Table of Contents
Advertisement
SETTING YOUR TEMPERATURE
7.
Touch the 'TEMP' icon – this will default to 25C – select your temperature by rotating
the control dial clockwise to scroll through 25, 45, 55, 65, 75, 85 or 100C. When you
have selected the right temperature touch the 'TEMP' icon to lock in your selection.
NOTE: If the 'TEMP' icon is not selected, the machine will be locked after 60 seconds
of no operation.
BEGIN YOUR HOTCUP™ DISPENSE
8.
To activate the Dispense press the control dial once. The water will dispense in a
continuous flow of water – when it comes to the end of the volume dispense the unit
will provide a series of countdown beeps. You can hear beep sound when turning the
control dial for temperature and volume selection. To activate/de-active the sound,
touch and hold 'TEMP' and
for 3 seconds. If you delay selecting anything for more
than 60 seconds the machine will enter 'Lock' mode. To re-activated touch the
seconds – as it will default to 200ml, 25C after unplug.
STOPPING YOUR HOTCUP
WATER DISPENSER
™
If you have started the HotCup™ water dispense and then decide you want to stop your
HotCup™ water dispense for any reason, simply press and hold the control dial. This
may take a few seconds as the flow through heater will exit some water. You can also
stop water that is being dispensed by pressing and holding the control dial.
CUSTOMISING YOUR INSTANT HOTCUP™ WATER DISPENSE VOLUME
You can customise your volume to suit your favourite cup or mug, choose any volume
between 150ml – 1400ml.
How to customise your dispense
1.
Ensure the control panel is 'unlocked' by touching the
2.
Select your chosen temperature ahead of customising your volume.
3.
Touch the 'TEMP' icon – this will default to 25C – select your temperature by rotating
the control dial clockwise to scroll through 25, 45, 55, 65, 75, 85 or 100C.
4.
When you have selected the right temperature touch the 'TEMP' icon again to set.
Now customise your volume:
5.
Ensure you have a vessel, cup or mug large enough for your customisable volume
6.
Press and hold the 'VOL' icon for 3 seconds, the 'VOL' illumination will cease, swiftly
'double-click' the control dial to begin the dispense.
7.
Once you have dispensed the volume you want press the control dial once to
8
VKT241_23EM1 (UK).indd 8-9
VKT241_23EM1 (UK).indd 8-9
for 3
for 3 seconds.
cease the dispense. There will be a couple of seconds release before the unit stops
dispensing.
8.
Your customised volume is now memorized. To dispense the customised volume,
press the control dial once. You can select different temperature in this function.
9.
To De-activate and remove the customised setting press and hold 'VOL' for 3 seconds.
NOTE: During dispense only the temperature will display.
NOTE: If the unit is switched off at the power socket your memorised volume will default
back to the main setting and will need to be reset.
LOW/NO WATER SIGNAL
When the unit is low on water during operation the unit will immediately cut off the power
to the heater pipe and the water pump will pump for 15 seconds. If there is no water the
buzzer will sound 5 times to end the operation and the unit display will read E0.
LOCKING/UNLOCKING THE INSTANT HOTCUP™
1.
To un-lock the HotCup™ press and hold the child lock (
HotCup™ will unlock. After unlocking the HotCup™ will return to the temperature
and water level before locking.
2.
To lock the HotCup™, press and hold the child lock (
HotCup™. The (
) will remain the only illuminated icon.
CLEANING
Always switch off and unplug your HotCup
completely cool before cleaning. Never immerse the main body, power base, power
cord or plug in water or any other liquid. Do not use harsh abrasives, chemicals or
oven cleaners.
Emptying your HotCup™ water dispenser
1.
Remove the large water tank and place on the counter.
2.
Remove the water filter holder.
3.
Take the large water tank to the sink and pour out the excess water.
4.
Replace the water filter holder in to the water tank.
5.
Replace the large water tank on the HotCup™ main housing.
Your HotCup™ water dispenser is now empty.
If your HotCup™ water dispenser will not be used for an extended period (e.g. if you are
on holiday), we recommend that you first empty it.
Before using your HotCup™ water dispenser again, carry out several boil cycles
discarding the water each time.
Cleaning
Clean the exterior surface of your HotCup™ water dispenser with a damp cloth and then
polish it with a soft, dry cloth. Do not use steel wool pads or harsh/abrasive cleaners.
) for 3 seconds and the
) for 3 seconds to lock the
water dispenser and allow it to
™
9
2023/3/8 09:39
2023/3/8 09:39
Advertisement
Table of Contents
