Linksys MGBLH1 User Manual
Gigabit sfp modules gigabit ethernet 1000 base-t mini-gbic sfp transceiver gigabit ethernet sx mini-gbic sfp transceiver gigabit ethernet lh mini-gbic sfp transceiver
Hide thumbs
Also See for MGBLH1:
- User manual (169 pages) ,
- User manual (156 pages) ,
- User manual (72 pages)
Related Manuals for Linksys MGBLH1
Summary of Contents for Linksys MGBLH1
- Page 1 ® A Division of Cisco Systems, Inc. Gigabit SFP Modules Gigabit Ethernet 1000 Base-T Mini-GBIC SFP Transceiver Gigabit Ethernet SX Mini-GBIC SFP Transceiver User Guide WIRED Gigabit Ethernet LH Mini-GBIC SFP Transceiver Model No. MGBT1, MGBLH1, MGBSX1...
-
Page 2: Table Of Contents
Table of Contents Chapter 1: Using the Gigabit SFP Modules Introduction Installation and Removal Directions for the MGBLH1 and MGBSX1 3 Installation and Removal Directions for the MGBT1 Appendix A: Specifications Appendix B: Warranty Information Appendix C: Regulatory Information Appendix D: Contact Information... -
Page 3: Chapter 1: Using The Gigabit Sfp Modules
SR2024 or SR224G, creating new Gigabit ports. Each Gigabit SFP Module is hot-swappable, meaning you can connect them even when the switch is running. Use the following directions for installing and removing either the MGBLH1 and MGBSX1 or the MGBT1. Installation and Removal Direc-... - Page 4 4. Now the fiber is connected to the Gigabit SFP Module and should be functioning. Connect the other end of the cable to an SFP Module to verify that the fiber connection is complete. 5. Press the fiber cable’s connector and pull to remove the fiber cable from the Gigabit SFP Module.
-
Page 5: Installation And Removal Directions For The Mgbt1
Installation and Removal Directions for the MGBT1 1. Insert the Gigabit SFP Mod- ule with the printed side up and the pull tab facing out. 2. Lock the Gigabit SFP Module in place. 3. Connect the Cat5 cable to the Gigabit SFP Module’s port. - Page 6 4. Press the RJ-45 connector’s tab and pull to remove the Cat5 cable from the Gigabit SFP Module. 5. To remove the Gigabit SFP Module, begin by pulling the Module’s pull tab. 6. Now, remove the Gigabit SFP Module. Figure 1-11: Remove the Cat5 cable Figure 1-12: Pull the pull tab Figure 1-13: Remove the MGBT1...
-
Page 7: Appendix A: Specifications
0ºC to 40ºC (32ºF to 104ºF) -20ºC to 70ºC (-4ºF to 158ºF) 0% to 85%, Non-Condensing 5% to 90%, Non-Condensing Compliant with Specifications of SFP Transceiver MSA Specification 850 nm (850nm TYP., 830-860nm) MMF (Multi-Mode Fiber) MMF: 62.5/125um fiber @ 160 MHz/km to 220m minimum distance 62.5/125um fiber @ 200 MHz/km to 275m minimum distance... - Page 8 Operating Temp.: Storage Temp.: Operating Humidity: Storage Humidity: MGBLH1 Standards: Cabling Type: Dimensions: Unit Weight: Power: Operating Temp.: Storage Temp.: Operating Humidity: Storage Humidity: Input Power: -20 – -17 dBm Stress Sensitivity: 50/125 um: -13.5dBm, 62.5/125 um: -12.5dBm 3.3V Power Supply 0ºC to 40ºC (32ºF to 104ºF)
-
Page 9: Appendix B: Warranty Information
You. This warranty gives You specific legal rights, and You may also have other rights which vary by jurisdiction. This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated, repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident. -
Page 10: Appendix C: Regulatory Information
Canadian regulations. EC DECLARATION OF CONFORMITY (EUROPE) Linksys declares that the Wireless-G ADSL Gateway conforms to the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC: EN 301 489-1, 301 489-17 General EMC requirements for Radio equipment. - Page 11 European community and countries that have adopted the European R&TTE directive 1999/5/EC. For more details on legal combinations of power levels and antennas, contact Linksys Corporate Compliance. Linksys vakuuttaa täten että Wireless-G ADSL Gateway tyyppinen laite on direktiivin 1999/5/ EY oleellisten vaatimusten ja sitä...
- Page 12 If this equipment causes harm to the telephone network, the telephone company may discontinue your service temporarily. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
-
Page 13: Appendix D: Contact Information
Can't find information about a product you want to buy on the web? Do you want to know more about networking with Linksys products? Give our advice line a call at: Or fax your request in to: If you experience problems with any Linksys product,...