Specifications; Router Safety Warnings - Makita RP1110CJ Instruction Manual

ENGLISH
(Original instructions)
1 Adjusting knob
2 Stopper pole
3 Depth pointer
4 Stopper pole setting nut
5 Lock knob
6 Fast-feed button
7 Adjusting hex bolt
8 Stopper block
9 Nylon nut
10 Lock button
11 Switch trigger
12 Speed adjusting dial
13 Collet nut

SPECIFICATIONS

Model
Max. collet capacity ..................................................................... 8 mm or 1/4"
Plunge capacity ........................................................................... 0 – 57 mm
–1
No load speed (min ) ................................................................. 27,000
Overall height .............................................................................. 260 mm
Net weight .................................................................................... 3.3 kg
Safety class .................................................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

ROUTER SAFETY WARNINGS

1. Hold power tool by insulated gripping surfaces,
because the cutter may contact its own cord.
Cutting a "live" wire may make exposed metal parts
of the power tool "live" and shock the operator.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by your hand or against the body
leaves it unstable and may lead to loss of control.
3. Wear hearing protection during extended period
of operation.
4. Handle the bits very carefully.
Explanation of general view
14 Wrench
15 Shaft lock
16 Tighten
17 Loosen
18 Correct size collet cone
19 Workpiece
20 Bit revolving direction
21 Feed direction
22 View from the top of the tool
23 Straight guide
24 Lock screw
25 Guiding surface
26 Templet guide
5.
6.
ENE010-1 7.
8.
9.
ENF002-2 10. Before using the tool on an actual workpiece, let
11. Be careful of the bit rotating direction and the
12. Do not leave the tool running. Operate the tool
GEA010-1 13. Always switch off and wait for the bit to come to
14. Do not touch the bit immediately after operation;
15. Do not smear the tool base carelessly with thin-
16. Use bits of the correct shank diameter suitable
GEB018-4
17. Some material contains chemicals which may be
18. Always use the correct dust mask/respirator for
SAVE THESE INSTRUCTIONS.
27 Screw
28 Bit
29 Base
30 Templet
31 Workpiece
32 Distance (X)
33 Outside diameter of the templet
guide
34 Nozzle assembly
35 Dust nozzle assembly
36 Limit mark
37 Brush holder cap
38 Screwdriver
RP0910
/II
Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged
bit immediately.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Hold the tool firmly with both hands.
Keep hands away from rotating parts.
Make sure the bit is not contacting the work-
piece before the switch is turned on.
it run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
feed direction.
only when hand-held.
a complete stop before removing the tool from
workpiece.
it may be extremely hot and could burn your
skin.
ner, gasoline, oil or the like. They may cause
cracks in the tool base.
for the speed of the tool.
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
the material and application you are working
with.
RP1110C
8 mm or 1/4"
0 – 57 mm
8,000 – 24,000
260 mm
3.4 kg
/II
5