Chapter 7 Specifications - Hitachi SH1 Series Basic Manual

Chapter 7

Chapter 7 Specifications

7.1 Specifications
Model name
00041 00054 00083 00126 00175 00250 00310 00400 00470 00620 00770 00930 01160 01470 01760 02130 02520 03160
SH1-*****-H
ND standard capacity
007
SH1-***/****H
Applicable
VLD 1.5
Motor ca-
LD
1.5
pacity(kW)
ND 0.75
(4poles)
Rated
VLD 4.1
output
LD 3.1
current
ND 2.5
(A)
Overload VLD
current LD
rating ND
Rated output voltage
VLD 2.8
400V LD 2.1
Rated
ND 1.7
capa-
city
VLD 3.6
(kVA)
460V LD 2.7
ND 2.2
VLD 4.9
Rated input
current LD 3.7
(A)*1)
ND 3.0
Rated input AC voltage
*2)
VLD 3.7
Power
supply
LD 2.8
capacity
ND 2.3
(kVA) *3)*8)
VLD
Carrier
frequency LD
variation *4)
ND
Starting torque *5)
Regenerative
Minimum resistance
100
value(Ω)
H(height)(mm)
255
W(width)(mm)
150
D(Depth)(mm) 140
Protective structure
Aprox.weight (kg) 3
*1) The rated input current is the value when the drive is operated in the rated output current. The value of the impedance at the supply side changes
due to the wiring, breaker, input reactor, etc.
*2) Make sure the following for Low Voltage Directive (LVD) compliant.
- Pollution degree 2, - Overvoltage category 3 (for 380 to 460Vac Input supply),
*3) The power supply capacity is the value of the rated output current at 440V. The value of the impedance at the supply side changes due to the wiring,
breaker, input reactor, etc.
*4) The setting range of carrier frequency [bb101] / [bb201] is limited according to the [Ub-03] setting(load type selection).
It is recommended to set the carrier frequency settings [bb101]/[bb201] equal or greater than the (maximum output frequency x 10)Hz.
For induction motor IM, it is recommended to set the carrier frequency to 2 kHz or more except V/f control. For synchronous motor
(SM)/Permanent magnet motor (PMM), it is recommended to set the carrier frequency to 8 kHz or more.
*5) The value is specified for the Hitachi standard motor controlled by the sensorless vector control when ND rating.
Torque characteristics may vary by the control system and the use of the motor.
*6) The key height of keypad is excluded from dimensions. When an option is connected, the depth is increased. Refer to the each optional Guide.
*7) Usually an external regenerative braking unit is required. However, with an optional built –in chopper braking circuit and external discharge resistor
can eliminate a external regenerative unit. The built-in chopper braking circuit is offered by order. In order to purchase, contact the nearest sales
office.
015 022 037 055 075
2.2 3.7 5.5 7.5 11
2.2 3.7 5.5 7.5 11
1.5 2.2 3.7 5.5 7.5
5.4 8.3 12.6 17.5 25.0
4.8 6.7 11.1 16.0 22.0
4.0 5.5 9.2 14.8 19.0
Three-phase(3 wire)380 to 460V (Corresponding to the incoming voltage)
3.7 5.8 8.7 12.1 17.3
3.3 4.6 7.7 11.1 15.2
2.8 3.8 6.4 10.3 13.2
4.7 7.2 10.9 15.2 21.7
4.2 5.8 9.6 13.9 19.1
3.5 4.8 8.0 12.8 16.5
6.4 9.9 15.0 20.8 29.8 36.9 47.6 56.0 73.8 91.7 110.7 138.1 175.0 209.5 253.6 300.0 376.2
5.7 8.0 13.2 19.0 26.2 34.5 44.0 51.2 67.9 83.3 101.2 125.0 160.7 190.5 232.1 273.8 345.2
4.8 6.5 11.0 17.6 22.6 29.8 38.1 46.4 57.1 72.6 89.3 108.3 133.3 178.6 214.3 258.3 309.5
Control power supply: Single-phase supply 380 to 460V ( Permissible AC voltage 323 to 506V) ,
50Hz(allowable variation range: 47.5 to 52.5Hz)/60Hz (allowable variation range:57 to 63Hz)
Main circuit power supply: Three-phase(3 wire) 380 to 460V ( Permissible AC voltage 323 to 506),
50Hz(allowable variation range: 47.5 to 52.5Hz)/60Hz(allowable variation range: 57 to 63Hz)
4.9 7.5 11.4 15.9 22.7 28.1 36.3 42.6 56.3 69.9 84.4 105.2 133.4 159.7 193.2 228.6 286.7
4.4 6.1 10.1 14.5 20.0 26.3 33.6 39.0 51.7 63.5 77.1 95.3 122.5 145.2 176.9 208.7 263.1
3.6 5.0 8.3 13.4 17.2 22.7 29.0 35.4 43.5 55.3 68.0 82.6 101.6 136.1 163.3 196.9 235.9
Internal BRD circuit (external discharge resistor value)
100 100 70 70 35
255 255 255 260 260
150 150 150 210 210
140 140 140 170 170
3 3 3 6 6
110 150 185 220 300
15 18.5 22 30 37
15 18.5 22 30 37
11 15 18.5 22 30
31.0 40.0 47.0 62.0 77.0 93.0
29.0 37.0 43.0 57.0 70.0 85.0
25.0 32.0 39.0 48.0 61.0 75.0 91.0
110% 60sec / 120% 3sec
120% 60sec / 150% 3sec
150% 60sec / 200% 3sec
21.5 27.7 32.6 43.0 53.3 64.4 80.4 101.8 121.9 147.6 174.6 218.9
20.1 25.6 29.8 39.5 48.5 58.9 72.7
17.3 22.2 27.0 33.3 42.3 52.0 63.0
26.8 34.6 40.7 53.7 66.7 80.5 100.5 127.3 152.4 184.5 218.2 273.7
25.1 32.0 37.2 49.4 60.6 73.6 90.9 116.9 138.6 168.9 199.2 251.1
21.7 27.7 33.8 41.6 52.8 65.0 78.8
0.5 to 10.0kHz
0.5 to 12.0kHz
0.5 to 16.0kHz
200%/0.3Hz
35 24 24 20 15
260 390 390 390 540
210 245 245 245 300
170 190 190 190 195
IP20 – UL Open Type
6 8.5 8.5 8.5 22
- Overvoltage category 2 (for over 460Vac Input supply)
7-1
Specifications
370 450 550 750 900 1100 1320
45 55 75 90 110
45 55 75 90 110
37 45 55 75 90
116 147 176 213
105 135 160 195
112 150 180
93.5 110.9 135.1 159.3 200.9
77.6 103.9 124.7 150.3 180.1
97.0 129.9 155.9 187.9 225.2
0.5 to 8.0kHz
0.5 to 8.0kHz
0.5 to 10.0kHz
180%/0.3Hz
*7) Ext. regen. braking unit
15 10 10
550 550 550 700 700
390 390 390 390 390
250 250 250 270 270
31 31 31 41 41
132 160
132 160
110 132
252 316
230 290
217 260
-
740 740
480 480
270 270
53 53