COLOR TELEVISION RECEIVER Chassis : S51A Model: CK765DSX3X/NWT COLOR TELEVISION RECEIVER CONTENTS Precautions Specifications and IC Data Disassembly and Reassembly Alignment and Adjustment Troubleshooting Exploded View and Parts List Electric Parts List Block Diagram PCB Layout Diagram Wiring Diagram Schematic Diagrams...
The current measured should the XÐray Protection Specifications Label, and not exceed 0.5 milliamp. Reverse the power- the Product Safety and X-ray Warning Note on plug prongs in the AC outlet and repeat the the service data schematic. test. Samsung Electronics...
Page 4
14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheat- ing, and correct any potential hazards. Samsung Electronics...
Page 5
Make sure that the portion around the serviced part has not been damaged. 8. Always connect a test instrumentÕs ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrumentÕs ground lead last. Samsung Electronics...
Page 6
4. Do not use freon-propelled chemicals. These unpackaged replacement ESDs. Motions such can generate electrical charges that damage as brushing clothes together, or lifting a foot ESDs. from a carpeted floor can generate enough static electricity to damage an ESD. Samsung Electronics...
V H F ,U H F : T ele s c op ic dip o le ante nn a (75 W u nb alanc ed ty pe ) Sp ea k er Im p ed anc e : 8 W , 1 0W + 10 W or 16 W , 5W + 5W (533C only) Samsung Electronics...
Page 8
NICAM DE MODULATOR IC A01 L A7567N SIF DETEC TOR A2 STE R EO MODUL E IC A02 TDA9873H A2 DEMODULATOR ICM01 LA7566 SIF & FM DE TE C TOR MONO IC S01 TEA5114 VIDE O SWITCH RGB -S/W Samsung Electronics...
Page 9
24W16(Pin 8) TDA9859(Pin 32) TRANSISTOR SAW-FILTER TRANSISTOR G1962 2SD1651 UPC574J K2950M 2SD1650 K9253M KSD5072 KSA815-Y KA33V G3956M KSD5071 KSA539-Y KSD1711 E B C TRANSISTOR TRANSISTOR KA7630 KSR1012 KA7812 KSR1010 KSR2010 E C B Fig. 2-1 Semiconductor Base Diagrams Samsung Electronics...
Disassembly and reassembly 3. Disassembly and Reassembly 3-1 Back Cover Removal 1. After removing the 7 screws, pull the cabinet backwards. Samsung Electronics...
Page 12
11. Separate the TBC wire 2P, speaker wires from the wire clamper. 12. Separate the CN701, CN602 connector from the wire clamper. 13. Separate the AC cord from the wire clamper. 14. Remove the main board by pulling it with both hands. Samsung Electronics...
Page 13
Disassembly and reassembly 3-3 Speaker Removal 1. Remove the speaker by pressing the tension rib. 1. Separate the speaker wires from D-coil (located on the bottom to the right side). 2. Remove the screws. Samsung Electronics...
Page 14
(1) Always lift the picture tube by grasping it firmly around the faceplate, (2) Never lift the tube by its neck. (3) Do not scratch the picture tube or apply excessive pressure. Fractures of the glass may cause an implosion. Samsung Electronics...
6. Cancel the Adjustment Mode by re-pressing ment parameters are listed in the accompany- the ÒHIDDENÓ or ÒPower OFF/ONÓ keys. ing table, and selected by pressing the CHANNEL keys ( , ). After adjustments are completed, re-start the TV set. Samsung Electronics...
Page 17
This pattern is used for pre-heating the CRT during manufacturing--it is accessed in the factory by twice pressing the ÒFACTORY Ò key. Even if the TV power is cut off, the Aging Mode is not cancelled, The AGING mode is cancelled by repressing the ÒHIDDENÓ or any key on the front pannel. Samsung Electronics...
Page 18
SECAM-L/L', PAL/SECAM-B/G PAL - I ( UHF BAND ONLY) SYSTEM PAL/SECAM - B/G,D/K PAL/SECAM -B/G PAL -B/G ATM FUNCTION USED ATS OPTION ATM FUNCTION NOT USED FIELD POS PHILIPS CRT USED FIELD POL FIELD NEG OTHER CRT USED Samsung Electronics...
Page 19
7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts. 8. To protect against shock hazard, use an isola- tion transformer. Samsung Electronics...
Page 20
2. Input a gray scale pattern. (Use a pattern generator, PM5518) 3. Use the Picture mode for the STANDARD pic- ture. 4. Adjust the Screen VR (on the FBT) so that the voltage on the oscilloscope becomes 140+2.5V (See Fig. 4-1). 140 2.5V Fig. 4-1 Samsung Electronics...
Page 21
Set SCT to 40 ± 5 fL in the Factory Service Mode with using CA100. (See Fig. 4-4 (c) Low-Light Adjustment Set SBT to 1.5 ± 0.2 fL in the Factory Service Fig. 4-4 Mode with using CA100. (See Fig. 4-4 Samsung Electronics...
Page 22
4-Pole Magnet Movement Fig. 4-5 Center Convergence Adjustment 4-3-9 RF AGC Adjustment 1. Tune to the strongest local station. 2. Enter the Factory Service Mode to make adjustments. 3. Adjust the AGC control untill noise(snow) disappears from the screen. Samsung Electronics...
Page 23
4. Adjus t PHS s o that the pic ture is horizontally centered. 5. Adjus t with PEW s o that the left and right margins of the picture are 5. 6. Input a crosshatch pattern. 7. Adjus t PEP, PEC , PET for vertical linearity. Samsung Electronics...
5-1 No Video (Raster On, No Sound) Measure the Check/Replace Voltage of each of, 8 pins TU101, HC101 of TU101 Check/Replace Check IC901 IC901,IC201,IC902 ,IC701, Pins 39, 40 Audio Module See "No Sound" See "No Video" (Video OK) (Sound OK) Samsung Electronics...
Page 27
A/V Front Assembly. 5-5 Power OFF/ON (Repeatedly) CHECK Q403 SEE " NO-POWER" COLLECTOR H-PULSE CHE CK/REPLACE CHE CK IC901 IC901,Q907,C913 PIN26(H-SYNC ) DZ402 CHE CK IC301 CHE CK/REPLACE PIN7(V-BLANK) Q301,Q302,D304 CHE CK/REPLACE CHECK PIN6(+16.5V) R409,R413,D407,D410 PIN1(-14V) DZ302,DZ303 CHECK/RE PLACE IC301,IC201 Samsung Electronics...
Page 28
(2) W he n F 802 is okay, but S MP S doe s n ot fu nction: C he ck/Replace D Z80 1 , D Z8 08 , IC 80 2 , D Z8 05 . (3) O the rs: S ee "5. Tro ublesh ooting" Samsung Electronics...