AEG ACS58B18 Instructions Manual page 28

Keep handles dry, clean, and free from oil and grease. Greasy, oily
handles are slippery causing loss of control.
Cut wood only. Do not use chainsaw for purposes not intended.
For example: do not use chainsaw for cutting plastic, masonry or
non-wood building materials. Use of the chainsaw for operations
different than intended could result in a hazardous situation.
Causes and operator prevention of kickback:
Kickback may occur when the nose or tip of the guide bar touches
an object, or when the wood closes in and pinches the saw chain in
the cut.
Tip contact in some cases may cause a sudden reverse reaction,
kicking the guide bar up and back towards the operator.
Pinching the saw chain along the top of the guide bar may push the
guide bar rapidly back towards the operator.
Either of these reactions may cause you to lose control of the saw
which could result in serious personal injury. Do not rely exclusively
upon the safety devices built into your saw. As a chainsaw user, you
should take several steps to keep your cutting jobs free from accident
or injury.
Kickback is the result of tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below:
Maintain a firm grip, with thumbs and fingers encircling the
chainsaw handles, with both hands on the saw and position your
body and arm to allow you to resist kickback forces. Kickback
forces can be controlled by the operator, if proper precautions are
taken. Do not let go of the chainsaw.
Do not overreach and do not cut above shoulder height. This
helps prevent unintended tip contact and enables better control of
the chainsaw in unexpected situations.
Only use replacement bars and chains specified by the
manufacturer. Incorrect replacement bars and chains may cause
chain breakage and/or kickback.
Follow the manufacturer's sharpening and maintenance
instructions for the saw chain. Decreasing the depth gauge height
can lead to increased kickback.
ADDITIONAL CHAINSAW SAFETY WARNINGS
It is recommended to cut logs on a saw-horse or cradle when
operating the product for the first time.
Ensure that all guards, handles, and spiked bumper are properly fitted
and are in good condition.
Persons using the product should be in good health. The product is
heavy, so the operator must be physically fit. The operator should be
alert, have a good vision, mobility, balance, and manual dexterity. If
there is any doubt, do not operate the product.
Do not start using the product until you have a clear work area, secure
footing, and a planned retreat path away from a falling tree.
Beware of the emission of lubricant mist and sawdust. Wear a mask or
respirator, if required.
Do not cut vines or small undergrowth (less than 75 mm in diameter).
Always hold the chainsaw with both hands during operation. Use a
firm grip with thumbs and fingers encircling the chainsaw handles.
The right hand must be on the rear handle and the left hand on the
front handle.
28
Before starting the product, make sure that the saw chain is not
contacting any object.
Do not modify the product in any way or use it to power any
attachments or devices not recommended by the manufacturer.
There should be a first-aid kit containing large wound dressings and
a means to summon attention (e.g., whistle) close to the operator. A
larger more comprehensive kit should be reasonably nearby.
Wear a helmet at all times when operating the product. A helmet,
equipped with mesh visor, can help reduce the risk of injury to the
face and the head if kickback occurs.
An incorrectly tensioned chain can jump off the guide bar and could
result in serious injury or fatality. The length of the chain depends on
the temperature. Check the tension frequently.
You should get used to your new chainsaw by making simple cuts on
securely supported wood. Practice making cuts whenever you have
not operated the saw for some time.
To reduce the risk of injury associated with contacting moving parts,
always stop the motor, apply the chain brake, remove the battery pack
and make sure all moving parts have come to a stop:
■ before cleaning or clearing a blockage
■ before leaving the product unattended
■ before installing or removing attachments
■ before checking, conducting maintenance, or working on the
product
The size of the work area depends on the job being performed as
well as the size of the tree or workpiece involved. For example, felling
a tree requires a larger work area than making other cuts, such as
bucking cuts. The operator needs to be aware and in control of
everything happening in the work area.
Do not cut with your body in line with the guide bar and chain. If
you experience kickback, this position helps prevent the chain from
coming into contact with your head or body.
Do not use a back-and-forward sawing motion; let the chain do the
work. Keep the chain sharp and do not try to push the chain through
the cut.
Do not put pressure on the saw at the end of the cut. Be ready to take
on the weight of the saw as it cuts free from the wood. Failure to do so
could result in possible serious personal injury.
Do not stop the saw in the middle of a cutting operation. Keep the saw
running until it is already removed from the cut.
Personal protective equipment
Good quality personal protective equipment, as used by professionals,
will help reduce the risk of injury to the operator. The following items
should be used when operating the product:
■ Safety helmet
■ Hearing protection
■ Eye and face protection
■ Gloves
■ Leg protection (chaps)
■ Chainsaw safety boots
– Occasional users may use steel toe-cap safety boots with
protective gaiters if the ground is even and there is little risk
of tripping or catching on undergrowth
■ Chainsaw jackets for upper body protection
28
INS
TEC
CR
Un
Whe
the
you
apa
saw
end
upp
the
fibe
kerf
pinc
Pus
The
mov
for
the
ope
Saw
Stop
bar
bac
the
com
doe
to o
whe
Ska
Whe
beg
or b
prev
han
Nev
The
you
for
han
Fel
See
Whe
or m
be s
twic
in a
cau
utili
The
the
An
cuts
to th