Sealey EH30001 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Indoor Use
instruction
Only
manual
This product is only suitable for well insulated areas or occasional use.
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! ELECTRICAL INSTALLATION OF THE HEATER TO A 3-PHASE 415VOLT SUPPLY MUST ONLY BE CARRIED OUT BY A
‰
QUALIFIED ELECTRICIAN.
Make sure the power supply cable is correctly connected to the earth. It is the user's responsibility to read, understand and
comply with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads,
plugs and all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of
appropriate safety devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. You must
also read and understand the following instructions concerning electrical safety.
The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
1.1.1.
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and the
safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure insulation on all cables and the product itself is safe before connecting to mains power supply.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage, especially power connections, to ensure
that none are loose.
Important: Ensure the voltage marked on the product is the same as the electrical power supply to
1.1.6.
be used. A 3 phase plug must be used.
1.1.7. DO NOT pull the powered appliance by the power cable.
1.1.8. DO NOT pull power plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damage leads, plugs or connections. Replace or have repaired Immediately
by a qualified electrician.
1.1.10. This product must be fitted with a 3-phase plug according to the diagram, and will require
a minimum of 63A per phase of electrical supply. You must contact a qualified electrician to
ensure an appropriately fused supply is available.
Connect GREEN/YELLOW wire to earth (E) terminal
Connect the live wires to live 1, 2 and 3.
When completed, check that there are no bare wires, that all wires have been connected
correctly, that the cable external insulation extends beyond the cable restraint and that the
restraint is tight.
1.2. GENERAL SAFETY
1.2.1. MAINTENANCE PRECAUTIONS
WARNING! Disconnect the heater from the mains power supply, before servicing or performing
‰
any maintenance.
Servicing or maintenance must only be carried out by an authorised service agent.
Check that the heater is in sound condition and good working order. Take immediate action to repair or replace damaged parts.
9
Use recommended parts only. Unapproved parts may be dangerous and will invalidate the warranty.
9
DO NOT attempt to repair a damaged heater, contact an authorised service agent.
8
1.2.2. POSITIONING OF HEATER
WARNING! DO NOT use the heater near flammable material, liquids, solids, gases or compressed gas cylinders etc.
‰
DO NOT place the heater close to a bath, wash basin, shower, swimming pool or any other water-filled area or wet surface.
8
DO NOT place the heater up against any surface such as a wall, door or furniture etc.
8
DO NOT place the heater immediately below any electrical outlet.
8
Position the heater at least a minimum of 0.5mtr at the rear and sides, and 2mtr at the front, from any walls or objects.
9
1.2.3. OPERATIONAL PRECAUTIONS
The heater must only be used by people who have read these instructions and have been trained in its use.
9
DO NOT obstruct the air inlet and outlet sections of the heater.
8
DO NOT cover the heater.
8
DO NOT touch the heater casing or grille when first switched off, as these will be very hot and will take time to cool.
8
© Jack Sealey Limited
INDUSTRIAL FAN HEATER 30kW 415V 3ph
EH30001
MODEL No:
Do Not
Cover
Original Language Version
.
EH30001 Issue 7 12/10/21