AEG L9FEC49S User Manual
  1. Manuals
  2. Brands
  3. AEG Manuals
  4. Washer
  5. L9FEC49S
  6. User manual

AEG L9FEC49S User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

L9FEC49S
USER
MANUAL
EN
User Manual
Washing Machine

Advertisement

Table of Contents
loading

Related Manuals for AEG L9FEC49S

Summary of Contents for AEG L9FEC49S

  • Page 1 L9FEC49S User Manual Washing Machine USER MANUAL...

  • Page 2: Table Of Contents

    17. ACCESSORIES......................42 FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it.

  • Page 3: Safety Information

    ENGLISH SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.

  • Page 4: Safety Instructions

    The ventilation opening in the base (if applicable) • must not be covered by a carpet, mat, or any floor covering. The appliance must be connected to the water mains • using the new supplied hose sets, or other new hose sets supplied by the Authorised Service Centre.

  • Page 5: Installation

    ENGLISH cable. Should the mains cable need • Do not put flammable products or to be replaced, this must be carried items that are wet with flammable out by our Authorised Service Centre. products in, near or on the appliance. •...
  • Page 6 2. Remove the cardboard top and the Make sure not to damage polystyrene packaging materials. the hoses. 7. Remove the polystyrene protection from the bottom. 3. Remove the internal film. 8. Fully clean and dry the bottom of the appliance.
  • Page 7 ENGLISH It is possible to see water • A (FRONT) = Front of the flowing from the drain hose. appliance This is due to the testing • B (BACK) = Rear of the appliance with water of the appliance 10. Remove the adhesive strip from the in factory.
  • Page 8 Make sure that carpets do not stop the air circulation below the appliance. Make sure that the appliance does not touch the wall or other units. 2. Loosen or tighten the feet to adjust the level. WARNING! Do not put cardboard, wood...
  • Page 9 ENGLISH If this occur, close the water tap and contact the authorized service centre to replace the hose. Make sure that the drain 3.5 Water drainage hose end is not immersed in the water. There may be a The drain hose should stay at a height of return of dirty water into the not less than 60 cm and not more than appliance.

  • Page 10: Product Description

    5. Without the plastic hose guide, to 6. Position the hose directly to a built- a sink spigot - Put the drain hose in in drain pipe in the room wall and the spigot and tighten it with a tighten it with a clamp.
  • Page 11 ENGLISH 4.2 Appliance overview 11 12 Worktop Detergent dispenser and salt compartment Control panel Door handle Rating plate Drain pump filter Feet for levelling the appliance Salt Drain hose Inlet hose connection Mains cable Compartment for washing phase: powder detergent, stain remover. Transit bolts If using liquid Hose support...

  • Page 12: The Water Softener (Softwater Technology)

    Compartment for salt. Salt After a washing cycle, if Read carefully 'The necessary, remove any Water Softener detergent residue from the technology ( Soft detergent dispenser. Water)'. Maximum level for detergent/ additives quantity. When selecting a prewash phase, put the detergent/ additive in a dosing ball inside the drum.
  • Page 13 ENGLISH Once you have entered the menu by pressing and the buttons: 1. Touch the button. The goes This setting increases the salt consumption. 2. Touch the Start/Pause button to confirm your choice and exit the menu. How to deactivate the water 4.
  • Page 14 5.3 Pouring salt Salt The compartment can contain about The water softener function acts through 600 gr of salt that are sufficient for about special resins present in the appliance. 20 - 300 washing cycles (or 4 - 70 weeks)

  • Page 15: Before First Use

    ENGLISH 6. BEFORE FIRST USE 1. Make sure that all transit bolts have This action activates the drain system. been removed from the appliance. 5. Pour a small quantity of detergent 2. Make sure that the electrical power is into the compartment marked by available and the water tap is open.
  • Page 16 Temperature touch button On/Off push button (On/Off) (Temperature) 7.2 Display Maximum load indicator. The icon flashes during laundry load esti- mation (refer to "PROSENSE load detection" paragraph). Maximum laundry indicator. It flashes when the laundry load exceeds the maximum declared load of the selected programme.

  • Page 17: Dial And Buttons

    ENGLISH OKO MIX indicator. Steam phase indicator. Anti-crease phase indicator. Child safety lock indicator. Time saving indicator. Temperature indicator. The indicator appears when a cold wash is set. Spin speed indicator. Rinse hold indicator. Extra silent indicator. Pre-wash indicator. Stain indicator. Extra rinse indicator.
  • Page 18 When the display shows the indicators 8.5 Stain/Prewash , the appliance does not Press this button repeatedly to activate heat the water. one of the two options. 8.4 Spin The relevant indicator goes on in the display. When you set a programme, the appliance automatically selects the •...
  • Page 19 ENGLISH If the Extra Rinse is set as a If you select the Cotton default option and you programme at 40°C or 60°C select a compatible washing and no other options are set, programme, the display the display shows the shows .

  • Page 20: Programmes

    8.11 Delay Start appliance begins the countdown. With this option you can delay the start of a programme in a more convenient 8.12 Start/Pause time. Touch the Start/Pause button to start, Touch the button repeatedly to set the pause the appliance or interrupt a required delay.
  • Page 21 ENGLISH Programme Programme description Machine washable wool, hand washable wool and delicate fabrics with «hand washing» care symbol. Wool/Silk Steam programme Steam programme for cotton and synthetic items. Steam can be used for dried , washed or worn once laundry. This Steam programme reduce creases and odours and relaxes the fi-...
  • Page 22 Programme Programme description Do not use fabric softener and make sure that Outdoor there is no softener residue in the detergent dispenser. Synthetic sport items. This programme is designed to gently wash modern outdoor sporting garments and is also suitable for sporting clothes such as gym, cycling or jogging and simi- lar.
  • Page 23 ENGLISH Programme Default temperature Maximum spin speed Maximum load Temperature range Spin speed range 1.5 kg Steam 30 °C 1400 rpm 5 kg OKOPower 60 °C - 30 °C 1400 rpm - 400 rpm 1400 rpm 60 °C 9 kg 1400 rpm - 400 rpm Anti-Allergy 30 °C...

