Samsung Jet Bot VR50T95 Series User Manual
Hide thumbs
Also See for Jet Bot VR50T95 Series:
- User manual (312 pages) ,
- User manual (24 pages) ,
- User manual (150 pages)
Related Manuals for Samsung Jet Bot VR50T95 Series
Summary of Contents for Samsung Jet Bot VR50T95 Series
- Page 1 Jet Bot User manual VR50T95**** Series • Before operating this unit, please read the instructions carefully. • For indoor use only...
-
Page 2: Table Of Contents
APPENDIX Safety information SmartThings App Setting up the wireless router INSTALLATION Downloading the SmartThings App Setting up a SAMSUNG account Installing a Clean Station Registering a device to the SmartThings App 31 OPERATION Software Update Functions of the SmartThings App... -
Page 3: Preparation
User Manual ❇ ❇ If you want to purchase an additional Dust Bag, check the Dust Bag’s model name (VCA- RDB95) and SAMSUNG logo ( ) first, then contact your nearest SAMSUNG Electronics retailer or SAMSUNG service center. Safety information •... - Page 4 State of California Proposition 65 Warning (US only) WARNING This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For battery recycling go to call2recycle.org or call 1-800-822-8837 L i - i o n Failure to meet these requirements could cause damage to the internal parts of the vacuum and void your warranty.
- Page 5 • Do not operate the vacuum in an area where there are lit candles or fragile objects on the floor. • Do not operate the vacuum in a room that has lit candles on furniture that the vacuum may accidentally hit or bump into. •...
- Page 6 Jet Bot • Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc. • Do not use without a filter in place. When servicing the unit, never put fingers or other objects into the fan chamber in case the unit accidentally turns on.
- Page 7 Power related WARNING • Please prevent any risk of electric shock or fire. – Do not damage the power cord. – Do not pull the power cord too hard or touch the power plug with wet hands. – Do not use a power source other than 120 V ~ 60 Hz and also do not use a multi-outlet to supply power to a number of devices at the same time.
- Page 8 • Be sure the Jet Bot does not suck in or touch any kind of liquids (water, beverage, filth, etc.). – The Jet Bot can be severely damaged and it may contaminate other areas if the wheels pass through liquid. •...
- Page 9 • For the very low areas where the Jet Bot may get stuck, set the No- go Zones with the SmartThings App or attach the Boundary Markers to prevent the Jet Bot from getting in. • Do not install the Clean Station in an area with a dark floor. –...
- Page 10 In use WARNING • If any abnormal sounds, smells or smoke come from the Jet Bot, immediately shut off the power switch of the Jet Bot and contact a service center. CAUTION • Using the Jet Bot on a thick carpet may damage both the Jet Bot and the carpet.
- Page 11 • When the power cord is damaged, contact a service center to get it replaced by a certified repairman. – There is a risk of fire or electric shock. • Please check with a SAMSUNG Electronics service center when replacing batteries. – Using batteries from other products can cause malfunction.
- Page 12 • Before cleaning, remove objects such as a thin electric wire (1 cm or less), socks, etc. on the floor as they can be caught in the Jet Bot’s brush or Driving Wheels. • If oil such as cooking oil is on the floor, the Jet Bot may become stationary because the floor is slippery.
- Page 13 REGULATORY NOTICE 1. FCC Notice WARNING • Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions: 1 This device may not cause harmful interference, and 2 This device must accept any interference received including interference...
- Page 14 FCC RADIATION EXPOSURE STATEMENT: • This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
-
Page 15: Installation
INSTALLATION Installing a Clean Station Status Indicator Approximately 0.5 m Approximately 0.5 m Approximately 1 Connect the provided power cord to the 2 Position the power cord into the fixing bottom of the Clean Station. groove at the rear of the Clean Station. 3 Place the Clean Station on an even floor and near an electrical outlet and plug it in. -
Page 16: Operation
OPERATION Charging the Jet Bot Before using the Jet Bot for the first time, charge it completely. (For the charging time and cleaning time, refer to the ‘Product specification’.) 1 Remove the yellow gasket attached to the power switch at the side of the Jet Bot and press the power switch to turn the Jet Bot –... - Page 17 Auto charging The Jet Bot automatically returns to the Clean station when it completes cleaning, when the Dustbin is full, or when the battery is low to recharge. Docking (Recharging) You can return the Jet Bot to the Clean Station while cleaning to recharge. •...
- Page 18 Checking if the docking (recharging) does not work Check the Clean Station’s installation status Charge the Jet Bot manually for the following conditions. • Check whether the Clean Station has been installed in a place where the Clean Station • When the Clean Station is installed in a cannot guide the Jet Bot to return.
