Page 1
TANGO® SOLO ST User manual * TG9920- 2020.05 *Original instructions...
Page 2
Installation diagram TANGO SOLO ST 50 min CW I...
Page 3
Installation diagram TANGO SOLO ST with fridge 50 min CW I...
Page 4
DO = Drain outlet CWI = Cold water inlet G 3/8″ EI = Electricity inlet...
Page 5
Foreword The installation, use and maintenance manual (hereinafter Manual) provides the user with information necessary for correct and safe use of the machine (or “appliance“). The following must not be considered a long and exacting list of warnings, but rather a set of instructions suitable for improving machine performance in every respect and, above all, preventing injury to persons and animals and damage to property due to im- proper operating procedures.
Contents A SAFETY INFORMATION ......................... 7 General information ........................7 General safety ..........................7 Personal protection equipment ......................8 Transport, handling and storage ...................... 8 Installation and assembly ....................... 9 Water connection.......................... 9 Electrical connection ........................9 Use ............................10 appliance cleaning and maintenance ....................
SAFETY INFORMATION General information To ensure safe use of the appliance and a proper understanding of the manual it is necessary to be familiar with the terms and typographical conventions used in the documentation. The following symbols are used in the manual to indicate and identify the various types of hazards: WARNING Danger for the health and safety of operators.
Personal protection equipment Summary table of the Personal Protection Equipment (PPE) to be used during the various stages of the machine's service life. Stage Protective Safety Gloves Glasses Safety garments footwear helmet — ● ○ — ○ Transport — ● ○...
Installation and assembly • The installation must be carried out by a specialised personnel. • Follow the installation instruction supplied with the appliance. • Do not install a damaged appliance. Any missing or faulty parts must be replaced with original parts. •...
isolation fault in the TN or TT systems or, for IT systems, the use of isolation controllers or differential current protection devices to activate automatic power disconnection (an isolation controller must be provided for indicating a possible first earth fault of a live part, unless a protection device is supplied for switching off the power in case of a such a fault.
– inadequate or interrupted water supply, steam, air, gas Check on Electrolux Professional website the list of authorized (including impurities and/or other that does not comply customer care. with the technical requirements for each machine);...
C.4.1 Appliance with 2 positions main switch • keeping combustible or flammable materials, or in any case materials not compatible with or pertinent to the work, near • 0 = appliance OFF the machine; • 1 = appliance ON • wrong machine installation; •...
Water Pressure MPa. Water Pressure max port personnel. Manufacturer Electrolux Professional SpA or any other The data plate gives the product identification and technical service centre authorised by Electrolux data. The meaning of the various information given on it is Professional SpA.
This manual is intended solely for consultation by the operator IMPORTANT and can only be given to third parties with the permission of When installing the machine, make sure the ELECTROLUX. electrical connection is carried out in compliance with that specified on the data plate. Keeping the manual...
• knowledge of the regulations on work hygiene and safety. electrical cable sheathing, etc.) the operator for normal machine use must: In case of a significant anomaly (e. g. short circuits, wires coming out of the terminal block, motor breakdowns, worn TECHNICAL CHARACTERISTICS Data table Capacities...
• Confirm by pressing the “YES“ key for 3 seconds if you have 1. “STOP function“: emptied the drawer, and the “NO“ key if you have not The Stop icon stops a cycle in progress instantly, regard- emptied it. less of what it is. If the “cycle repetition“ function is enabled, press twice to stop.
Cleaning milk (in the case of a milk pump system) • Press this icon to start milk cleaning. • Follow the instructions. • When the cleaning is complete put fresh milk in the milk tank. Detergent part number 92027. Jug part number 54212. External cleaning NOTE! We recommend dismantling the coffee and milk...
It is advisable to stipulate a preventive and scheduled maintenance contract with the Customer Care Service. Preventive maintenance for coffee products Indication of Different consumption for coffee products. Consumption Coffee/week in Consumption Coffee/ year in Number of cups/weeks (130 Annual Meter Statement CUPS/KG) Inferior to 15 Inferior to 800...