Advertisement
ure.
leaks, clogged nozzles, and missing or damaged parts. Have damaged
product repaired before use. Many accidents are caused by poorly maintained
products.
k or
ging
Be aware of any hazard presented by the chemical solutions. Always follow the
the
chemical manufacturer's instructions on usage, handling, and storage.
Do not use the product with any material where the hazard is not known.
Ensure that the spray wand is securely connected to the spray wand handle
before using the product. If necessary, use pliers to attach the spray wand to
only
the spray wand handle.
tool
Properly replace and tighten the spray tank cover after pouring liquid into
the spray tank.
only
After long time storage or after winter, spray the product with clean water.
Check if there are any leakages or cracks.
Always follow the chemical manufacturer's instructions printed on their
product labelling for use, cleaning, and storage. Chemicals should be stored
out of the reach of children.
oper
To reduce the risk of fire or explosion, do not use the product with flammable
liquids, such as gasoline or other chemicals with a flashpoint below 55°C.
ental
Operate the product only in temperatures between 0°C and 40°C.
miliar
Store the product in a location where the ambient temperature is between
0°C and 40°C.
ocal
Injuries may be caused, or aggravated, by prolonged use of a tool. When using
with
any tool for prolonged periods, ensure that you take regular breaks.
Wear personal protective equipment at all times when using the product.
ctive
For safety purposes, use the product correctly and in accordance with the
operator's manual and relevant chemical Safety Data Sheets (SDS) to avoid
rate
exposure to hazardous chemicals.
MIXING THE SOLUTION
Mix the chemicals strictly in accordance with the manufacturer's instructions.
Incorrect mixtures may produce toxic fumes or explosive solutions.
Never use undiluted liquid plant control chemicals.
Prepare the solution and fill the container outdoors or in well-ventilated areas
only.
fety
e of
Prepare only sufficient solution for the job in hand so that nothing is left over.
dous
Do not mix different chemicals unless such mixture is approved by the
manufacturer.
indy
FILLING THE CONTAINER
ects
Make sure that the container is completely emptied and cleaned before a
different chemical is filled in.
nt of
been
Remove the battery pack before filling the container. Wipe off any spills before
installing the battery pack.
nt is
Stand the product on a level surface, and do not fill the container above the
n all
maximum mark.
ose)
When filling from the tap, do not immerse the end of the hose in the chemical
outh.
solution. Sudden low pressure in the system may cause the chemical solution
hing
to be sucked back into the water supply.
rials
Before filling the container with solution, carry out a test run with fresh water,
hem
and check all parts of the product for leaks.
dical
Make sure that the tank cap is properly closed after filling.
Hang a tag on the product to note the chemical solution being used.
with
Chemical solutions may be premixed and poured into the spray tank using a
funnel, if necessary.
NOTE: Thoroughly clean and rinse measuring containers that are used for
filling the tank and for premixing chemical solutions.
APPLICATION
Work only in the open or in well-ventilated locations, e.g., open greenhouses.
Indoor use is restricted to chemicals that are recommended by the chemical
manufacturer for indoor use.
Adjust the pressure by rotating the cone nozzle or changing to a fan nozzle.
mine
oses,
Too high or too low pressure or unfavourable weather conditions can result
in the wrong solution concentration. Overdosing may damage plants and the
environment. Underdosing may result in unsuccessful plant treatment.
To reduce the risk of damage to the environment and plants, do not operate
the product:
■
if pressure is too high or too low
■
in windy conditions
■
in direct sunlight
Avoid using the product in freezing weather because the solution may freeze.
The product may be subject to national requirements for regular inspection by
designated bodies, as provided for in Directive 2009/127/EC of the European
Parliament and of the Council of 21 October 2009 establishing a framework for
Community action to achieve the sustainable use of pesticides.
ADDITIONAL BATTERY SAFETY WARNINGS
To reduce the risk of fire, personal injury, and product damage due to a short
circuit, never immerse the tool, battery pack, or charger in fluid or allow fluid
to flow inside them. Corrosive or conductive fluids, such as seawater, certain
industrial chemicals, and bleach or bleach-containing products, etc., can cause
a short circuit.
Charge the battery pack in a location where the ambient temperature is
between 10°C and 38°C.
Store the battery pack in a location where the ambient temperature is
between 0°C and 40°C.
Use the battery pack in a location where the ambient temperature is between
0°C and 40°C.
MAINTENANCE
Use only original manufacturer's replacement parts, accessories, and
attachments. Failure to do so can cause possible injury, can contribute to poor
performance, and may void your warranty.
Servicing requires extreme care and knowledge and should be performed only
by a qualified service technician. Have the product serviced by an authorised
service centre only.
To avoid serious personal injury, always remove the battery pack from the
product when cleaning or performing any maintenance.
Do not use flammable solvents or abrasive cleaning agents to clean the
product.
After each use, clean the product as prescribed in this manual.
CLEANING THE REFILLABLE CONTAINER
Drain all chemical solutions from the refillable container into a container
approved for chemicals. Do not store the chemicals in the refillable container.
Use clean water to clean and rinse the refillable container. A small amount
of mild household detergent may be added. It may be necessary to rinse the
refillable container more than once.
CLEANING THE PRODUCT
Do not use flammable solvents or abrasive cleaning agents to clean the
product.
1.
Fill the tank about one-third full with clean water. A small amount of
mild household detergent may be added.
2. Spray into a suitable container until the tank has been emptied.
3. Refill and repeat the procedure with clean water. It may be necessary
to rinse the tank more than once, then drain again as directed above.
4. Allow all parts to completely dry, then reinstall the tank cap.
5. Wipe the outside of the fogger with a clean, dry cloth.
37
37
Advertisement