-
Page 19: Using The Jet Bot
Using the Jet Bot Before using the Jet Bot, press the power switch at the side of the Jet Bot to turn the Jet Bot ❇ ❇ For the normal use of the Jet Bot’s functions, the SmartThings connection is required. –... -
Page 20: Operation Status On The Led Status Indicator
Operation status on the LED Status Indicator Classification Color Meaning Blinking without An error occurs. moving Blinking while Auto returning to the Clean While moving Station due to low battery operating Operating stops due to low battery Jet Bot Monitoring Blue Red, orange, or yellow (depending While charging... -
Page 21: Cleaning Functions
Cleaning Functions Cleaning Functions Operation • Auto Clean: Cleans automatically until the Jet Bot completes cleaning one time. • Room Clean: You can select a room you want to clean. • Around Furniture Clean: You can select the areas around furniture or an electronic appliance you want to clean. -
Page 22: Additional Functions
❇ ❇ When the Jet Bot does not have a saved map, it studies cleaning space through Auto Clean function which starts from the Clean Station. After studying the cleaning space, a map is saved. (The map creation is enabled through the SmartThings App only.) ❇... -
Page 23: Attaching Boundary Markers
NOTE • When a Check Notice occurs or when you carry the Jet Bot to another place and start cleaning, the Jet Bot spins left and right at a 30 degree angle to recognize its location before it starts cleaning. •... -
Page 24: Parts Diagram
Parts diagram Jet Bot 01 Obstacle Sensor 02 Power switch 03 Upper Cover 04 Docking Sensor Window 05 LiDAR Sensor 06 Fine dust Filter 07 Dustbin 08 Start/stop button 09 Docking (Recharging) button 10 Status Indicator 11 Camera 12 3D Sensor Bottom 01 Charging Pin 02 Cliff Sensor... -
Page 25: Maintenance
MAINTENANCE Cleaning the Jet Bot Before maintenance work, you should turn off the power switch at the side of the Jet Bot. Emptying and cleaning the Dustbin 1 Detach the upper cover using the groove 2 Hold the Dustbin handle and lift the under the cover. -
Page 26: Cleaning The Driving Wheel
7 Attach the filter to the Dustbin. 8 Attach the Upper Cover and the Lower Cover to the Dustbin. Make sure you can hear them click into position. 9 Attach the Dustbin to the Jet Bot. Grasp the handle and put the Dustbin into both grooves. -
Page 27: Cleaning The Brush
Cleaning the brush 1 Push the Brush Cover Lock upward to 2 Detach the brush cover. unlock. 3 Lift up the left side of the brush first and 4 Clean the brush. then pull the brush from the groove on the right. -
Page 28: Cleaning The Sensor Window
Cleaning the Sensor Window Wipe the Sensor Window with a soft cloth. Docking Sensor Obstacle Sensor Window Cliff Sensor LiDAR Sensor Dust Sensor Window Camera 3D Sensor Cleaning the Fine dust Filter For detailed methods of use and cleaning, refer to the QR code. English... -
Page 29: Cleaning The Clean Station
Cleaning the Clean Station Before cleaning the Clean Station, unplug the power cord from the electrical outlet. Replacing the Dust Bag 1 Press the [PUSH] 2 Pull the top of the button on the top Dust Bag holder of the Clean Station gently. -
Page 30: Appendix
• SAMSUNG Jet Bot supports IEEE 802.11b/g/n and Soft-AP. – IEEE 802.11n is recommended. • SAMSUNG Jet Bot supports only DHCP (Dynamic Host Configuration Protocol). Please make sure that the DHCP server option is activated on your wireless router. • The Jet Bot supports the WEP-OPEN, WPA-PSK/TKIP, and WPA2-PSK/AES for the authentication and encryption protocols. -
Page 31: Downloading The Smartthings App
• To set up a SAMSUNG account, you can follow the directions provided by the SmartThings App. • Or, if you have a SAMSUNG smartphone, you can add your SAMSUNG account in the setting app of your smartphone. Then, it will automatically sign in to your SAMSUNG account and you can use the SmartThings App. -
Page 32: Software Update
3 If a pop-up saying that a new device has been found appears, tap ADD NOW. – If the pop-up does not appear, add a device by selecting the ‘Home appliances’ category → ‘Robot cleaner’ and the Jet Bot to connect. –... -
Page 33: Functions Of The Smartthings App
Functions of the SmartThings App Classification Functions Explanation • You can check the result of the last cleaning. Cleaning Report • You can check the histories of last 50 cleanings. • The Home monitoring feature utilizes a camera on the front of the Jet Bot so you can view what is in front of the Jet Bot. - Page 34 Classification Functions Explanation • You can set the voice guide to [Voice], [Sound Sound Mode Effect], or [Mute]. Language • The Jet Bot supports 14 languages. • You can control the volume of the voice guide. Volume • You can control the sensitivity of detecting the Size of Obstacles to Avoid size of obstacles.
