Table of Contents
Advertisement
Quick Links
Gas Electro-Mechanical Valves
Please read the operating and mounting instructions before using the equipment. Install the
equipment in compliance with the prevailing regulations.
Bedrijfs- en montagehandleiding voor gebruik goed lezen! Apparaat moet volgens de geldende
voorschriften worden geïnstalleerd.
Lire les instructions de montage et de service avant utilisation! L'appareil doit imperativement
être installé selon les règlementations en vigueur.
Betriebs- und Montageanleitung vor Gebrauch lesen! Gerät muß nach den geltenden
Vorschriften installiert werden.
MANUFACTURER AND IMPORTER ADDRESSES
Below are the addresses and contact information for the Honeywell – Maxon manufacturing location and European sales office. The
European sales office serves as the importer and EU manufacturer's representative under the EU New Legislative Framework (NLF).
MUNCIE, INDIANA, USA – MANUFACTURER
201 East 18th Street
P.O. Box 2068
Muncie, IN 47307-0068
Tel: 765.284.3304
Fax: 765.286.8394
INSTRUCTION MANUAL
EUROPEAN SALES OFFICE –
IMPORTER
BELGIUM
Maxon International BVBA
Luchthavenlaan 16-18
1800 Vilvoorde, Belgium
Tel: 32.2.255.09.09
Fax: 32.2.251.82.41
32M-95001-02
Advertisement
Table of Contents
Related Manuals for Honeywell MAXON SMA11
Summary of Contents for Honeywell MAXON SMA11
- Page 1 MANUFACTURER AND IMPORTER ADDRESSES Below are the addresses and contact information for the Honeywell – Maxon manufacturing location and European sales office. The European sales office serves as the importer and EU manufacturer's representative under the EU New Legislative Framework (NLF).
- Page 2 GAS ELECTRO-MECHANICAL VALVES WARNING Nameplate and abbreviations The installation, operation and maintenance instructions contain important information that Consult the nameplate of your valve. This lists the must be read and followed by anyone operating maximum operating pressure, temperature limitations, or servicing this product. Do not operate or voltage requirements and service conditions of your service this equipment unless the instructions specific valve.
-
Page 3: Component Identification
GAS ELECTRO-MECHANICAL VALVES Component identification Automatic (motorized) valve Manual valve Model designation Model designation SMA11, CMA11, SMA21, CMA21 SMM11, CMM11, SMM21 1) Access cover screws 2) Access cover 3) Visual indication 4) Mainbase 5) Nameplate 6) Actuator bolts 7) Flow arrow 8) Valve body Automatic (motorized) valve - 4”... -
Page 4: Auxiliary Features
GAS ELECTRO-MECHANICAL VALVES 2. Properly support and pipe the valve in the direction of 6. All access cover plate screws should be tightened the flow arrow on the valve body. Valve seats are direc- using an alternate cross-corner tightening pattern to tional. - Page 5 GAS ELECTRO-MECHANICAL VALVES ACTUATOR ASSEMBLY ROTATION 13. Replace and secure terminal block cover plate and place valve in service. FIELD INSTALLATION OF VALVE POSI- WARNING TION SWITCH MAXON electro-mechanical valves should be ordered in a configuration compatible with General planned piping. If valve orientation is not correct, the actuator assembly can be rotated in 90°...
-
Page 6: Mounting Brackets
GAS ELECTRO-MECHANICAL VALVES Fig. 1 Fig. 2 Fig. 3 Manual reset actuator Automatic reset actuator Automatic reset actuator 3/4” - 3” S Models 2-1/2” C - 4” C Models and 6” S Model 4” & 6” H Models TO CLUTCH #1 BLACK TO TERMINAL #1 BLACK TO MOTOR... - Page 7 GAS ELECTRO-MECHANICAL VALVES Tandem arrangements (for simultaneous opening of main and blocking valves) 6. Draw free end of chain and tension spring together so that as much slack as possible is eliminated, then Installation instructions for tandem arrangements insert the open eye of the spring “S” hook through the link in the chain that will most nearly maintain this 1.
-
Page 8: Maintenance Instructions
GAS ELECTRO-MECHANICAL VALVES MAINTENANCE INSTRUCTIONS Actuator assembly components require no field lubrication and should never be oiled. MAXON electro-mechanical valves are endurance tested Auxiliary switches, solenoids, motors, clutches or circuit far in excess of the most stringent requirements of the boards may be replaced in the field. - Page 9 GAS ELECTRO-MECHANICAL VALVES FITTING CERTIFICATE Conform to all applicable provisions of the European Gas Appliance Directive. Maxon Corporation Certification: Product Identification Number C87BQ83 Address: applies 201 E. 18th Street EC Surveillance: GL Industrial Services (Notified Body Muncie, IN 47302 Number 0087) This certificate issued by: Maxon Corporation Declare that all fittings produced at the above address Name: Lora Davis...
- Page 10 GAS ELECTRO-MECHANICAL VALVES For More Information The Honeywell Thermal Solutions family of products includes Honeywell Combustion Safety, Eclipse, Exothermics, Hauck, Kromschröder and Maxon. To learn more about our products, visit ThermalSolutions.honeywell.com or contact your Honeywell Sales Engineer. Honeywell MAXON branded products...