Related Manuals for NEC Aspire ISDN PRI
Summary of Contents for NEC Aspire ISDN PRI
- Page 1 Aspire ISDN - PRI Technical Support Web Site: http://ws1.necii.com (registration is required)
- Page 2 No representation is made that this manual is complete or accurate in all respects and NEC Unified Solutions, Inc. shall not be liable for any errors or omissions.
-
Page 3: Table Of Contents
Table of Contents Section 1 ............1 ISDN PRI Features . - Page 4 Table of Contents Program 10 : System Configuration Setup......... . . 42 10-03 : PCB Setup .
- Page 5 Table of Contents Program 22 : Incoming Call Setup ..........97 22-01 : System Options for Incoming Calls .
- Page 6 Table of Contents Table of Contents P/N 92000PRI04...
-
Page 7: Section 1
Section 1 ISDN PRI Features Section 1 ISDN PRI Features Section 1: ISDN PRI Features Aspire ISDN PRI Manual... - Page 8 Section 1 ISDN PRI Features Aspire ISDN PRI Manual...
-
Page 9: Introduction To Isdn
!! Important !! ISDN is an emerging technology on the leading edge of international digital communication's net- working. Always check with your NEC Unified Solutions Technical Service Representative before setting up your ISDN application. Working together will ensure maximum compatibility and reliable ISDN performance. - Page 10 Introduction to ISDN About ISDN Aspire ISDN PRI Manual...
-
Page 11: Isdn Features
8COIU PCBs installed for trunks 1-8 and 17-24, the T1/PRI PCB will use trunks 25-48. The T1/PRI Interface cannot use trunks 9-16 (even if available) since they are not part of a consecutive block of 24 trunks. Aspire ISDN PRI Manual... - Page 12 Connecting a PRI/E1 (2.048Mb/s) line. SW101 T-Bus Connection S-Bus Connection PRI (1.544Mb/s) (4 bit dip switch) T1 (1.544Mb/s) PRI (2.048Mb/s) (4 bit dip switch) (Cont’d) E1 (2.048Mb/s) CN11 Normal Idle Loop Used with Loop Back testing only. Aspire ISDN PRI Manual...
- Page 13 RxD (T) ally-shielded twisted pair, rated at 100 ohms TxD (R) TxD (R1) at 1 MHz). TxD (T) TxD (T1) 3, 6 No Connection 3, 6 No Connection 7, 8 No Connection 7, 8 No Connection Aspire ISDN PRI Manual...
- Page 14 931 CSU, connect the cable to the ‘T1 NETWORK’ connector on the back panel of the CSU. Connect the opposite end of the NETWORK cable to the telco connection. 11. Replace the cover and tighten the two captive screws on the right side of the cabinet cover. Aspire ISDN PRI Manual...
- Page 15 INPUT: Satellite 931 LOCAL (TI) 24-48 VDC TxD data (R) NETWORK EQUIPMENT .2A MAX. TxD data (T) 3, 6 No connection 7, 8 No connection RJ48C-toRJ48C Cable (ships with Satellite 931 CSU) Telco Line RJ48 Jack Aspire ISDN PRI Manual...
- Page 16 ISDN Features Primary Rate Interface (PRI) Installation - For Your Notes - Aspire ISDN PRI Manual...
-
Page 17: Primary Rate Interface (Pri), Answering Calls
15-01-04 : Basic Extension Data Setup - ISDN Caller ID. If this option is to be enabled, then it must also be enabled for the BRI or PRI PCB in 10-03-05 : PCB Setup - CLIP Information. Aspire ISDN PRI Manual... -
Page 18: Conditions
All 23 circuits on the PRI PCB must be identically programmed since any call sent to the PRI PCB can appear on any circuit. Default Setting Once set, PRI trunks ring extension 301 and flash at all other extensions just like other trunk calls. Aspire ISDN PRI Manual... -
Page 19: Programming
ID number (0-50). short-haul (0) or long-haul (1). In 10-03-13, select the loss-of- signal detection limit. In 10-03-14,select the service protocol to be used (0=keypad facility, 1=specified protocol for Aspire). Continued on the following page. Aspire ISDN PRI Manual... - Page 20 Define the extension's Class of Service in 20-06-01. In 35-02-16, enter '0' to print the trunk name Is SMDR used? assigned in 14-01-01 or enter '1' to print the received dialed number. Continued on next page. Aspire ISDN PRI Manual...