Advertisement
Quick Links
Advertisement
Related Manuals for HIKVISION DS-2CD3B46G2T-IZHS
Summary of Contents for HIKVISION DS-2CD3B46G2T-IZHS
- Page 1 Bullet Network Camera Quick Start Guide...
- Page 2 QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR...
- Page 3 OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW.
- Page 4 on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
Page 5: Cautions And Warnings
Cautions&Warnings These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. Laws and Regulations The device should be used in compliance with local laws, electrical safety regulations, and fire prevention regulations. Transportation Keep the device in original or similar packaging while transporting it. -
Page 6: Maintenance
Do not leave the battery in an extremely high temperature surrounding environment, which may result in an explosion or the leakage of flammable liquid or gas. Do not subject the battery to extremely low air pressure, which may result in an explosion or the leakage of flammable liquid or gas. -
Page 7: Time Synchronization
DO NOT stare at operating light source. May be harmful to the eyes. Wear appropriate eye protection or DO NOT turn on the white light when you assemble, install or maintain the camera. Emergency If smoke, odor, or noise arises from the device, immediately turn off the power, unplug the power cable, and contact the service center. -
Page 8: Symbols And Marks
CAUTION: Hot parts! Burned fingers when handling the parts. Wait one-half hour after switching off before handling parts. This sticker is to indicate that the marked item can be hot and should not be touched without taking care. For device with this sticker, this device is intended for installation in a restricted access location, access can only be gained by service persons or by users who have been instructed about the reasons for the restrictions... - Page 9 Functional grounding Disposal Purchase separately Other situations Other situations omitted Waterproof Skip this step if not necessary...
- Page 10 Installation...
- Page 11 Installation...
- Page 12 Installation...
- Page 13 Installation Interface Introduction - Type 1 Memory Card Slot Reset Button Grounding Network Interface Power Input Power Output Audio Interface Alarm Interface...
- Page 14 Installation Interface Introduction - Type 2 Memory Card Slot Reset Button Grounding Network Interface Power Input Power Output RS-485 Interface Audio Interface Alarm Interface...
- Page 15 Installation Interface Introduction - Type 3 Memory Card Slot Reset Button Grounding Network Interface Power Interface Wiegand Interface Alarm Interface BNC Interface...
- Page 16 Installation 1.1* microSD...
- Page 17 Installation...
- Page 18 Installation A.1-A.4 B.1-B.4...
- Page 19 Installation 5.5mm Ø 40mm Ø...
- Page 20 Installation...
- Page 21 Installation 5.5mm Ø...
- Page 22 Installation...
- Page 23 Installation...
- Page 24 Installation...
- Page 25 Installation...
- Page 26 Installation...
- Page 27 Installation...
- Page 28 Installation...
- Page 29 Installation...
- Page 30 Installation...
- Page 31 Installation 0°-90° 0°-360° 0°-360°...
- Page 32 Installation...
- Page 33 Installation...
- Page 34 Installation 4.2*...
- Page 35 Operation Activate and Access Network Camera Scan the QR code to get Activate and Access Camera. Note that mobile data charges may apply if Wi-Fi is unavailable.
- Page 36 Operation Reset and Restore Camera Press Reset button for about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. For the position of the reset button, refer to the figures in the interface introduction page.
- Page 37 UD19834B...