Table of Contents
Advertisement
Quick Links
Z3C Installation Guide [Internal]
This document describes how to install and set up the Z3C teleworker gateway. Additional reference documents are
available online at: www.meraki.com/library/products.
Z3C Overview
The Meraki Z3C is 802.11a/b/g/n/ac and LTE Wireless Security Appliance designed for telecommuting employees and
IT staff. It is also a great all-in-one device to test the capabilities of Meraki's cloud-managed networking. This gateway
provides the following features:
• Support for four LAN connections
• Dual-concurrent 802.11ac radios for wireless connections
• Wall screws and anchors for mounting drywall surface, either vertically or horizontally
Package contents
In addition to the Z3C, the following are provided.
SIM Slot Pin
1
Advertisement
Table of Contents
Related Manuals for Cisco Meraki Z3C
Summary of Contents for Cisco Meraki Z3C
- Page 1 Z3C Overview The Meraki Z3C is 802.11a/b/g/n/ac and LTE Wireless Security Appliance designed for telecommuting employees and IT staff. It is also a great all-in-one device to test the capabilities of Meraki's cloud-managed networking. This gateway provides the following features: •...
-
Page 2: Ports And Status Indicators
The Z3C front panel Ports and Status Indicators The Z3C uses a single LED to inform the user of the device's status. Function LED Status Meaning Power Up/Boot Solid Orange Power is applied Connecting Rainbow Device in process of connecting to the Meraki Dashboard Connected Solid White Fully operational... - Page 3 The Z3C back panel Additional functions on the back panel are described below, from left to right. WAN / Internet port This port provides connectivity to the WAN. LAN ports These 4 ports provide connectivity to computers, printers, access points, or Ethernet switches. A steady green LED indicates bidirectional connectivity, and flashing green indicates traffic.
- Page 4 The Z3C bottom panel Please note that the serial number is located on the product label at the bottom panel of Z3C...
-
Page 5: Mounting Hardware
Connecting to WAN All Meraki Z3C devices must have an IP address. This section describes how to configure your local area network before you deploy it. A local management web service, running on the gateway, is accessed through a browser running... -
Page 6: Setting Up A Static Ip Address
Setting up a static IP address To ensure that the client PC is redirected to the local web service in the following step, you must disable all other network services (ex: wi-fi) on your client machine. Do the following to configure basic connectivity and other networking parameters: 1. - Page 7 10- or 100-Mbps data rates. Power efficiency modes The Meraki Z3C Teleworker Appliance has an off mode and a networked standby or efficient idle mode, both with power consumption less than 12W.
- Page 8 • Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications no expressly approved by Cisco could void the user’s authority to operate this equipment. This Transmitter must not be co-located or operation in conjunction with any other antenna or transmitter.
- Page 9 If the device is going to be operated in the 5.15 - 5.25 frequency range, then it is restricted to indoor environment only. This device meets all other requirements specified in Part 15E, Section 15.407 of the FCC Rules. Industry Canada Statement This Z3C complies with license-exempt RSSs of the Industry Canada Rules.
- Page 10 Taiwan NCC Statement 減少電磁波影響，請妥適使用。 無線資訊傳輸設備避免影響附近雷達系統之操作。 低功率射頻設備的管理辦法 第12條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得 擅自變更頻率、加大功率或 變更原設計之特性 及功能。 第14條 低功率射頻電機之使用不得影響飛航安全及干擾 合法通信；經發現有干擾現象時，應立即用，並改善 至無干擾時方得繼續 使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科及醫療用電波輻射性電機設備之干擾。 低功率射頻電機技術規範 4.7 無線資訊傳輸設備 4.7.6 無線資訊傳輸設備須忍受合法通信之干擾且不得干擾合法通信；如造成干擾，應立即停用，俟無干擾之 虞，始得 繼續使用。 4.7.7 無線資訊傳輸設備的製造廠商應確保頻率穩定， 如依製造廠商使用手冊上所述正常操作，發射的信號 應維持於操作帶中。 在5.25-5.35秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用。電磁波曝露量MPE標準值1mW/cm2，本產品使用時建議應距離人 體20cm。 Statement CS-0438 - 台灣 RoHS 台灣RoHS“限用物質含有情況標示聲明書”網址 www.cisco.com/go/taiwanrohs...