Page 1
Assembly instructions: Eighteen A4-sized sheets. Paper craft: Fourteen A4-sized sheets with 193 parts in all These instructions apply only to the "YZ450FM". These Paper Craft parts are easier to work with when printed out on strong, thick paper (like postcard stock).
Page 2
Note To begin Basic working method and markings Tools and materials needed -Ruler - scissors - blade cutter or "Exacto-knife" - awl or other pointed tool (for making a folding crease) - felt pen - pin set - glue - hand towel ( for cleaning your fingers) - dictionary or other heavy book ( to press the papers flat).
Assembling the Fuel Tank First, assemble each component by following the Indication of working method and markings. Then, refer to the Fold or Curve Glue Working Methods illustration and photos below to glue the parts Fuel Tank Fold each relevant part according to the assembly symbols. Please use the dots on each component as reference when gluing surfaces.
Page 4
Assembling the Steering First, assemble each component by following the Indication of working method and markings. Then, refer to the Fold or Curve Glue Working Methods illustration and photos below to glue the parts Steering Fold each relevant part according to the assembly symbols. Please use the dots on each component as reference when gluing surfaces.
Page 6
Assembling the Frame-B First, assemble each component by following the Indication of Fold or Curve Glue working method and markings. Then, refer to the Working Methods illustration and photos below to glue the parts Frame Fold each relevant part according to the assembly symbols. Please use the dots on each component as reference when gluing surfaces.
Assembling the Engine First, assemble each component by following the Indication of working method and markings. Then, refer to the Fold or Curve Glue Working Methods illustration and photos below to glue the parts Engine Fold each relevant part according to the assembly symbols. Please use the dots on each component as reference when gluing surfaces.
Page 8
5 Assembling the Exhaust Pipes & Radiator First, assemble each component by following the Indication of Fold or Curve Glue working method and markings. Then, refer to the Working Methods illustration and photos below to glue the parts Exhaust Pipes Fold each relevant part according to the assembly symbols.
Page 9
Assembling the Rear Arm First, assemble each component by following the Indication of working method and markings. Then, refer to the Fold or Curve Glue Working Methods illustration and photos below to glue the parts Rear Arm Fold each relevant part according to the assembly symbols. Please use the dots on each component as reference when gluing surfaces.
7 Assembling the Side Covers & Seat First, assemble each component by following the Indication of working method and markings. Then, refer to the Fold or Curve Glue Working Methods illustration and photos below to glue the parts Side Covers Fold each relevant part according to the assembly symbols.
Assembling the Rear Fender First, assemble each component by following the Indication of working method and markings. Then, refer to the Fold or Curve Glue Working Methods illustration and photos below to glue the parts Rear Fender Fold each relevant part according to the assembly symbols. Please use the dots on each component as reference when gluing surfaces.
9 Assembling the Carburetor & Rear Suspension First, assemble each component by following the Indication of working method and markings. Then, refer to the Fold or Curve Glue Working Methods illustration and photos below to glue the parts Carburetor Fold each relevant part according to the assembly symbols. Please use the dots on each component as reference when gluing surfaces.
Assembling the Stand First, assemble each component by following the Indication of working method and markings. Then, refer to the Fold or Curve Glue Working Methods illustration and photos below to glue the parts Stand Fold each relevant part according to the assembly symbols. Please use the dots on each component as reference when gluing surfaces.
Page 14
Assembling the Front Tire First, assemble each component by following the Indication of working method and markings. Then, refer to the Fold or Curve Glue Working Methods illustration and photos below to glue the parts Front Tire Fold each relevant part according to the assembly symbols. Please use the dots on each component as reference when gluing surfaces.
Page 15
Assembling the Rear Tire First, assemble each component by following the Indication of Fold or Curve Glue working method and markings. Then, refer to the Working Methods illustration and photos below to glue the parts Rear Tire Fold each relevant part according to the assembly symbols. Please use the dots on each component as reference when gluing surfaces.
Page 16
Finish Side Covers Please use the dots on each component as reference when gluing surfaces. Seat Fuel Tank Connect each of the previously assembled parts in order from according to the diagram. Glue the ENGINE to the FRAME. Glue the REAR ARM to the FRAME. Exhaust Pipes Glue the REAR SUSPENSION to the FRAME.
Page 17
Assembled Model and the List of Parts Please refer to the photo below when attaching each component. RIGHT FRONT Exhaust Pipes Seat Fuel Tank Side Covers E- E- E- E- E- E- A- A- A- A- A- A- A- A- A- A- A- A- E- E-...
Page 18
Assembled Model and the List of Parts Please refer to the photo below when attaching each component. LEFT REAR Carburetor H- H- H- H- H- H- H- H- H- H- H- H- H- H- H- H- Engine Frame Rear Fender Rear Tire D- D- D- D-...