Table of Contents
Advertisement
Quick Links
INSTALLATION MANUAL FOR THE
FP5000
INTRINSICALLY SAFE TRANSMITTERS,
OPTION CODE 2AR
m
PERSONAL INJURY
WARNING
DO NOT USE these products as safety or
emergency stop devices or in any other
application where failure of the product
could result in personal injury.
Failure to comply with these
instructions could result in death or
serious injury.
m
WARNING
The operator of this instrument is
advised that if the equipment is used in a
manner not specified in this manual, the
protection provided by the equipment may
be impaired.
Failure to comply with these
instructions could result in death or
serious injury.
CAUTION
Only qualified, service-trained personnel
who are aware of the hazards involved
should connect external wiring to these
products.
CAUTION
Use supply wires suitable for 5 °C above
surrounding ambient.
008-0751-00
m
WARNING
Explosion Hazard - Do not disconnect
equipment unless power has been
switched off or the area is known as
non-hazardous.
m
WARNING
Explosion Hazard - Substitution of
components may impair suitability for
Class I, Division 1.
Rev. C
Advertisement
Table of Contents
Related Manuals for Honeywell FP5000 2AR Series
Summary of Contents for Honeywell FP5000 2AR Series
- Page 1 008-0751-00 Rev. C INSTALLATION MANUAL FOR THE FP5000 INTRINSICALLY SAFE TRANSMITTERS, OPTION CODE 2AR PERSONAL INJURY WARNING Explosion Hazard - Do not disconnect WARNING equipment unless power has been DO NOT USE these products as safety or switched off or the area is known as emergency stop devices or in any other non-hazardous.
-
Page 2: Normal Use
008-0751-00, Rev. C TRANSMITTERS DESCRIPTION to presence of transient protection devices that activate above 33 Vdc The Honeywell Model FP5000 with and protect the transmitter from option code 2AR is an “Intrinsically overvoltage damage. This is intended Safe” certified media-isolated... -
Page 3: Installation Requirements And Cautions
MOUNTING DIMENSIONS Use appropriate tools (such Refer to the FP5000 datasheet for as an open-ended wrench or detailed mounting dimensions. deep-well socket) to install transmitters. FP5000 Pressure Transmitter User Manual | sps.honeywell.com/ast... - Page 4 The product can reach maximum surface temperature of 135°C [275°F] under fault conditions at ambient Maximum surface temperature of 85°C [185°F] and maximum surface temperature temperature of 100°C [212°F] under fault conditions at ambient temperature of 40°C [104°F] FP5000 Pressure Transmitter User Manual | sps.honeywell.com/ast...
-
Page 5: Intrinsically Safe Installation
The certification is valid when the sensor has been installed as per the installation drawings referenced in this section. FIGURE 1. WIRING, FP5000 2AR, TWO-WIRE AMP FP5000 Pressure Transmitter User Manual | sps.honeywell.com/ast... -
Page 6: Zero Adjustment
Protecting the product from continued exposure to moisture or fluids at the electrical connection will eliminate premature internal failure of the product. FP5000 Pressure Transmitter User Manual | sps.honeywell.com/ast... - Page 7 • EN IEC 60079-0 • ANSI/UL 60079-11 • EN 60079-11 • UL 61010-1 Standards used for IECEx Certification • IEC 60079-0 • IEC 60079-11 LABEL MARKING The standard product label includes the following: FP5000 Pressure Transmitter User Manual | sps.honeywell.com/ast...
- Page 8 FP5000 INTRINSICALLY SAFE 008-0751-00, Rev. C TRANSMITTERS FP5000 Pressure Transmitter User Manual | sps.honeywell.com/ast...
- Page 9 FP5000 INTRINSICALLY SAFE 008-0751-00, Rev. C TRANSMITTERS FP5000 Pressure Transmitter User Manual | sps.honeywell.com/ast...
- Page 10 While Honeywell may provide application assistance personally, through our literature and the Honeywell web site, it is buyer’s sole responsibility to determine the suitability of the product in the application. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this writing.