Page 2
WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,...
Page 3
Wireless Bridge Quick Start Guide DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
Page 4
Wireless Bridge Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Page 5
Wireless Bridge Quick Start Guide Model Received Transmitted Bandwidth Frequency frequency frequency power DS-3WF 5180 to 5240 5180 to 5240 20 MHz, 40 802.11ac: 23 Series MHz and 80 5260 to 5320 5260 to 5320 802.11ac: 23 5500 to 5700 5500 to 5700 802.11ac: 30 Model...
Page 6
Wireless Bridge Quick Start Guide 1. this device may not cause interference, and 2. this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence.
Page 7
Wireless Bridge Quick Start Guide Preface Applicable Models This manual is applicable to the DS-3WF Series wireless bridge. Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a hazardous situation which, if not avoided, will or could Danger result in death or serious injury.
Page 8
Wireless Bridge Quick Start Guide Do not connect several devices to one power adapter as adapter overload may cause over- ● heating or a fire hazard. Please make sure that the plug is firmly connected to the power socket. ●...
Wireless Bridge Quick Start Guide Chapter 1 Introduction The 5 GHz gigabit wireless bridge (hereinafter referred to as the device) is used for long-distance wireless connection, which is suited for outdoor video security and transmission between sites in a LAN. The device supports 16 SSIDs, point-to-point as well as point-to-multipoint transmission. 1.1 Interface/Button Figure 1-1 Interface/Button of Wireless Bridge Table 1-1 Interface/Button Description...
Wireless Bridge Quick Start Guide 1.2 SSID 4-character SSID can realize 16 kinds of matching ways by switching the DIP up or down. Note Please switch the CPE/AP DIP to set what the device is used as before setting the SSID. Table 1-2 SSID No.
Wireless Bridge Quick Start Guide Table 1-3 Indicator Description Indicator Description Signal Strength Solid The devices are matched. Indicator Solid red, yellow and green: RSSI ≥ -60, the ● wireless signal is strong. Solid red and yellow, unlit green: -75 ≤ RSSI ●...
Wireless Bridge Quick Start Guide Chapter 2 Installation 2.1 Preparations for Installation To avoid device damage or personal injury caused by improper useage of the device, please follow the preparations below. Use the attached power adapter and PoE injector to power the device. ●...
Page 15
Wireless Bridge Quick Start Guide Figure 2-1 Thread Cable Ties 2. Fix and fasten the cable ties on the pole. Figure 2-2 Pole Mounting Finished Note Adjust the direction of the device manually to keep it vertical in forward direction.
Wireless Bridge Quick Start Guide 2.3 Wall Mounting Mount the device on a flat and stable wall with 2 M4 expansion bolts. Steps Note It is ease to take down the device for wall mounting. Please mount with caution. 1. Drill two parallel holes, about 54.5 mm apart. 2.
Wireless Bridge Quick Start Guide Figure 2-4 Hang the Device 4. Make sure the device is mounted stably and vertically in forward direction. Figure 2-5 Wall Mounting Finished 2.4 Connection and Power On Use the attached power adapter and PoE injector to power on the device.
Wireless Bridge Quick Start Guide 2.4.1 AP Connection Steps 1. Switch the CPE/AP DIP to set the device as AP. 2. Select an SSID No. Example SSID No. 1 (All Down). Figure 2-6 AP Connection Note See Table 1-2 for detailed information about SSID No. ●...
Page 19
Wireless Bridge Quick Start Guide Figure 2-7 CPE Connection 3. Optional: If there are more than one CPE (no more than 4) to be matched with one AP, repeat the previous steps connect and set the CPEs. What to do next Note See Indicator for details after connection to check device powering, network connection and ●...
Wireless Bridge Quick Start Guide Chapter 3 Activation and Login You can manage the device using the iVMS 4200 software or the Web browser. Before managing the device, you need to activate and log in to the device first. Note Make sure the device is powered on and connected to the network correctly.
Wireless Bridge Quick Start Guide Chapter 4 Get More Information You can manage the device using the iVMS-4200 software or the Web browser. Scan the QR code below for iVMS-4200 software operations. ● Scan the QR code below for Web browser operations. ●...