Other Error Messages - Canon PIXMA mini260 Service Manual

15 times USB Host VBUS
overcurrent
16 times Battery error
17 times Battery error
20 times Other hardware error
Alarm LED lit ROM error
Alarm LED lit RAM error
*1: Before replacement of the logic board ass'y, check the ink absorber counter value (by service test print or EEPROM information
print). If the counter value is 7% or more, also replace the ink absorber kit (QY5-0182) when replacing the logic board ass'y. If
the counter value is less than 7%, register the current ink absorber counter value to the replaced new logic board instead.
3. Adjustment / Settings, (5) Service mode, for details.]

2-3. Other Error Messages

Message on the LCD
The print head lock lever is not properly
applied. Open the cover and press the
lock buttons on both ends of the lever.
Read/write attribute is not available
during battery operation.
Cannot print via wireless
communication.
- No photo data
- Unsupported photo data
- Photo data too large
There are no photos in memory card.
The value exceeds the number of copies
you can print.
Memory card is not set. Insert the card
after checking the direction.
DPOF information is not saved in the
memory card.
Change the setting after removing the
card.
The card is currently write-enabled. Set
to read-only mode before performing
operation.
[9000] The USB Host VBUS is overloaded.
[A100] The thermistor is faulty, or the battery
temperature exceeded the specified value.
[A000] The microcomputer built in the battery got
faulty due to short circuit, etc.
[6500] The PCI bus error is detected by the ASIC.
The check sum value is incorrect in the
ROM check at hard-power-on.
An error is detected in the RAM check at
hard-power-on.
Cause
The print head lock lever was not completely
lowered, contacting the printer cover.
To prevent data loss (in case the printer power
turns off due to exhaustion of the battery
power), writing to a memory card cannot be
performed.
The image size was too large, or the image file
was not supported.
Supported image files are not in the memory
card.
During selecting images or specifying the
number of copies, the total print quantity
exceeds the prescribed value of 999.
The memory card is not inserted in the slot
properly.
DPOF print was selected in the menu, but no
DPOF files are contained in the memory card.
With a memory card inserted in the slot,
change of the Read/Write attribute was
attempted.
With the memory card set to the Read/write
mode, Card Direct printing operation was
attempted from the menu.
1-6
- Logic board ass'y (QM3-0110)
- Portable Kit LK-60
- Logic board ass'y (QM3-0110)
- Portable Kit LK-60
- Logic board ass'y (QM3-0110)
- Logic board ass'y (QM3-0110)
- Logic board ass'y (QM3-0110)
- Logic board ass'y (QM3-0110)
Solution
Push the lever to fit it in place, and close the
printer cover.
Connect the printer to the AC power supply.
Change the image, and try wireless
communication again.
A temporary error.
- Confirm that supported image files are in the
memory card.
- Images with double-byte characters used in
the file name (or folder name) may not be
recognized. Change the file (or folder) name
so that it contains only single-byte
alphanumeric characters.
- If images are edited on the computer, print
them from the computer.
A temporary error. The last operation before
the error is cancelled, and the total print
quantity returns to the value before the error.
Set a memory card properly.
A temporary error. The LCD automatically
returns to the display before the error
occurrence.
A temporary error. Remove the memory card,
then change the Read/Write attribute.
A temporary error. Remove the memory card,
change the memory card setting to Read-only,
then perform Card Direct printing.
*1
*1
*1
*1
*1
*1
[See 3-