Eaton PVM Series Installation & Maintenance Information

Pro-Champ LED Luminaires
PVM Series Industrial LED Lighting
Installation & Maintenance Information
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
APPLICATION
Luminaire construction is designed for use indoors and
outdoors in marine and wet locations, where moisture, dirt,
corrosion, vibration, and rough usage may be present.
PVM supplied with a choice of voltages:
• 100-277VAC 50/60 Hz
• 108-250VDC
• 347V
• 480V
WARNING
To avoid the risk of fire, explosion or electric
shock, this product should be installed, inspected
and maintained by a qualified electrician only, in
accordance with all applicable electrical codes.
WARNING
To avoid electric shock:
• Be certain electrical power is OFF before and during
installation and maintenance.
• Luminaire must be supplied by a wiring system for
the specific hazardous locations suitable per local
code with an equipment grounding conductor.
To avoid burning hands:
• Make sure LEDs and drivers are cool to touch when
performing maintenance.
INSTALLATION
MOUNTING
1. Mount the cover module in its support position.
• Ceiling and wall mount: mark and drill desired location
on mounting surface. Secure with 1/4" (6mm) bolts
or lag screws (not provided).
• Pendant, stanchion mount: securely thread onto the
appropriate NPT size conduit. Tighten set screw
located in the conduit hub. See Figure 1.
• Crouse-Hinds HTL thread lubricant must be added to
the conduit threads to prevent water from entering
the fixture.
FIGURE 1
Open
Hinge
Set-screw
Ground Wires
IF 1628 • 05/22 Copyright © 2022, Eaton's Crouse-Hinds Division
IF 1628
• Wet location, Type 4X
• UL1598 Luminaires, UL1598A Marine
• IP66
• cUL
Directive EU 2019/2022
This product contains a light source of energy efficiency
class D or E.
WARNING
To avoid explosion:
• Make sure the supply voltage is the same as the
rated luminaire voltage.
• Do not install where the marked operating
temperatures exceed the ignition temperature of the
hazardous atmosphere.
• Do not operate in ambient temperatures above those
indicated on the luminaire nameplate.
• Use only replacement parts from Crouse-Hinds.
• Use proper supply wiring as specified on the
luminaire nameplate.
• All surfaces must be clean.
• Before opening wiring compartment, electrical power
to the luminaire must be turned off and area must be
free from hazardous atmosphere. Keep tightly closed
when in operation.
• To minimize the risk from electrostatic discharge,
when cleaning, wipe the lens with a clean, damp
cloth.
• LED compartment is non serviceable. Do not open.
WIRING
1. Pull field wiring into cover module.
2. Close all unused conduit entries with conduit
plugs provided. To prevent galling and to ensure
water-tightness, lubricate conduit plugs with
Crouse-Hinds HTL lubricant before installing, and secure
wrench-tight with at least five (5) full threads engaged
(42-52 ft.-lb. for 3/4" plugs, and 58-68 ft.-lb. for 1" plugs).
3. Hang LED luminaire on the cover module hinge hook.
See Figure 2a.
4. Connect supply wires to luminaire wire leads or terminal
block per the attached wiring diagrams using methods
that comply with all applicable codes. See Figure 2b.
Tighten all electrical connections.
5. Close driver housing onto cover module, making sure
that all wires are safely
inside driver housing.
Tighten captive closing
screw to 30 in.-lbs. (3.4
N-m). Ensure two (2)
bosses on driver housing
are in contact with cover
module.
6. Turn power on.
FIGURE 2a
DIAGRAM #1:
WIRING DIAGRAM FOR:
5L, 7L & 9L
DIAGRAM #2:
WIRING DIAGRAM FOR:
PVM3L SERIES
DIAGRAM #3:
WIRING DIAGRAM FOR:
347 OR 480 VOLT TRANSFORMER
LINE
VOLTAGE
DIAGRAM #4:
WIRING DIAGRAM FOR:
347 OR 480 VOLT TRANSFORMER
ON PVM11L
GROUND
NOTE: Ground wire must be added to mounting plate
ground lug and to lugs on entry hubs. Ground wire included.
Page 1
IF 1628 • 05/22
L1 BLK
ACL(BLK)
LINE
DRIVER
VOLTAGE INPUT
N WHT
ACN(WHT)
GRN
(GND)
DRIVER
BLK ACL(BLK)
INPUT
WHT
ACN(WHT)
GRN (GND)
GROUND
PE GRN
L1 BLK ACL(BLK) DRIVER
LINE
VOLTAGE INPUT
N WHT
ACN(WHT)
GRN GND
GROUND PE GRN
LINE
190/270 V BLK ACL(BLK)
347/480 V
VOLTAGE
L1
DRIVER # 1
INPUT
WHT
ACN(WHT)
N
TRANSFORMER GRN GND (SEE NOTE 4 SHT 1)
BLK
ACL(BLK)
INPUT DRIVER # 2
COM COM
WHT
ACN(WHT)
GRN GND (SEE NOTE 4 SHT 1)
GRN
PE
GROUND
BLK DRIVER # 1
347/480 V 190/270 V ACL(BLK)
L1
INPUT
WHT
ACN(WHT)
N TRANSFORMER
DRIVER # 2
BLK ACL(BLK)
INPUT
COM COM WHT
ACN(WHT)
PE
GRN
BLK ACL(BLK)
INPUT
WHT
ACN(WHT)
DENOTES CONNECTION
CLOSED END CRIMP CONNECTOR
PER BOM
DENOTES WIRE CROSS
OVER, NOT CONNECTION POINT
FIGURE 2b
Copyright © 2022, Eaton's Crouse-Hinds Division
RED or PURPLE RED
V+(RED)
OUTPUT
BLK
BLK
V-(BLK)
PVM5L
PVM7L
PVMV9L
V+(RED) RED or PURPLE RED
OUTPUT
BLK BLK
V-(BLK)
V+(RED) RED RED
PVM3L
OUTPUT
V-(BLK)
BLK BLK
RED or PURPLE RED
V+(RED)
OUTPUT
BLK
BLK
V-(BLK)
PVM3L
PVM5L
PVM7L
PVM9L
RED or PURPLE RED
V+(RED)
OUTPUT
BLK
BLK
V-(BLK)
GREY RED
V+(GREY)
OUTPUT
BLK BLK
V-(BLK)
GREY RED
V+(GREY)
OUTPUT PVM11L
BLK BLK
V-(BLK)
DRIVER # 3
RED
GREY
V+(GREY)
OUTPUT
BLK BLK
V-(BLK)
Page 2