Electrical Instruction - Philips 170B6CS/75 Service Manual

1. General points
1.1 During the test and measuring, supply a distortion free AC mains
voltage to the apparatus via an isolated transformer with low internal
resistance.
1.2 All measurements mentioned hereafter are carried out at a normal
mains voltage (90 - 132 VAC for USA version, 195 -264 VAC for EU
ROPEAN version, or 90 - 264 VAC for the model with full range
power supply, unless otherwise stated.)
1.3 All voltages are to be measured or applied with respect to ground,
unless otherwise stated.
Note: don' t use heat sink as ground.
1.4 The test has to be done on a complete set including LCD panel
after 30 minutes warm-up at least in a room with temperature of
25 +/- 5 degree C.
1.5 All values mentioned in these test instruction are only applicable of
a well-aligned apparatus, with correct signal.
1.6 The letters symbols (B) and (S) placed behind the test instruction
denotes
(B): carried out 100% inspection at assembly line
(S): carried out test by sampling
1.7 The white balance (color temperature) has to be tested in subdued
lighted room.
1.8 Repetitive power on / off cycle are allowed except it should be avoided
within 6 sec.
2. Input signal
2.1 Signal type
2.1.1Video signal input
Signal source: pattern generator format as attachment (Table 1 to 34)
Reference generator: QuantumData 802BTThe input signals can be
applied in two different modes:
1). VESA Analog
The video input consists of red, green, and blue signals. The video
signals are analog levels, where 0V corresponds to black and
700mV is the maximum signal amplitude. Input impedance of video
pins is 75 ohm +/- 1%.
2). Intel DVI Digital
Input signal: Single TMDS link (Three channels: RX0-/+, RX1-/+,
RX2-/+).
2.1.2 Sync signal input
The capability of sync signal inputs shall include separate sync,
composite sync and sync on green. Input impedance: 2k2 ohms.
The signals are defined as follow:
Separate sync
Composite sync
Sync on green H-sync
Signal source: pattern generator format as attachment (Table 1 to 34)
Reference generator: QuantumData 802BT
2.2 Input signal mode
The maximum resolution display of this monitor is up to 1280x1024,
SXGA signal input with full screen display. It shall also automatically
up-scale the lower resolution video modes into 1280x1024 full
screen display. The display capabilities shall include the following
timing modes:
(1) Preset modes (34 modes)
Electrical Instructions
TTL level, Positive/Negative
TTL level, Positive/Negative
TTL level, Positive/Negative
# Resolution H-Frequency
1 640X350 31.5K
2 720X400 31.5K
3 640X480 31.5K
4 640X480 35.0K
5 640X480 37.9K
6 640X480 37.5K
7 640X480 43.3K
8 800X600 35.2K
9 800X600 37.9K
10 800X600 48.1K
11 800X600 46.9K
12 800X600 53.7K
13 832X624 49.7K/
14 1024X768 48.4K
15 1024X768 56.5K
16 1024X768 60.0K
17 1024X768 61.1K
18 1024X768 68.7K
19 1152X864 54.0K
20 1152X864 63.9K
21 1152X864 67.5K
22 1152X870 68.7K
23 1152X900 61.8K
24 1152X900 71.8K
25 1280X960 60.0K
26 1280X960 75.0K
27 1280X1024 64.0K
28 1280X1024 71.7K
29 1280X1024 76.0K
30 1280X1024 80.0K
31 1280X1024 81.1K
32 688X556 31.3K
33 960X720 44.76K
34 960X720 56.4K
(2) Factory Preset modes (15 modes)
170B6 LCD
Go to cover page
Pixel rate V-Frequency Comment
25.175 70Hz IBM VGA 10h
28.322 70Hz IBM VGA 3h
25.175 60Hz
30.24 67Hz
31.5 72Hz
31.501 75Hz
36 85Hz
36 56Hz
40 60Hz
50 72Hz
49.498 75Hz
56.251 85Hz
57.28 75Hz MAC
65 60Hz
75 70Hz
78.75 75Hz
83.096 76Hz IBM XGA-2
94.5 85Hz
79.9 60Hz Non-VESA
94.5 70Hz Non-VESA
108 75Hz
100 75Hz MAC
92.94 66Hz SUN Mode IV
108 76Hz SUN Mode II
108 60Hz
129.895 75Hz Non-VESA
108 60Hz
117 67Hz SUN Mode V
130.223 72Hz DOS/V
135 75Hz
135.008 76Hz SUN Mode I
27 50Hz TV-PAL
57.58 60Hz
72.42 75Hz
17