environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection of electrical
products from the household, at municipal waste sites or by the retailer
when you purchase a new product.
D WALT provides a facility for the collection and recycling of D
E
products once they have reached the end of their working life. To take
advantage of this service please return your product to any authorised
repair agent who will collect them on our behalf.
You can check the location of your nearest authorised repair agent by
contacting your local D WALT offi ce at the address indicated in this
E
manual. Alternatively, a list of authorised D
details of our after-sales service and contacts are available on the
Internet at: www.2helpU.com
WALT product needs replacement,
E
WALT
E
WALT repair agents and full
E