HIKVISION 0300P Series Quick Start Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Switch
  5. 0300P Series
  6. Quick start manual
HIKVISION 0300P Series Quick Start Manual

HIKVISION 0300P Series Quick Start Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
100 Mbps PoE Switch
Quick Start Guide
UD29448B-A

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION 0300P Series

Summary of Contents for HIKVISION 0300P Series

  • Page 1 100 Mbps PoE Switch Quick Start Guide UD29448B-A...

  • Page 2: Applicable Models

    Preface Applicable Models This manual is applicable to 0300P series 100 Mbps PoE switches. Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement important points of the main text.

  • Page 3: Product Introduction

    1 Introduction 1.1 Product Introduction 0300P series 100 Mbps PoE switches are layer 2 PoE switches, providing advanced PoE power supply technology on the basis of high-performance access. The devices support up to 300 m long- range transmission (EXTEND mode), and feature high-priority ports to ensure preferential network transmission in key service areas of users.
  • Page 4 0326P series switches (with indicator panels) feature twenty-four 10/100 Mbps PoE RJ45 ports and two gigabit combo ports. Note ● The front panels of 0326P series switches (without indicator panels) are similar to those of 0318P series switches (without indicator panels). The only difference is that 0326P series switches feature twenty-four 10/100 Mbps PoE RJ45 ports.
  • Page 5 Gigabit RJ45 Port Solid on: The port is  Indicator (when the connected. devices feature Flashing: port  only one combo transmitting data. port G1/G1-F or Unlit: port  when gigabit RJ45 disconnected or connection port is abnormal. connected) Solid on: The gigabit SFP ...
  • Page 6 When the DIP switch is  switched to “OFF”, port isolation is disabled. Ports communicate with each other. Enable disable watchdog. When the DIP switch is set  to “ON”, PoE watchdog is enabled to automatically detect device connection statuses of corresponding ports and restart ports in PoE Watchdog DIP case...

  • Page 7: Rear Panel

    ● Ports supporting long-range transmission vary with device models. Ports 9 to 16 of 0318P series switches and ports 17 to 24 of 0326P series switches support up to 300 m network transmission. ● Ports supporting port isolation vary with device models. Ports 1 to 16 of 0318P series switches and ports 1 to 24 of 0326P series switches support port isolation.

  • Page 8: Rack-Mounted Installation

    Note Ensure that the distance between the two screws equals to the ● distance between the two hanging holes. Set aside at least 4 mm of the screw bodies outside the wall. ● 3. Align the hanging holes with the screws, and hang the device on the screws.
  • Page 9 Note The grounding terminal is on the rear panel or side panel of the device. The actual device prevails. 3.1.1 With Grounding Bar If a grounding bar is available at the installation site, follow the steps below. Steps 1. Connect one end of the grounding cable to the binding post on the grounding bar.
  • Page 10 RJ45 Port Connection 3.3 Connect SFP Optical Module Connecting an SFP optical module is supported when the device has a fiber optical port or a combo port. Steps Caution Single-Mode optical module needs to be paired for use. ● Do not bend an optical fiber (curvature radius ≥ 10 cm) overly. ●...

Table of Contents