Honeywell 45744 Instructions

45744, 45745
PREMIUM RECESSABLE
LED PUCK LIGHTS
SAVE THESE INSTRUCTIONS FOR POSSIBLE FUTURE USE.
TO ADD ADDITIONAL PUCK LIGHTS, SEE MANUAL FOR
45739 - PREMIUM RECESSABLE LED PUCK LIGHTS EXPANSION PACK
IMPORTANT SAFETY INSTRUCTIONS
This portable light has a polarized plug (one blade is wider than the other) to reduce the risk of
electric shock. This plug fits in a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with on
extension cord unless plug can be fully inserted. Do not alter the plug. Read entire installation
instructions before you begin.
INSTALLATION INSTRUCTIONS
Carefully plan out your installation prior to securing your lights to the mounting surface or drilling
any holes for recessed mounting. Be sure to consider distances to make sure pucks will
interconnect via linking cords and that the 5ft. power cord will reach the nearest electrical outlet.
For kitchen installations, the recommended mounting for LED puck lights is near the front lip of
your kitchen under cabinets as shown in Figure 1. This provides the best light distribution across
a countertop.
1. DO NOT ATTEMPT TO INSTALL FIXTURE WHILE
PLUGGED IN.
2. Select a suitable dry mounting location (indoor only).
Make sure mounting surface is capable of supporting
the LED puck light.
3. Locate positions where the puck should be mounted.
(Keep in mind linking cords.)
4. Remove trim ring by firmly grasping ring and then firmly
pushing on back side of puck as shown in Figure 2.
5. For recessed mount applications, skip to Step 17. For
surface mount applications, continue with Steps 6-16.
6. Using the trim ring as a template, mark the locations of
the mounting holes on the mounting surface. Be sure to
orient the trim ring openings for routing linking cords.
7. Pre-drill holes in the mounting surface with a 1/16in.
(1.5mm) drill bit for soft woods and 3/32in. (2.4mm) drill
bit for hard woods.
8. Secure the trim ring with the mounting screws (included),
keeping the power cables threaded through trim ring
openings.
9. Secure the puck in the trim ring by firmly pushing the
puck into the trim ring while feeding the power cords
through the trim ring openings until the puck snaps into
place. See Figure 3.
10. The power cord has a molded plug on one end with an
in-line switch and a link connector at the other end.
The link connector plugs into the LED puck light link
connector. The two other cords provided are linking cords
with link connectors on both ends. These are used to
connect the initial LED puck to the next puck in a chain.
Link adjacent pucks only.
11. Attach the power cord link connector to the LED puck
light link connector of the initial puck installed closest to
the outlet.
12. Install the next puck close enough to the initial puck
for the 12in. link cord to reach the additional LED puck
light following Steps 1-9 of the mounting instructions.
READ IT OR WATCH IT
Read instructions or watch easy-to-follow video.
Scan QR code or visit bit.ly/2J1IM4f
FIGURE 1
CABINET
COUNTER TOP
FIGURE 2
PUSH ON BACK OF PUCK
GRASP TRIM RING
FIGURE 3
TRIM RING
MOUNTING
SCREWS
PUSH
PUCK INTO
MOUNTED
TRIM RING
13. Once installed, attach the linking cord between the initial
LED puck (previously installed) and the new LED puck.
14. Repeat steps 12-13 for each additional LED puck in a
chain.
15. When adding an additional LED puck to an existing,
compatible, LED puck installation, the power cord (with
the power plug) is not needed. Only the first LED puck
in the chain needs to be connected to power with the
power cord. Connect a maximum of 40 pucks together.
16. Plug power cord power plug into a 120VAC 60Hz outlet.
Surface mount installation is complete.
17. For Recessed Mount Applications: Discard the trim ring.
It will not be needed in recessed mount applications.
18. Mark the locations of the puck lights on the mounting
surface with a pencil. Before you drill, be sure to consider
distances to make sure pucks will interconnect via linking
cables and that the power cord will reach the receptacle.
19. Using a power drill and 2 ½in. hole saw, drill mounting
holes for the LED puck lights.
20. Route cords of LED puck lights through the holes
(see Figure 4) and press puck light into mounting hole
until fully seated (see Figure 5).
21. Connect the LED puck lights together with the 12in.
linking cords between pucks.
22. Attach the power cord link connector to the LED puck
light link connector of the puck installed closest to the
outlet.
23. Plug power cord power plug into a 120VAC 60Hz outlet.
Recessed mount installation is complete.
DIMMABLE FUNCTIONALITY
1. For use of dimming function, please purchase the
Honeywell-branded under cabinet fixture junction box,
part number 32612, and follow installation instructions
to hardwire your LED pucks.
2. Linking cords can be purchased on Amazon, part number
47167 (12in.), 47168 (18in.), 47169 (24in.), 47170
(36in.), 47171 (60in.), 47172 (48in.), 47173 (120in.).
3. Select a compatible LED dimmer.
4. Follow dimmer setup instructions for optimal
performance.
5. Compatible with the following In-wall Dimmers:
GE: Z-Wave Plus 14295, Wi-Fi 40794
Legrand: WSCL450TCCCV4, RHCL453PTCCCV6,
WSCL453PTCCCV4
Lutron: LECL-153PH, MACL-153MLH
Leviton: CD-R61-06674-12A, R01-DSL06-1TW,
CD-R00-RNL06-12B, CD-R62-06674-12A,
CD-C22-06672-12A
CLEANING INSTRUCTIONS
Your fixture is made from quality materials that will last for many
years with minimum care. When cleaning, make sure you have
unplugged your fixture and have allowed sufficient time for the
unit to cool to room temperature. You should clean the housing
and lens using a soft, dry cloth. Do not use any liquid or harsh
abrasives to clean LED puck lights.
FIGURE 4
FIGURE 5