-
Page 35: Notes And Cautions
Notes and cautions Installation NOTE • Install the Clean Station in a place where the floor and wall are level. • If the cleaning area is wooden floors, it is best to install the Clean Station along the grain of wooden floors. •... -
Page 36: Using
• If the Jet Bot is left detached from the Clean Station, the battery will drain naturally. – Try to keep the Jet Bot being charged on the Clean Station. (However, turn off the power switch and leave the Clean Station unplugged when planning to leave the house for long periods of time by going on a business trip or vacation, etc.) Using... -
Page 37: Cleaning And Maintenance
• If it is difficult to remove foreign matter from the brush, contact an authorized SAMSUNG service center. • Since the brush sweeps dirt up from the floor during cleaning, foreign matter such as a thin and long thread, long hair, etc. may get caught in it. -
Page 38: Battery Usage
• This battery is exclusively for the SAMSUNG Electronics Jet Bot. Do not use it for any other products or purposes. • Do not disassemble or modify the battery. -
Page 39: Corrective Measures Before Reporting A Problem
Corrective measures before reporting a problem 1 The Status Indicator 2 Turn off the power 3 When turning turns red and blinks switch and check the the Jet Bot on by with a voice guide. instructions below pressing the power and take appropriate switch, the Status actions. -
Page 40: Troubleshooting
Troubleshooting Symptom Checklist • Check if the power switch is on. • Check if the Status Indicator is on. • Check if the Jet Bot's battery is depleted. – When the Jet Bot’s Status Indicator turns red and stays red, place the Jet Bot manually on the Clean The Jet Bot is not working at all. - Page 41 Symptom Checklist • Check if the Clean Station is installed along the grain of wooden floors or tiles. • The Jet Bot may clean in a diagonal direction if it is The Jet Bot suddenly cleans moving to another area using the shortest route. It diagonally.
- Page 42 Symptom Checklist • If the Jet Bot does not start cleaning from the Clean The Jet Bot does not detect and Station, the set No-go Zones function does not work. crosses No-go Zones. Therefore, start cleaning from the Clean Station to use the function.
- Page 43 SmartThings App". • When the product registration fails repeatedly, restart the SmartThings App and try the product registration. • All users should use the SAMSUNG account issued by the country which launches the product. (Applicable to iOS only) During product registration, the AP •...
- Page 44 Symptom Checklist The 'Offline' message of the Jet • Close the SmartThings App and then run it again. Bot appears on the SmartThings • Check whether there is an internet connection problem App though the Jet Bot's of the wireless router. Especially, a firewall may registration has completed interrupt standard operation.
-
Page 45: Open Source Announcement
The software included in this product contains open source software. To obtain the source code covered under licenses which have the obligation of publishing source code (e.g. GPL, LGPL… etc), please visit http://opensource.samsung.com/ and search by model name. It is also possible to obtain the complete corresponding source code in a physical medium such as a CD-ROM;... -
Page 46: Product Specification
Product Specification Classification Items VR50T95**** series Weight 4.4 kg W 305 mm x D 320 mm x H 120* mm Size (*Including LiDAR sensor: 136.5 mm) Mechanical specifications Cleaning method LiDAR location recognition Button method of the Touch type Jet Bot Power consumption of 170 W (Spot Clean) Electrical... - Page 47 Name Clean Station Rated voltage 120 V ~ 60 Hz Rated output current 25.85 V, 2.5 A Charging 80 W Power consumption Operation 1000 W (When using suction power) 5.1 kg Weight Size W 280 mm x D 400 mm x H 525 mm About 18 seconds Operating time Height...
- Page 48 If you have any questions or comments relating to SAMSUNG products, please contact the SAMSUNG customer care center. Country Customer Care Center Web Site 1-800-SAMSUNG (726-7864) www.samsung.com/ca/support (English) CANADA 1-844-SAM-PAYS (726-7297) www.samsung.com/ca_fr/support (French) 1-800-SAMSUNG (726-7864) U.S.A www.samsung.com/us/support 1-844-SAM-PAYS (726-7297)