  • Page 24: Settings

    ■ ■ ■ ■ ■ ■ ■ ■ ■ Only Drain ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Delay Start Plus Steam ■ ■ ■ ■ ■ ■ ■ ■ ■ Soft Plus 1) This option is not available with temperature lower than 40 °C.

  • Page 25: Daily Use

    ENGLISH • You activate the appliance (special • To activate/deactivate this option short tune). touch the button and the • You deactivate the appliance (special button simultaneously the relevant short tune). indicator comes on/goes off. • You touch the buttons (click sound). This option adds two rinses and the •...
  • Page 26 CAUTION! Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the laundry. 11.3 Filling the detergent and additives We recommend that you do not exceed the maximum 4.
  • Page 27 ENGLISH The drain pump can operate shortly before the appliance fills water. 11.6 Starting a programme with the delay start 1. Touch the Delay Start button repeatedly until the display shows the desired delay time. The indicator goes on. 2. Touch the Start/Pause button. 3.
  • Page 28 11.8 Programme phase After touching the Start/Pause button, the maximum declared load indicator indicators goes off, the indicator flashes, the When the programme starts the indicator ProSense starts the laundry load of the running phase flashes and the detection: other phase indicators are steady on.
  • Page 29 ENGLISH 11.10 Cancelling a running In the display all washing phase indicators become steady and the time programme area shows . 1. Press the button On/Off to cancel The indicator of the Start/Pause button the programme and to deactivate goes off. the appliance.

  • Page 30: Hints And Tips

    • You do not use the appliance for 5 • If you have set , the appliance minutes before you touch the Start/ only drains the water. Pause button. The option indicator goes out, Press the button On/Off to activate the appliance again.

  • Page 31: Care And Cleaning

    ENGLISH 12.3 Detergents and other other treatments without exceeding treatments the indicated maximum level ( • Use the recommended detergents for • Only use detergents and other the type and colour of the fabric, the treatments specially made for programme temperature and the washing machines: level of soil.
  • Page 32 13.4 Door seal Regularly examine the seal and remove all objects from the inner part. 2. Remove the insert for the softener and, if inserted, the container for 13.5 Cleaning the drum liquid detergent. Regularly examine the drum to prevent rust particles.
  • Page 33 ENGLISH 13.7 Cleaning the drain pump 4. Make sure that all detergent residue is removed from the detergent conveyor. Use a cloth. WARNING! Disconnect the mains plug from the mains socket. Regularly check the drain pump filter and make sure that it is clean.
  • Page 34 4. Let the water flow out. 8. If it is necessary, remove fluff and objects from the filter recess. 9. Make sure that the impeller of the pump can rotate. If it does not rotate, contact the Authorised Service Centre.
  • Page 35 ENGLISH 12. Close the pump access. 2. Remove the inlet hose from the appliance by loosening the ring nut. When you drain the water with the emergency drain procedure, you must 3. Clean the valve filter on the back of activate the drain system again: the appliance with a toothbrush.

  • Page 36: Troubleshooting

    13.10 Frost precautions If the appliance is installed in an area where the temperature can reach the values around 0° C or drop below, remove the remaining water from the inlet hose and the drain pump. 1. Disconnect the mains plug from the mains socket.
  • Page 37 ENGLISH • - No communication between WARNING! electronic elements of the appliance. Deactivate the appliance Switch it off and switch on again. before carrying out any check. • - The anti-flood device is on. Disconnect the appliance and close the water tap. Contact the Authorised Service Centre.
  • Page 38 Problem Possible solution • Make sure that the couplings of the water hoses are tight and there is not water leakages. There is water on the • Make sure that the water inlet hose and the drain hose have floor.
  • Page 39 ENGLISH Problem Possible solution • Check if the water softener has been set to act also during Excessive consumption rinse phase. Refer to 'How to set the water hardness level' of salt. in 'The Water Softener technology (Soft Water)' chapter. After the check, activate the appliance.

  • Page 40: Consumption Values

    2. Eliminate any trace of detergent or additive and clean the compartment thoroughly. 3. Insert the drawer back and pour salt Salt in the compartment 4. Close the drawer. 5. Run a cotton or synthetic cycle, without reducing time, to restore the water softener function.

  • Page 41: Technical Data

    ENGLISH Programmes Load Energy Water Approxi- Remain- (kg) consump- consump- mate pro- ing mois- tion (kWh) tion (litre) gramme ture (%) duration (minutes) 0.24 Standard 40°C cotton 1) At the end of spin phase. 2) The performance results and low energy consumption are guaranteed by the use of softened water. To maintain this achievement over time, it is essential to set the right water hardness level by following the user manual instructions and use salt regularly for regenerating the resins .

  • Page 42: Accessories

    Read carefully the instructions supplied using the correct stacking kit with the accessory. manufactured and approved by AEG. 18. ENVIRONMENTAL CONCERNS marked with the symbol with the Recycle the materials with the symbol household waste.
  • Page 43 ENGLISH...
  • Page 44 www.aeg.com/shop...

Table of Contents