Advertisement
TRANSPORTING LITHIUM BATTERIES
Transport the battery pack in accordance with local and national provisions
ct. If
and regulations. Follow all special requirements on packaging and labelling
tion
when transporting batteries by a third party.
Ensure that no batteries can come in contact with other batteries or conductive
hear
materials while in transport by protecting exposed connectors with insulating,
and
non-conductive caps or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further advice.
ting
MAINTENANCE
the
WARNING! Use only original manufacturer's replacement parts,
ment
accessories, and attachments. Failure to do so can cause possible injury,
can contribute to poor performance, and may void your warranty.
new
WARNING! Servicing requires extreme care and knowledge and
nce.
should be performed only by a qualified service technician. Have the
the
product serviced by an authorised service centre only. When servicing,
use only original replacement parts.
■
Turn off the product and remove the battery pack before conducting any
parts
maintenance or cleaning work.
worn
■
You may only make adjustments or repairs described in this manual. For
tre.
other repairs, contact an authorised service centre.
and
■
Before any maintenance or adjustment, disable the product by removing
the power source.
and
■
For the replacement line, use only a nylon filament line of the diameter
described in the specifications table of this manual.
njury
■
After extending the new cutter line, always return the product to its
normal operating position before starting.
any
■
After each use, clean the product with a soft, dry cloth. Any part that
is damaged should be properly repaired or replaced by an authorised
the
service centre.
ntil it
■
Check all nuts, bolts, and screws before each use and at frequent intervals
for proper tightness to ensure that the product is in safe working
r by
condition. Any part that is damaged should be properly repaired or
tect
replaced by an authorised service centre.
■
Bring the product to an authorised service centre to replace damaged or
rcuit
unreadable labels.
RESIDUAL RISKS
d or
t off
E
ven when the product is used as prescribed, it is still impossible to completely
ghly
eliminate certain residual risk factors. The following hazards may arise during
use, and the operator should pay special attention to avoid the following:
erly
■
injury caused by vibration
–
Hold the product by the designated handles, and restrict working
ctly
time and exposure.
■
injury caused by exposure to noise
–
Wear hearing protection, and limit exposure.
■
injury caused by flying debris
duct
–
Wear eye protection at all times.
k, or
tive
RISK REDUCTION
h or
It has been reported that vibrations from handheld tools may contribute
to a condition called Raynaud's Syndrome. Symptoms may include tingling,
numbness, and blanching of the fingers, usually apparent upon exposure to
cold. Hereditary factors, exposure to cold and dampness, diet, smoking, and
ct to
work practices are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the operator to possibly
reduce the effects of vibration:
■
tted.
Keep your body warm in cold weather. When operating the product, wear
ct in
gloves to keep the hands and wrists warm. It is reported that cold weather
Keep
is a major factor contributing to Raynaud's Syndrome.
and
■
After each period of operation, exercise to increase blood circulation.
■
Take frequent work breaks. Limit the amount of exposure per day.
nt or
If you experience any of the symptoms of this condition, immediately
discontinue use and see your physician.
WARNING! Injuries may be caused, or aggravated, by prolonged use
of a tool. When using any tool for prolonged periods, ensure that you take
regular breaks.
SYMBOLS
Read and understand all instructions before operating the
product. Follow all warnings and safety instructions.
Regulatory Compliance Mark (RCM). Product meets
applicable regulatory requirements.
Wear ear protection.
Wear eye protection.
Wear non-slip safety footwear when using the product.
Do not expose the product to rain or damp condition.
Beware of thrown or flying objects. Keep all bystanders,
especially children and pets, at least 15 m away from the
operating area.
Do not use metal blade(s) on the product.
Rotational direction and maximum speed of the shaft for
the cutting attachment.
6250
Keep hands away from the cut-off blade.
Remove the battery pack before starting any work on the
product.
100
Guaranteed sound power level
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling
advice.
The following signal words and meanings are intended to explain the levels of
risk associated with this product.
DANGER
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
CAUTION
Without safety alert symbol
Indicates a situation that may result in property damage.
29
29
Advertisement
