Montage-Anschluss-Anleitung TouchCenter BUS-2 1. Sicherheitshinweise Lesen Sie die Anleitung sorgfältig und vollständig durch, bevor Sie das Gerät installieren und in Betrieb nehmen. Sie erhalten wichtige Hinweise zur Montage, Programmierung und Bedienung. Das Gerät ist nach dem neuesten Stand der Technik gebaut. Benutzen Sie das Gerät nur: - bestimmungsgemäß...
Montage-Anschluss-Anleitung TouchCenter TFT BUS-2 4. Allgemeines Das Grafik-Bedienteil TouchCenter kann zusammen mit der Einbruchmelderzentralen-Reihe 561- MB100 / HB48 / MB48 / MB24 / HB24, sowie mit der EMZ MB256 plus verwendet werden. Der Anschluss erfolgt über den BUS-2. Mit dem Grafik-Bedienteil können Informationen über den...
Montage-Anschluss-Anleitung TouchCenter TFT BUS-2 6. Übersicht 6.1 Vorderseite LED rot Leuchtet: Einbruchalarm Blinkt: Sabotage- oder Überfallalarm LED grün Leuchtet: Gerät ist betriebsbereit Blinkt: Gerät ist nicht betriebsbereit LED gelb Leuchtet: Allgemeine Störung der Zentrale Blinkt: Netzstörung der Zentrale 6.2 Rückseite Einhängelöcher für...
Montage-Anschluss-Anleitung TouchCenter TFT BUS-2 7. Anschluss Sabotagekontakt und Abreißsicherung BUS-2 Anschluss BUS-2 Schirmanschluss Montagerahmen Klemmenleiste BUS-2 Anschluss 7.1 Hinweise zur Einstellung der BUS-2 Adresse Die BUS-2 Adresse muss bei der Inbetriebnahme eingestellt werden. Bei Erstinbetriebnahme von werkseitig ausgelieferten Geräten erfolgt nach Anlegen der Betriebs- spannung eine Grundinitialisierung.
Montage-Anschluss-Anleitung TouchCenter TFT BUS-2 7.2 Installationshinweise Die BUS-2 Anschlussleitung muss als abgeschirmte Leitung ausgeführt sein. Dabei dürfen die Abschirmungen nicht als 0V-Zuleitungen verwendet werden. Leitungslängen Der Montageort der Energieversorgung (Zentrale) sollte möglichst nahe am Bedienteil liegen. Bitte entnehmen Sie die max. Leitungslängen folgenden Tabellen: ÜÞ...
Montage-Anschluss-Anleitung TouchCenter TFT BUS-2 9. Endmontage Nach dem elektrischen Anschluss wird das Bedienteil mit den Einhängelöchern auf den Montagerahmen aufgesetzt und nach unten geschoben Beim Montieren darauf achten, dass der Sabotagekontakt betätigt wird und die Anschlussleitungen nicht beschädigt werden. Wand 10.
Montage-Anschluss-Anleitung TouchCenter TFT BUS-2 11. Anhang - Einbindung einer Grafik als Hintergrundbild Es besteht die Möglichkeit eine Grafik als Hintergrundbild (z.B. Firmenlogo) einzublenden. Das Einspielen der Grafik erfolgt über den im Grafikbedienteil integrierten Kartenleser. Der Kartenleser befindet sich unter der Gehäuseklappe oben am Bedienteil. Für das Einspielen von Grafiken wird £...
Mounting and Connection Instructions TouchCenter Keypad TFT BUS-2 1. Safety instructions Please read these instructions carefully and completely before installing and starting to work with this unit. This manual contains important information on installation, programming and operation. The unit has been built in accordance with state-of-the-art standards. Only use the unit: - according to the designated use and - in technically perfect and correctly installed condition - according to the technical data.
Mounting and Connection Instructions TouchCenter Keypad BUS-2 4. General The operating and display panel TouchCenter supplements the intruder alarm control panels 561- MB100 / HB48 / MB48 / MB24 / HB24 and also MB256 plus. The connection to the operating and display panel required a BUS-2 connection.
Mounting and Connection Instructions TouchCenter Keypad TFT BUS-2 6. Overview 6.1 Front view LED red Lights up: Intrusion alarm Flashes: Tamper- or hold-up alarm LED green Lights up: Unit is ready LED yellow Lights up: General system fault of the central control panel Flashes: Mains fault of the central control panel...
Mounting and Connection Instructions TouchCenter Keypad TFT BUS-2 7. Connection Tamper and tear off protection switch BUS-2 connection BUS-2 Shield connection at the mounting frame Screw terminal for BUS-2 connection 7.1 Notes for set up the BUS-2 address The BUS-2 address has to be set up during commissioning. The device will be initialized to standard settings after the operation voltage has been connected for the first time to a device in ex-works condition.
Mounting and Connection Instructions TouchCenter Keypad TFT BUS-2 7.2 Installation hints The BUS-2 connection lead must be a shielded lead. The shielding should not be used as 0V feed lines. "Conductor length” The installation site of the power supply should be as close as possible to the operating unit. The following table contains the maximum conductor length: Distance between power supply and operating unit: line cross-section of Ø...
Mounting and Connection Instructions TouchCenter Keypad TFT BUS-2 9. Final mounting After the electrical connection, fit the operating and display module with the fixing holes to the mounting frame and push it down Take care to activate the tamper switch and not to damage the cables while mounting. wall 10.
Mounting and Connection Instructions TouchCenter Keypad TFT BUS-2 11. Appendix - Integration of a wallpaper There is the possibility to use an own logo as wallpaper (e.g. company logo). The import can take place via the integrated card reader. The card reader is located under the flap of the upper side of the housing.