Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NETGEAR EN308TC
Summary of Contents for NETGEAR EN308TC
-
Page 2: Start Here
Start Here Start Here Features Features Model EN308 Ethernet Hub Installation Guide... -
Page 3: Package Contents
Model EN308 100M On = Link Blinking = Activity Normal/Uplink 100-240 VAC, 50-60Hz 0.2A max. BNC 50 Power terminator cord BNC T-connector Mounting kit Installation guide, Warranty & Owner Registration Card, and Support Information Card Model EN308 Ethernet Hub Installation Guide... -
Page 4: Product Illustration
There is incoming data on the port. The port is partitioned because of excessive collisions. There is incoming data on the BNC port. The BNC port is partitioned because of excessive collisions. Ethernet Hub Installation Guide EN308TC... - Page 5 BNC port Power receptacle 100-240 VAC, 50-60Hz 0.2A max. Part (Partition) The link between this port and the connected port is good. There is incoming data on the port. The port is partitioned because of excessive collisions. Ethernet Hub Installation Guide...
-
Page 6: Install The Hub
Power Adequate power source within 6 feet (1.83 m). Wiring hardware Wiring hardware, such as punchdown blocks or patch panels, should be complete before installing the hub. Install the Hub 2. Install the Hub Model EN308 Ethernet Hub Installation Guide... -
Page 7: Connect A Pc To The Hub
3. Connect a PC to the Hub Connect a PC to the Hub Note: Model EN308 Ethernet Hub Installation Guide... -
Page 8: Connect The Hub To A Network
4. Connect the Hub to a Network Connect the Hub to a Network Connecting Port Connecting Device on the Hub Ports 1–7 PC, server, or router Ports 1–7 Hub or switch Set the Normal/Uplink Push Button Connecting Port Connecting Device... - Page 9 Cascade the Hub Using the 10BASE-T Ports 100M Normal Normal/Uplink Model EN108 EN108 10 BASE-T HUB Model EN104 Uplink Note: 100M Normal/Uplink Normal 100M Uplink Normal/Uplink 100M Normal/Uplink Uplink Model EN308 Model EN308 On = Link Blinking = Activity 100-240 VAC, 50-60Hz 0.2A max.
- Page 10 Connect to a Network Using the BNC Port BNC T- connector BNC 50 terminator BNC 50 terminator Note: Model EN308 Ethernet Hub Installation Guide...
-
Page 11: Verify The Installation
5. Verify the Installation Verify the Installation Network Interface Cards Hub Integrity Model EN308 Ethernet Hub Installation Guide... -
Page 12: Troubleshooting Information
If the network is extremely busy, you may have to segment the network with an Ethernet switch such as a NETGEAR Ethernet switch or to upgrade your network to Fast Ethernet operation. Make sure the correct UTP cables are used. See the tables in the installation section of this guide for cable use and Normal/Uplink push button information. -
Page 13: Twisted Pair Cables
Twisted Pair Cables Twisted Pair Cables Twisted Pair Cables Straight-through Uplink or twisted pair cable MDI port Normal or twisted pair cable MDI-X port Model EN308 Normal or MDI-X port Crossover Normal or MDI-X port Ethernet Hub Installation Guide... - Page 14 BNC Connector BNC connector Center conductor terminator Model EN308 12345678 Uplink Assignment: Port 8 Output Transmit Data + Output Transmit Data - Input Receive Data + Input Receive Data - Not used Ground shield BNC T-connector Ethernet Hub Installation Guide...
-
Page 15: Technical Specifications
94 by 101 by 28 mm 0.74 lb (0.34 kg) 0 to 40 C (32 to 104 F) 90% maximum relative humidity, noncondensing IEC 801-2, Level 2/3/4 IEC 801-3, Level 2 IEC 801-4, Level 2 IEC 801-5, Level 2 Ethernet Hub Installation Guide... - Page 16 Voluntary Control Council for Interference (VCCI) Statement Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice EN 55 022 Statement Canadian Department of Communications Radio Interference Regulations Règlement sur le brouillage radioélectrique du ministère des Communications Model EN308 Ethernet Hub Installation Guide...
- Page 17 Model EN308 Ethernet Hub Installation Guide...