Advertisement
COMPATIBLE BATTERY PACKS (NOT INCLUDED)
L1820R
A18B4
L1820S
L1840R
A18FB2
A18FB4
L1825R
L1850R
L1830R-X5
A18FB5
Use AEG 18V battery and charger only
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, fire, and/or serious injury.
Save all warnings and instructions for future reference.
IMPACT WRENCH SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give the
operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Clamp workpiece with a clamping device. Unclamped workpieces
can cause severe injury and damage.
The product will restart automatically if stalled. Switch off the
product immediately if it stalls. Do not switch on the product again
after it has stalled. Switching it on again, can cause a kickback with
high reaction force. Determine why the product has stalled and
rectify it, paying heed to the safety instructions."
When working in walls, ceiling, or floor, take care to avoid electric
cables and gas or waterpipes.
The dust produced when using the product may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection
mask.
Dust created by operating the product can cause respiratory
injury. Wear appropriate respiratory masks with filters suitable for
protecting against particles from the material being worked on.
Ensure adequate workplace ventilation. Do not eat, drink, or smoke
in the work area.
Damage to eyes from flying dust and debris particles. Always wear
suitable eye protection.
Do not switch on the product again after it has stalled. Switching it
on again, can cause a kickback with high reaction force. Determine
why the product has stalled and rectify it, paying heed to the safety
instructions. If necessary, remove the insertion tool.
Always wear goggles when using the product. It is recommended
to wear gloves, sturdy non slipping shoes and apron.
Always use the protective shields on the product.
Remove the battery pack before starting any work on the product.
The product will restart automatically if stalled. Turn off the product
immediately if it stalls. Do not turn on the product again while it is
Ambient temperature range for tool during operation is between
0°C and 40°C.
Ambient temperature range for tool storage is between 0°C and
40°C.
The recommended ambient temperature range for the charging
system during charging is between 10°C and 38°C.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING! To reduce the risk of fire, personal injury, and
product damage due to a short circuit, never immerse your tool,
battery pack or charger in fluid or allow a fluid to flow inside them.
Corrosive or conductive fluids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., can
cause a short circuit.
Remove the battery pack before starting any work on the product.
Do not dispose of used battery packs in the household refuse or
by burning them. AEG Distributors offer to retrieve old batteries to
A18OB6
protect our environment.
L1860R
Do not store the battery pack together with metal objects (short
L1860R-X5
circuit risk).
L1890R
Use only System AEG chargers for charging System AEG battery
packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it off immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
ADDITIONAL SAFETY WARNING
Switch the device off immediately if the insertion tool stalls! Do not
switch the device on again while the insertion tool is stalled, as
doing so could trigger a sudden recoil with a high reactive force.
Determine why the insertion tool stalled and rectify this, paying
heed to the safety instructions.
The possible causes may be:
●
●
●
RESIDUAL RISKS
Even when the product is used as prescribed, it is still impossible
to completely eliminate certain residual risk factors. The operator
should pay particular and additional attention to these points in
order to reduce the risk of serious personal injury.
• Injury to hearing – Wear suitable ear protection and limit
exposure.
• Injury to sight – Wear protective eye shields or goggles when
using the product.
• Injury caused by vibration – Hold the tool by the designated
handles and limit exposure to vibration. See "RISK
REDUCTION".
• Electric shock after contact with hidden wires – Hold the
product only by insulated surfaces.
• Respiratory injury – Dust created by operating the product,
wear suitable protection dependent on type of dust.
RISK REDUCTION
It has been reported that vibrations from handheld tools may
contribute to a condition called Raynaud's Syndrome in certain
individuals. Symptoms may include tingling, numbness and
blanching of the fingers, usually apparent upon exposure to cold.
Hereditary factors, exposure to cold and dampness, diet, smoking,
and work practices are all thought to contribute to the development
of these symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
• Keep your body warm in cold weather. When operating the unit
wear gloves to keep the hands and wrists warm. It is reported
that cold weather is a major factor contributing to Raynaud's
Syndrome.
• After each period of operation, exercise to increase blood
circulation.
• Take frequent work breaks. Limit the amount of exposure per
day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about these
symptoms.
SPECIFIED CONDITIONS OF USE
The impact driver is intended to be used only by adults who have
read and understood the instructions and warnings in this manual,
and can be considered responsible for their actions.
It is tilted in the work piece to be machined
It has pierced through the material to be machined
The power tool is overloaded
9
Advertisement
