Specifications - Makita RP0910 Instruction Manual

ENGLISH
1-1. Adjusting knob
1-2. Stopper pole
1-3. Depth pointer
1-4. Stopper pole setting nut
1-5. Lock knob
1-6. Fast-feed button
1-7. Adjusting hex bolt
1-8. Stopper block
2-1. Nylon nut
3-1. Stopper pole
3-2. Hex nut
3-3. Adjusting hex bolt
3-4. Stopper block
4-1. Lock button
4-2. Switch trigger
5-1. Speed adjusting dial

SPECIFICATIONS

Collet chuck capacity
Plunge capacity
No load speed (min
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
For Model RP0910
For European countries only
Noise and Vibration
The typical A-weighted sound pressure level is 83 dB (A).
Uncertainty is 3 dB(A).
The noise level under working may exceed 85 dB (A).
Wear ear protection.
The typical weighted root mean square acceleration
value is not more than 2.5 m/s
These values have been obtained according to
EN60745.
Explanation of general view
6-1. Collet nut
6-2. Tighten
6-3. Loosen
6-4. Wrench
6-5. Shaft lock
7-1. Correct size collet cone
8-1. Workpiece
8-2. Bit revolving direction
8-3. View from the top of the tool
8-4. Feed direction
9-1. Feed direction
9-2. Bit revolving direction
9-3. Workpiece
9-4. Straight guide
11-1. Lock screw
11-2. Guiding surface
Model
-1
)
Overall height
Net weight
Safety class
2
.
RP0910
8 mm or 1/4"
0 - 57 mm
27,000
260 mm
3.3 kg
ENE010-1
For Model RP1110C
For European countries only
ENF002-1
Noise and Vibration
The typical A-weighted sound pressure level is 80 dB (A).
Uncertainty is 3 dB(A).
The noise level under working may exceed 85 dB (A).
The typical weighted root mean square acceleration
value is not more than 2.5 m/s
These values have been obtained according to
EN60745.
ENG003-2
For Model RP0910,RP1110C
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this
product is in compliance with the following standards of
standardized documents;
EN60745, EN55014, EN61000 in accordance with
Council Directives, 89/336/EEC, 98/37/EC.
5
11-3. Straight guide
14-1. Screw
14-2. Templet guide
15-1. Bit
15-2. Base
15-3. Templet
15-4. Workpiece
15-5. Distance (X)
15-6. Outside diameter of the templet
guide
15-7. Templet guide
16-1. Dust nozzle assembly
16-2. Nozzle assembly
17-1. Limit mark
18-1. Brush holder cap
18-2. Screwdriver
/II
Wear ear protection.
2
.
Yasuhiko Kanzaki CE2005
RP1110C
8 mm or 1/4"
0 - 57 mm
8,000 - 24,000
260 mm
3.4 kg
/II
ENG003-2
ENH101-5