Advertisement
Quick Links
OXYTHERM
INSTALLATION INSTRUCTIONS
Please read the operating and mounting instructions before using the equipment. Install the equipment in
compliance with the prevailing regulations.
Bedrijfs- en montagehandleiding voor gebruik goed lezen! Apparaat moet volgens de geldende
voorschriften worden geïnstalleerd.
Lire les instructions de montage et de service avant utilisation! L'appareil doit imperativement être installé selon les règle-
mentations en vigueur.
Betriebs- und Montageanleitung vor Gebrauch lesen! Gerät muß nach den geltenden Vorschriften
installiert werden.
MANUFACTURER AND IMPORTER ADDRESSES
Below are the addresses and contact information for the Honeywell – Maxon manufacturing location and European sales office. The
European sales office serves as the importer and EU manufacturer's representative under the EU New Legislative Framework (NLF).
MUNCIE, INDIANA, USA – MANUFACTURER
201 East 18th Street
P.O. Box 2068
Muncie, IN 47307-0068
Tel: 765.284.3304
Fax: 765.286.8394
®
FHR Dual Fuel Burners
INSTRUCTION MANUAL
EUROPEAN SALES OFFICE –
IMPORTER
BELGIUM
Maxon International BVBA
Luchthavenlaan 16-18
1800 Vilvoorde, Belgium
Tel: 32.2.255.09.09
Fax: 32.2.251.82.41
Storage
®
OXYTHERM
FHR burners shall be stored dry (inside).
Burner blocks have been cured carefully before shipment
and shall be kept dry. Wetting of the blocks could result in
premature failures.
32M-92012-02
Advertisement
Related Manuals for Honeywell Maxon OXYTHERM FHR
Summary of Contents for Honeywell Maxon OXYTHERM FHR
- Page 1 MANUFACTURER AND IMPORTER ADDRESSES Below are the addresses and contact information for the Honeywell – Maxon manufacturing location and European sales office. The European sales office serves as the importer and EU manufacturer's representative under the EU New Legislative Framework (NLF).
-
Page 2: Burner Mounting
® OXYTHERM FHR DUAL FUEL BURNERS Handling Burner mounting ® The views on page 2 show two possible methods for OXYTHERM FHR burners are shipped as complete units. ® Handle burners with care, using proper equipment, during mounting and holding an OXYTHERM FHR burner block unpacking, transport, lifting and installation. - Page 3 ® OXYTHERM FHR DUAL FUEL BURNERS Alternate burner mounting arrangement 1) By others Burner installation procedure Burners should not be installed in a down-fired position. Read the entire installation procedure before proceeding The primary objective is to seal the burner block in the wall with the installation of oxygen-fuel burners.
- Page 4 ® OXYTHERM FHR DUAL FUEL BURNERS CAUTION Staged oxygen control valve must be placed in position #1 as shown in Technical Catalog 32M-02012 to provide optimal cooling to the burner. 1) Service plate 2) Cooling flow 3) Staged oxygen control valve (set to position #1 for optimal cooling) View port...
-
Page 5: Maintenance Instructions
® OXYTHERM FHR DUAL FUEL BURNERS Start-up MAINTENANCE INSTRUCTIONS Typical ignition sequence WARNING IMPORTANT The OXYTHERM® FHR burner is provided with OXYTHERM® FHR burners do not include means quick release clamps to allow for rapid change- for self ignition. Burner ignition procedure is the over between gas and oil firing. - Page 6 ® OXYTHERM FHR DUAL FUEL BURNERS 32M-92012—02 E - i - 7/99...
- Page 7 ® OXYTHERM FHR DUAL FUEL BURNERS E - i - 7/99 32M-92012—02...
- Page 8 ® OXYTHERM FHR DUAL FUEL BURNERS For More Information The Honeywell Thermal Solutions family of products includes Honeywell Combustion Safety, Eclipse, Exothermics, Hauck, Kromschröder and Maxon. To learn more about our products, visit ThermalSolutions.honeywell.com or contact your Honeywell Sales Engineer.